Operation Manual

ManualsBrandsPhoenix Gold ManualsCar AmplifiersTi800.4

Amplifier Manual

Manuel de l’amplificateur

Features

Models: Ti1500.1, Ti2500.1

Ti600.4, Ti800.4

• 24dBVariableLowPassandSubsonicCrossovers(Ti2500.1,Ti1500.1)

• 18dBVariableHighandLowPassCrossovers(Ti800.4,Ti600.4)

• Crossoversfeature41DetentsforExactFrequencySelection

• AudiophileBi-PolarOutputTransistors(Ti800.4,Ti600.4)

• HighEfciencyClassDTopology(Ti2500.1,Ti1500.1)

• MassiveUnregulatedPowerSuppliesfeaturingHandWoundTransformers

• PowerOutputPeakIndicators

• 1/0GaugeDirectInsertPowerTerminals

• LPL44-LowPassLevelControlReady

• RMD-RemoteMonitoringDisplayPort

• AdvancedThermalandProtectionCircuitry

phoenix gold ti amp manual.indd 1 3/2/10 11:20:39 AM

Summary of content (12 pages)

PAGE 1
Amplifier Manual Manuel de l’amplificateur Models: Ti1500.1, Ti2500.1 Ti600.4, Ti800.4 Features • • • • • • • • • • • 24dB Variable Low Pass and Subsonic Crossovers (Ti2500.1, Ti1500.1) 18dB Variable High and Low Pass Crossovers (Ti800.4, Ti600.4) Crossovers feature 41 Detents for Exact Frequency Selection Audiophile Bi-Polar Output Transistors (Ti800.4, Ti600.4) High Efficiency Class D Topology (Ti2500.1, Ti1500.
PAGE 2
Amplifier Owner’s Manual Specifications MONOBLOCK SPECIFICATIONS Frequency Response: Signal to Noise Ratio: Subsonic and Low Pass Crossovers: Low Pass Crossover Range: Subsonic Crossover Range: Bass Boost @ 45Hz: Low Level Input Range: Lowest Recommend Load: Typical Efficiency: Damping Factor: Ti1500.1 Dynamic Power 14.4Vdc >1% THD RMS Power 14.
PAGE 3
Amplifier Owner’s Manual ti2500.1 - ti1500.1 Monoblock Power Amplifier INPUT Connect preamp signal cables from the head unit to these terminals. OUTPUT Provides a full range signal for an additional amplifier. There is no signal loss if using this output. CROSSOVER FREQUENCY Controls the lowpass crossover point for the speaker outputs. BASS BOOST Variable bass boost from 0 to +18dB @ 45 Hz. LOW PASS LEVEL CONTROL (LPL) This port is for connecting the optional remote level control (LPL44).
PAGE 4
Amplifier Owner’s Manual ti800.4 - ti600.4 4 Channel Power Amplifier INPUT Connect preamp signal cables from the head unit to these terminals. CROSSOVER FREQUENCY Controls the crossover point for the speaker outputs. BASS BOOST Variable bass boost from 0 to +18dB @ 45 Hz. 2ch/4ch MODE LOW PASS LEVEL CONTROL (LPL) This port is for connecting the optional remote level control (LPL44). This allows up to 20dB of volume adjustment.
PAGE 5
Amplifier Owner’s Manual Crossover Settings All crossover frequency potentiometers have 41 detents or “clicks” so the end user can set the exact cross over frequency desired. No more turning the potentiometer and guessing where your crossover points are. You get exact control of your amplifier’s output. Ti2500.1 - Ti1500.1 Ti800.4 - Ti600.4 clicks HP (20~400hz) LP (40~400Hz) Bass Boost 0.0 1 434 434 0.1 0.0 2 433 432 0.1 313 0.0 3 427 415 0.3 52 313 0.0 4 416 385 0.
PAGE 6
