BTL Td oa lees NT INSTRUCTION E CORNING TH bipippebHL ilia Control throw Ailerons: Low: 13mm up/down, 10% expo; High: 16mm up/down, 10% expo SPECIFICATION | Control throw Elevators: Low: 13mm up/down, Wingspan: 1772mm (69.72in) 12% expo; High: 16mm up/down, 12% expo Length: 2019mm (79.5 in) Control throw Rudder: Low: 30mm rightful Flying weight: expo; High: 40mm weightlifter, 15% expo Wing area: 57.
INSTRUCTION MANUAL TABLE OF CONTENTS Introduction 1 Installing the rudder push rod 21 MILITANTLY Irene 2 Installing the elevator push rod 24 Disclaimer... Installing the nose gear retract 26 Safety precaution Electric retract system. 28 Important building notes... 2 Installing the engine 29 Suggestion...
INSTRUCTION MANUAL WARRANTY Phoenix Model guarantees the component parts in this kit to be free from defects in both material and workmanship at the date of purchase by the purchaser. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product. This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than Phoenix Model.
FLIGHT WARNINGS * When ready to fly, first extend the transmitter aerial. * Switch on the transmitter. * Switch on the receiver. * Check that the wings are correctly fitted to the fuselage. * Operate the control sticks on the transmitter and check that the control surfaces move freely and in the CORRECT directions. * Check that the transmitter batteries have adequate power. * ALWAYS take off into the wind.
+ Officially designated AMA Air Show Teams (AST) are authorized to use devices and practices as defined within the Team AMA Program Document. (AMA Document #718.) {i} Not operate a turbine-powered aircraft, unless in compliance with the AMA turbine regulations. (AMA Document #510-A) 3.
INSTRUCTION MANUAL INSTALLING THE LIGHT WING < Trim the plastic cover > 2 x 5mm TP Screw 2x5mm A Apply instant glue light wing < Left Wing > < Top view > < Green light > Cs Stern, * pm, Must be purchased separately! Assemble left and right A sides the same way Apply instant glue 2 (CA glue, super glue).
INSTRUCTION MANUAL PREPARATIONS Use a covering iron with a covering sock on high heat to tighten the covering if necessary. Apply pressure over sheered areas to thoroughly bond the covering to the wood. wy Assemble left and right "AS sides the same way INSTALLING THE AILERONS AND FLAPS /N WARNINGS < RIGHT > Aileron Maltese Aileron 3x15mm \ A > Please note that C.
INSTRUCTION MANUAL Main Wing Aileron » Make certain the hinges are adequately secured with glue. If they come loose in flight accidents may result. LA Assemble left and right = "43 sides the same way 2 Cut off shaded portion Ensure smooth, non-binding [A]n] wi Apply epoxy glue.
A > Set all screws securely.
< Top view > 3x16mm Hom A Please note that C.A glue must be apply to these holes before screw the control hom to the fiat. If not, it Tomes off during flights, you may lose control of your airplane, resulting in an accident ! 3x10mm Apply instant glue 1 (CA glue, super glue). Cut off shaded portion L4 Assemble left and right "4 sides the same way Ell Drill holes with the pacified diameter.
INSTRUCTION 2x 10mm TP Screw Must be purchased separately! wy Assemble left and right "AS sides the same way
INSTRUCTION MANUAL INSTALLING THE PLASTIC COVER Plastic cover Cut off shaded portion 2] Apply instant glue 4 Assemble left and right (CA slug, super gust.
INSTRUCTION MANUAL Cut off shaded portion Assemble left and right "43 sides the same way 4 IY] Apply epoxy glue
INSTRUCTION MANUAL < Right Wing > < Left Wing > s N ELECTRIC RETRACT SYSTEM Main Whee! (NT) Power led = (Powered or Front / Back Wheel oO I POWER 7 4v NYY Controller Box H Receiver Lor) © J] no Main Wheel Q > le—) Handle J Assemble left and right LA] sides the same way
INSTRUCTION MANUAL SECURE THE FUSELAGE 4 x 20mm Cap Screw SECURE THE WING TO THE FUSELAGE . THEY HAVE 2 OPTION FOR SECURING. ( . Option 1 6mm Plastic Screw =H Tm 4 Assemble left and right J sides the same way.
INSTRUCTION MANUAL Aluminum 4 x 15mm Cap Screw \Assemble left and right ; A sides the same way.
INSTRUCTION MANUAL Assemble left and right \_ BH sides the same way. 0 Main wing must be Inserted and attached completely before fixing with screw. Cap screw for main wing fixture HORIZONTAL STABILIZER INSTALLATION 1. Using a modeling knife, cut away the covering from the fuselage for the stabilizer and remove it. 2. Remove the covering from the stabilizer. When cutting through the covering to remove if, cut with only enough pressure to only cut through the covering it's eff.
INSTRUCTION MANUAL » Make certain plane Is aligned accurately per the diagram. Amos-aligned plane can fly erratically and cause accidents. Lgl Assemble left and right 0 Secure nylon hinges with instant glue, being "43 sides the same way. a Cut off shaded portion careful horizontal fin and elevator. -bind Ensure smooth, non-binding 5 Apply epoxy glue a Align the center line of horizontal fin with elevator. movement when assembling.
INSTRUCTION MANUAL RUDDER INSTALLATION Ensure smooth, non-binding movement when assembling. 20 RY Apply epoxy glue =] » Take off the main wing after put a rudder.
