Datasheet

ManualsBrandsPHOENIX CONTACT ManualsRack & DIN Rail Mount PSUsRail mounted PSU (DIN) QUINT-PS/1AC/24DC/5 24 Vdc 5 A 120 W 1 x

Primary-switched power supply

with SFB technology, 1 AC, output current 5 A

QUINT-PS/1AC/24DC/5

Data Sheet

INTERFACE

QUINT POWER power supply units – highest system

availability due to SFB technology

Compact power supply units of the new QUINT POWER

generation maximize the availability of your system. Even the

standard power circuit-breakers can be tripped reliably and

quickly with the SFB technology (Selective Fusebreaking

Technology) and six times the nominal current for 12 ms.

Defective current paths are disconnected selectively, the

defect is limited and the important system parts remain in

operation. A comprehensive diagnostics is carried out by

continuously monitoring the output voltage and current. This

preventive function monitoring visualizes the critical

operating modes and reports them to the control unit before

an error occurs.

1Description

DANGER OF EXPLOSION!

Remove an item only when it is not connected to power or if it is located in the non-explosive area.

DANGER

Components with dangerously high voltage and high stored energy are located in the device!

Never carry out work on live parts!

Depending on the ambient temperature and the load, the housing can become very hot!

Make sure you always use the the latest documentation.

It can be downloaded at www.download.phoenixcontact.com

A conversion table is available on the Internet at

www.download.phoenixcontact.com/general/7000_en_00.pdf.

– Quick tripping of standard power circuit breakers with

dynamic SFB technology power reserve

– Reliable starting of difficult loads with static POWER

BOOST power reserve

– Preventive function monitoring

– Can be used worldwide

– High degree of operational safety due to high MTBF

> 500 000 h, long mains buffering times > 20 ms, high

dielectric strength up to 300 V AC

103127_en_01

Summary of content (14 pages)

