AURORA GP/EP size 46-55 ARF ell ee al h Taf ct Ion igh Lis iid Steely 5 CONE/ nd pid Control throw Ailerons: Low: 9mm up/down, 10% expo; High: 12mm up/down, 10% expo Control throw Elevators: Low: 9mm up/down, 12% expo; High: 12mm up/down, 12% expo Control throw Rudder: Low: 20mm right/left, 15% expo; High: 30mm right/left, 15% expo Experience level: Intermediate Plane type: Low wing sport f3a RECOMMENDED MOTOR AND BATTERY SET UP Motor: RIM FIRE (not included) Lip cell: 6 cells / 4000 — 5500mAh (not included
INSTRUCTION MANUAL pr rf n=] Introduction 1 MILITANTLY coven Erie 2 Disclaimer... Safety precaution Important building notes 2 2 Flight 2 Flight 3 Covering 3 Adhesives and required tools 3 Academy of model aeronautics national model aircraft safety 3 Painting the firewall 5 5 Installing the ailerons 5 Installing the aileron servos 7 Installing the control horns 7 Installing the aileron linkages 8 Installing the plastic 9 Installing the main landing gear .
INSTRUCTION MANUAL WARRANTY Phoenix Model guarantees the component parts in this kit to be free from defects in both material and workmanship at the date of purchase by the purchaser. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product. This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than Phoenix Model.
INSTRUCTION MANUAL When ready to fly, first extend the transmitter aerial. * Switch on the transmitter. + Switch on the receiver. » Check that the wings are correctly fitted to the fuselage. * Operate the control sticks on the transmitter and check that the control surfaces move freely and in the CORRECT directions. * Check that the transmitter batteries have adequate power. * ALWAYS take off into the wind.
INSTRUCTION MANUAL « Officially designated AMA Air Show Teams (AST) are authorized to uss devices and practices as defined within the Team AMA Program Document. (AMA Document #718.) {i} Not operate a turbine-powered aircraft, unless in compliance with the AMA turbine regulations. (AMA Document #510-A) 3.
INSTRUCTION MANUAL Use a covering iron with a covering sock on high heat to tighten the covering if necessary. Apply pressure over sheered areas to thoroughly bond the covering to the wood. PAINTING THE FIREWALL prevent gasoline from seeping into the wood, the modeler have to paint the paint on the surface of the wood as shown in the drawing. Paintbrush \. J PREPARATIONS INSTALLING THE AILERONS 1. Test fit the ailerons to the wing with the hinges.
INSTRUCTION MANUAL \ /N WARNINGS \ » Please note that C A glue must be apply to these holes before screw the control hom to the aileron. If not, it comes off during flights, you Q may lose control of your airplane, resulting in an accident § ) Main Wing < Bottom view > > Make certain the hinges are f adequately secured with glue. L If they come loose in flight Aileron accidents may result.
INSTRUCTION MANUAL INSTALLING THE AILERONS SERVOS 1. Install the rubber grommets and brass eyelets onto the aileron servo. 2. Using a modeling knife, remove the covering from over the per-cut servo am exit hole on the aileron servo tray / hatch. This hole will allow the servo am to pass through when installing the aileron push rods. 3. Place the servo into the servo tray.
INSTRUCTION MANUAL INSTALLING THE AILERONS LINKAGES Control hom 0 3 x 10mm Button Screw 0 3x10mm QQ 2 Aluminum ball 0 eo 24 Aluminum ball 3mm Silicone | ny < Bottom view > Assemble left and right A sides the same way < Bottom view > Silicone Assemble left and right = sides the same way ® Wiki link 8
INSTRUCTION MANUAL INSTALLING THE PLASTIC COVER Plastic cover » Do not overlook this symbol! EH Apply Instant glue 4} (CA glue, super glue). Cut off shaded portion 4 Assemble left and right "41 sides the same way INSTALLING THE MAIN LANDING GEAR 3 x 12mm TP Screw eee 8 Nep — . Collar — .
INSTRUCTION MANUAL Apply threadlike {screw cement}. 4 Assemble left and right "4d sides the same way INSTALLING THE WING TO THE FUSELAGE Attach the wings to the joiner tube and secure the wing panels to the fuselage. © Cap screw for main wing Thurs © Main wing must be inserted and attached completely before fixing with screw. Cut off shaded portion LA Assemble left and right "43 sides the same way.
INSTRUCTION MANUAL HORIZONTAL STABILIZER INSTALLATION 6. When you are sure that everything is aligned -— correctly, mix up a generous amount of 30 minute 1. Using a modeling knife, cut away the covering epoxy. Apply a thin layer to the top and bottom of from the fuselage for the stabilizer and remove it. the stabilizer mounting area and to the stabilizer | | mn mounting platform sides in the fuselage. Slide 2. Draw a center line onto the horizontal stabilizer. the stabilizer in place and re-align.
