www.phoenixgold.
I N T R O D U C T I O N Congratulations on purchasing one of the finest amplifiers available in the car audio marketplace today. The Xenon amplifiers were designed and engineered with the spirit of the original Phoenix Gold MS and M series to deliver bulletproof performance at any impedance while delivering unbelievable sound quality. Cosmetics: C i r c u i t To p o l o g y : Reliability: Exotic sports cars were used for styling inspiration.
M O N O B L O C K S P E C I F I C AT I O N S Frequency Response: . . . . . . . . . . . . . .± 1dB from 20Hz to 300Hz Signal to Noise Ratio: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>90dB Subsonic and Low Pass Crossovers: . . Linkwitz-Riley 24dB per octave X400.1 Into 4, 2 and 1 ohm . . . . . . . . . .400 x 1 Recommended Fuse Size: . . . . . . . .40A Power/Ground Wire Size . . . . . .8 Gauge Dimensions: . . . . .14L x 10.6W x 2.5H Low Pass Crossover Range: . . . . . . . . . . . . . . . . .
M O N O B LO C K S 4 RMD L R INPUT Speaker Outputs RMD INPUTS Used to connect the amplifier to speakers. The separate + and – terminals are internally wired in parallel. Minimum speaker cable size is 12 gauge. Lowest recommend impedance is 1 ohm. Remote Voltage Display Input Connect the optional RMD Voltage Display to this jack. Connect preamp signal cables from the head unit to these terminals. To maximize noise rejection, we recommend using Phoenix Gold ARx.800, ARx.700, ARx.600 or ARx.
R LPL B www.phoenixgold.
C H A N N E L T W O L 6 L R R RMD L BRIDGED R INPUT Speaker Outputs RMD INPUTS Used to connect the amplifier to speakers. Use the left + and right – terminals for bridged mode. Minimum speaker cable size is 16 gauge. Use 12 Gauge for bridged operation. Minimum impedance is 2 ohm bridged or 1 ohm stereo. Remote Voltage Display Input Connect the optional RMD Voltage Display to this jack. Connect preamp signal cables from the head unit to these terminals.
C H A N N E L R LPL B R B T W O L AUX OUTPUT AUX OUTPUT B+ R B– B+ This must be connected to the fused positive terminal (+12V) of the car’s battery. X100.2 = 8 Gauge X200.2 = 4 Gauge REMOTE This must be connected to switched +12V, usually a trigger wire coming from the head unit or ignition. B– This must be connected to the negative terminal (–12V) of the car’s battery. X100.2 = 8 Gauge X200.2 = 4 Gauge www.phoenixgold.
C H A N N E L F INPUT R 2CH-4CH F O U R L R R RMD BRIDGED L R FRONT Speaker Outputs Input RMD INPUTS Used to connect the amplifier to speakers. Use the left + and right – terminals for bridged mode. Minimum speaker cable size is 16 gauge. Use 12 Gauge for bridged operation. Minimum impedance is 2 ohm bridged or 1 ohm stereo. OUT: The Rear input of the amplifier is used to provide signal for the rear channels. This allows separate front and rear inputs for use with a headunit fader.
C H A N N E L R L R LPL B R B F O U R AR AUX OUTPUT AUX OUTPUT LPL44 PORT Provides a full range signal for an additional amplifier. This port is for connecting the optional LPL44™ Remote Lowpass Level Control knob allowing up to 20dB of volume adjustment. The LPL44 will only work when the lowpass crossover is on. B+ R B– B+ This must be connected to fused the positive terminal (+12V) of the car’s battery. X200.4, X100.
I N S TA L L AT I O N 10 www.phoenixgold.
Phoenix Gold International, Inc. (or "Phoenix Gold") warrants its products against defects in materials and workmanship for a limited period of time. For a period of 90 days from date of original purchase, we will repair or replace the product, at our option, without charge for parts and labor. Customer must pay all parts and labor charges after the limited warranty period expires. The limited warranty period for factory refurbished products expires after ninety (90) days from date of original purchase.
PHOENIX GOLD INTERNATIONAL, Inc. 9300 North Decatur Portland, OR 97203 Tel: 503.286.9300 Fax: 503.978.3380 www.phoenixgold.com www.phoenixgold.