INSTRUCTION MANUAL Cut off shaded parson 2] Apply Instant glue Lg Assemble left and right (CA glue, super glue). "4 sides the same way.
INSTRUCTION MANUAL Open and close Set all screws securely. If they come off during flight you will lose control of your aircraft! Rudder Serve Mark the spot to attach. Cut off shaded portion 3 Pay close attention here Must be purchased separately! Cut off excess.
INSTRUCTION MANUAL INSTALLING THE ELEVATOR PUSH ROD ¥ 3 x 20mm Cap Screw (mmm 2 x 10mm Cap Screw Cut off shaded portion Assemble left and right LA tildes the same way.
INSTRUCTION Elevator Servo Elevator Servo £3 Mark the spot to attach. Cut off shaded portion a Pay clods attention here Must be purchased separately! Cut off excess.
INSTRUCTION MANUAL Open and close Apply instant glue El (CA glue, super glue).
INSTRUCTION MANUAL Aluminum ball Cut off excess. 's N ELECTRIC RETRACT SYSTEM Main Wheel 5 5 Power led ovo Le ~e) Front / Back Wheel J POWER Controller Box Screwdriver oro) © nN Main Wheel = ee AAA vv vol lo—2¢) Handle \.
INSTRUCTION MANUAL INSTALLING THE ENGINE May be you also need to trim some wood from the tree-angle wood for the Installation installing the engine mount for DLE-35CC or OS-33GT. Using plate of plywood (supplied with the kit) mark the holes onto the fire wall for Is easy.
INSTRUCTION MANUAL #1 {3x 15mm TP Screw 1 Assemble loft and right "43 sides the same way [All Drill holes with the specified diameter. 2 Apply instant glue {CA glue, super glue).
INSTRUCTION MANUAL INSTALLING THE FUEL TANK Fuse Tank 500cc < Front View > Fuse Tank < Top View > 188.0 146.0 64.
INSTRUCTION MANUAL Fuel Tank INSTALLING THE THROTTLE 1. Plug the throttle servo into the receiver and tum on the radio system. Check to ensure that the throttle servo output shaft is moving in the comet direction. When the throttle stick is moved forward from idle to full throttle, the throttle barrel should also open and close using this motion. If not, reverse the direction of the serve, using the transmitter.
INSTRUCTION MANUAL Apply Instant glue C1 (CA glue, super glue). £3 Adjust the throttle input (transmitter throttle stick), throttle trim movement and the carburetor opening to the suitable position and screw in the 4x4mm set screw. MOUNTING THE COWL 1. Remove the muffler and needle valve assembly from the engine. Slide the fiberglass cowl over the engine. 2. Measure and mark the locations to be cut out for engine head clearance, needs valve, muffler.
INSTRUCTION MANUAL Trim the cowling so it will match your engine Cut off shaded portion A Apply instant glue (CA glue, super glue). Assemble left and right Le slides the same way. [Al Drill holes with the specified diameter.
INSTRUCTION MANUAL INSTALLING THE SPINNER AN Install the spinner back-plate, propeller and spinner cone. > Securely tighten the nut holding the propeller for it not come off wham the motor is spinning. If coming off, there is a high risk of The propeller should not touch any part of the injury! spinner cone. If it dose, use a sharp modeling > Always ensure propeller and spinner ars balanced.
INSTRUCTION MANUAL Throttle hole ® 10mm Throttle hole @ 10mm 4 x 50mm Cap Screw 4mm Nut me ge 8 4mm Washer 4mm Mount Nut 4mm Spring Washer 1.
7 Throttle Servo Cut off shaded portion Es.00 2s.
INSTRUCTION MANUAL INSTALLING THE RECEIVER AND BATTERY 1. Plug the servo leads and the switch lead into the receiver. You may want to plug an aileron extension into the receiver to make plugging in the aileron servo lead easier when you are installing the wing. Plug the battery pack lead into the switch. 2. Wrap the receiver and battery pack in the protective foam to protect them from vibration. Use a rubber band or masking tape to hold the foam in place.
INSTRUCTION MANUAL 1. It is critical that your airplane be balanced correctly. Improper balance will cause your plane to lose control and crash. THE CENTER OF GRAVITY IS LOCATED 169mm (6.65 in) BACK FROM THE LEADING EDGE OF THE WING, AT THE FUSELAGE. BALANCE A PLANE UPSIDE DOWN WITH THE FUEL TANK EMPTY. 2. If the nose of the plane falls, the plane is nose heavy. To correct this first move the battery pack further back in the fuselage.
INSTRUCTION MANUAL =] » In order to obtain the CG specified, reposition the receiver and other equipment. » If not obtain the CG specified, add a weight and adjust. LATERAL BALANCE After you have balanced a plane on the C.G. You should laterally balance it. Doing this will help the airplane frack straighter. 1. Tum the airplane upside down. Attach one loop of heavy string to the engine crankshaft and one to the tail wheel wire. With the wings level, carefully lift the airplane by the string.
INSTRUCTION MANUAL 4 CHANNEL RADIO SETUP (STANDARD MODE EMPEROR MOVES DOWN A EO 3.5 FLIGHT PREPARATION PRE FLIGHT CHECK 1. Completely charge your transmitter and receiver batteries before your first day of flying. 2. Check every bolt and every glue joint in your plane to ensure that everything is tight and well bonded. 3. Doubles check the balances of the airplane 4. Check the control surface 5. Check the receiver antenna . It should be fully extended and not coiled up inside the fuselage. 6.