PAGE 1
QUINT-PS/1AC/24DC/5 Primary-switched power supply with SFB technology, 1 AC, output current 5 A INTERFACE Data Sheet 103127_en_01 1 © PHOENIX CONTACT - 05/2008 Description QUINT POWER power supply units – highest system availability due to SFB technology Compact power supply units of the new QUINT POWER generation maximize the availability of your system.
PAGE 2
QUINT-PS/1AC/24DC/5 2 Table of contents 1 Description ..................................................................................................................................1 2 Table of contents.........................................................................................................................2 3 Order data ...................................................................................................................................3 4 Technical data............
PAGE 3
QUINT-PS/1AC/24DC/5 3 Order data Description Type Order No. Pcs./Pkt. Primary-switched power supply with SFB technology, 1 AC, output current 5A QUINT-PS/1AC/24DC/5 2866750 1 Accessories Type Order No. Pcs./Pkt. Assembly adapter for QUINT POWER 2.5 A and 5 A on S7-300 rail QUINT-PS-ADAPTERS7/1 2938196 1 Universal wall adapter UWA 182/52 2938235 1 4 Technical data Input data Input nominal voltage range 100 V AC ... 240 V AC AC input voltage range 85 V AC ...
PAGE 4
QUINT-PS/1AC/24DC/5 Signal output DC OK active Output description UOUT > 0.9 x UN: High signal Voltage + 24 V DC Current ≤ 1 A (short circuit resistant) Status display "DC OK" LED green / UOUT < 0.9 x UN: LED flashing Signal output DC OK floating Output description Relay contact, UOUT > 0.9 x UN: Contact closed Voltage ≤ 30 V AC/DC Current ≤1A Status display "DC OK" LED green / UOUT < 0.
PAGE 5
QUINT-PS/1AC/24DC/5 Standards (Continued) Limitation of mains harmonic currents EN 61000-3-2 Device safety GS (tested safety) Network variants (undervoltage) Semi F47-200 Certificate CB Scheme Approvals UL rating UL Listed UL 508 UL/C-UL Recognized UL 60950 Conformance with EMC directive 89/336/EEC Immunity to interference in acc.
PAGE 6
QUINT-PS/1AC/24DC/5 5 Structure 9 5 Ou tpu tD 13 4 14 DC OK C2 - Ι< ΙN 4V 5A - - + 1 2 3 4 5 6 7 8 9 AC input DC output Active POWER BOOST switching output DC OK output active DC OK output, floating Potentiometer 18 V DC ... 29.5 V DC "DC OK" LED "BOOST" LED Universal DIN rail adapter UTA 107/30 + 3 + 2 Bo QUINT POWER ost DC OK 18- 29,5 V Inp ut AC L 100 N -24 0V PE 1 6 7 8 Input Output Signal [mm2] solid stranded 0.2 - 2.5 0.2 - 2.5 0.2 - 2.5 0.2 - 2.5 0.2 - 2.
PAGE 7
QUINT-PS/1AC/24DC/5 6 Block diagram L (+) active PFC N (-) PE DC OK I < IN 13 14 7 Safety and warning notes The power supply units are built-in devices. The device may only be installed and put into operation by qualified personnel. The corresponding national regulations must be observed. DANGER OF EXPLOSION! Remove an item only when it is not connected to power or if it is located in the non-explosive area.
PAGE 8
QUINT-PS/1AC/24DC/5 8 Installation In order to guarantee sufficient convection, we recommend observing the following minimum distance to other modules: 5 cm in the vertical direction and 0.5 cm in the horizontal direction. A lateral distance of 5 mm, and in case of active components, that of 15 mm is necessary for proper functioning of the module.
PAGE 9
QUINT-PS/1AC/24DC/5 A Slim-style installation B Assembly: Position the module with the DIN rail guide on the upper edge of the DIN rail, and snap it in with a downward motion. Removing: Pull the snap lever open with the aid of a screwdriver and slide the module out at the lower edge of the DIN rail. B A Low-profile installation Low-profile installation can be achieved by mounting the device at right-angles to the DIN rail. Mount the DIN rail adapter (UTA 107/30) as described in the figure.
PAGE 10
QUINT-PS/1AC/24DC/5 10 Connection to various network forms TN-S L N PE L N PE TN-C L N PE + − + − L PEN L N PE + − iT L N PE + − L1 L2 L3 PEN The 100 ... 240 V AC connection is established using the L, N and PE screw connections. The device can be connected to 1-phase AC networks or to two of the phase conductors of three-phase systems (TN, TT or iT systems in acc. with VDE 0100-300/IEC 60364-3) with nominal voltages of 100 V AC ... 240 V AC.
PAGE 11
QUINT-PS/1AC/24DC/5 12 Output Make sure that all output lines are dimensioned according to the maximum output current or are separately protected. The cables on the secondary side must have sufficiently large cross sections in order to keep the voltage drops on the lines as low as possible.
PAGE 12
QUINT-PS/1AC/24DC/5 Floating contact 13 DC OK Output 24 V DC 14 max. 30 V AC/DC 1A + + - - - The floating signal contact opens and signalizes a drop in the output voltage as set of more than 10%. Signals and ohmic loads of up to 30 V and currents of up to 1 A can be connected. For heavily inductive loads such as a relay, a suitable protection circuit (e.g. damping diode) is necessary.
PAGE 13
QUINT-PS/1AC/24DC/5 14 Function UOUT [V] Output characteristic curve UN I < IN I > IN U < 0,9 x UN IN IBOOST IOUT [A] The power supply unit operates with the static POWER BOOST power reserve as per the U/I characteristic curve given in the figure. In case of ambient temperatures Tamb < +40°C, IBOOST is available permanently; it is available only for a few minutes in case of higher temperatures. In the event of a secondary short circuit and overload, the output current is limited to IBOOST.
PAGE 14
QUINT-PS/1AC/24DC/5 Parallel operation Devices of the same type can be connected in parallel to enable both redundancy and an increase in efficiency. No other alignment is necessary when in the state of delivery. If the output voltage is adjusted, a uniform distribution of power is guaranteed by setting all parallel operated power supply units to exactly the same output voltage.