Amplifier Owner’s Manual How to strap two monoblocks Strapping or linking two Ti amplifiers allows you to deliver a ton of power into a single voice coil commonly used in SPL competitions. The example below shows two Ti1500.1s delivering a total of 3000 watts into a single 2 ohm voice coil. DO NOT STRAP AMPLIFIERS INTO A 1 OHM LOAD. NOTES: The “Master” amplifier’s preamp section controls both amplifiers. “Slave” amplifier’s pre-amp control are disabled. Min Load is 2 ohm when strapped.
PAGE 7
Manuel de l’amplificateur Spécifications CARACTÉRISTIQUES TECHNIQUES MONOBLOC Réponse en fréquence : Rapport signal/bruit : Filtres passifs subsoniques et passe-bas: Plage du filtre passif passe-bas: Plage du filtre passif subsonique: Amplification des basses à 45 Hz : Gamme d’entrée de niveau faible: Charge minimale recommandée: Efficacité type: Taux d’amortissement: ± 1 dB de 20 Hz à 300Hz >90dB 24dB par octave 30Hz à 300Hz 10Hz à 55Hz 0 à +18dB 200 millivolts à 8 volts 1 ohm 80% Supérieur à 200 Ti150
PAGE 8
Manuel de l’amplificateur ti2500.1 - ti1500.1 Monoblock Power Amplifier ENTRÉE ENTRÉE DE L’AFFICHAGE DE TENSION A DISTANCE (RMD) Reliez les câbles de signal préampli de l’unité principale sur ces bornes. Connectez le RMD d’affichage de tension facultatif à cette prise jack. SORTIE GAIN NIVEAU Fournit un signal pleine gamme pour un amplificateur supplémentaire. Il n’y a pas de perte de signal en cas d’utilisation de cette sortie.
PAGE 9
Manuel de l’amplificateur ti800.4 - ti600.4 4 Channel Power Amplifier ENTRÉE Reliez les câbles de signal préampli de l’unité principale sur ces bornes. FRÉQUENCE DE FILTRE PASSIF PASSE-BAS et PASSEHAUT Contrôle les points de filtre pour les sorties du haut-parleur. COMMANDE À DISTANCE DU NIVEAU DES BASSES (LPL) Ce port sert à connecter la télécommande de niveau optionnelle (LPL44). Cela permet un ajustement du volume allant jusqu’à 20 dB.
PAGE 10
Manuel de l’amplificateur Réglages du filtre passif Ti2500.1 - Ti1500.1 Ti800.4 - Ti600.4 clicks HP (20~400hz) LP (40~400Hz) Bass Boost 0.0 1 434 434 0.1 0.0 2 433 432 0.1 313 0.0 3 427 415 0.3 52 313 0.0 4 416 385 0.6 5 52 289 0.2 5 404 361 0.9 6 48 289 0.4 6 392 343 1.3 7 48 268 0.6 7 382 325 1.7 8 48 268 0.7 8 371 309 2.0 9 48 247 0.9 9 362 295 2.4 10 48 247 1.0 10 353 283 2.7 11 44 229 1.1 11 336 275 3.1 1.
PAGE 11
Manuel de l’amplificateur Comment sangle deux monoblocs AUTORADIO MASTER + CABLE RCA PRINCIPAL - Relier ensemble les bornes haut-parleur négatives (-) des amplificateurs. PAS UTILIZE SLAVE © 2010 Phoenix Gold • www.phoenixgold.com phoenix gold ti amp manual.
PAGE 12
Phoenix Gold A Division of AAMP of America™ 13190 56th Court Clearwater, Florida 33760 P: 888-228-5560 info@phoenixgold.com www.phoenixgold.com © 2010 AAMP of Florida, Inc Designed and Engineered in the USA Phoenix Gold Product Warranty LIMITED WARRANTY ON AMPLIFIERS Phoenix Gold warrants this product to be free of defects in materials and workmanship for a period of one (1) years from the original date of purchase.