INSTRUCTION MANUAL Cut off shaded portion Apply instant glue 1 (Callus, super glue) H Ensure smooth, non-binding movement when assembling
INSTRUCTION MANUAL INSTALLING THE RUDDER PUSH ROD 1. Locate the push rod exit slot on the left side of the fuselage. 2. Carefully cut away the covering material from the slot. 3. Working from inside the fuselage, slide the threaded end of the remaining push rod down the inside of the fuselage until the push rod reaches the exit slot. Carefully reach in with a small screw driver and guide the push rod out of the exit slot. 4. Install the clevis on the rudder push rod.
INSTRUCTION MANUAL approx. 13mm Cm 19°] Rudder Servo 6mm Side view. > = Pay close attention Cut off excess. Cut off shaded portion [a Drill holes with the Must be purchased separately! (zen] specified diameter. £3 Cut away fim only. here. {3 Use this hale INSTALLING THE ELEVATOR PUSH ROD 1. Locate the push rod exit slot on the right side and left side of the fuselage. It is located slightly ahead and below the horizontal stabilizer. 2. Carefully cut away the covering material from the slot. 3.
INSTRUCTION MANUAL 7. Attach clevis to the third hole in the control horn. 2x 16mm TP Screw (Rene 4 8. Connect the two elevator push rod using the domino. Domino 9. Locate one nylon servo arm, and using wire cutters, remove all but one of the arms. Using a 2mm drt | Yl) 1 bit, enlarge the third hole out from the center to accommodate the elevator push rod wire. 1.7 x 100mm Push rod — 10. Plug the elevator servo into the receiver and center ~~ | cee 1 the servo. Install the servo arm onto the serve.
INSTRUCTION MANUAL < Bottom view.> < Right side view.> approx. 13mm Set all screws securely. If they come off during flight you will lose control of your aircraft 4 Z | Elevator Servo rr Cm Must be purchased cy separately! AK Cut off excess.
INSTRUCTION MANUAL INSTALLING THE ENGINE MOUNT 4 x 25mm Cap Screw (mmm 4mm Washer 4mm Mount Nut Apply thread locker (screw cement).
INSTRUCTION MANUAL NN Do not overheat, it may break. 2 Cut off shaded portion INSTALLING THE FUEL TANK 1. Using a modeling knife, cut one length of silicon fuel line (the length of silicon fuel line is calculated by how the weighted clunk should rest about 5mm away from the rear of the tank and move freely inside the tank). Connect one end of the line to the weighted clunk and the other end to the nylon pick up tube in the stopper. 2.
INSTRUCTION Foam ring 3 Refer to engine's Instruction manual and set up piping. INSTALLING THE THROTTLE PUSH ROD SERVO 1. Place the engine into the engine mount and align it properly with the front of the cowling. If your engine is equipped with a remote needle valve, we suggest installing it into the engine at this time. 2. Slide the push rod housing through the hole in the firewall, through the hole in the forward bulkhead, and into the servo compartment. .
INSTRUCTION MANUAL Throttle red » Temporarily install the engine and make a hole for the throttle rod by aligning with the position of the throttle lever. Cio PP Pipe \ Ml Apply epoxy glue INSTALLING THE ENGINE Zorro roa | [3x 26mm Gap Sower Locate the long piece of wire used for the throttle EL a— push rod. One end of the wire has been per-bsnd : 1 Ef mmm bend at the factory.
INSTRUCTION MANUAL Must be purchased separately! INSTALLING THE THROTTLE 1. Install one adjustable metal connector through the third hole out from the center of one servo arm, enlarge the hole in the servo am using a 2mm drill bit to accommodate the servo connector. Remove the excess material from the arm. After installing the adjustable metal connector apply a small drop of thin C/A to the bottom nut. This will prevent the connector from loosening during flight. 2.
INSTRUCTION £3 Adjust the throttle Input (transmitter throttle stick), throttle trim movement and the carburetor opening to the suitable position and screw in the 4x4mm set screw. < Throttle ding > Throttler Servo Pipe | Apply thread locker (screw cement). Ensure smooth, non-binding movement when assembling Must be purchased separately! MOUNTING THE COWL 1. Remove the muffler and needle valve assembly from the engine. Slide the fiberglass cow! over the engine. 2.
INSTRUCTION MANUAL 3x 10mm TP Screw (omega es 4 Cut off shaded portion = Assemble left and right 2 Apply Instant glue sides the same way. [1 (CA slug, super glucose.
INSTRUCTION MANUAL INSTALLING THE SPINNER Install the spinner back-plate, propeller and spinner cone. The propeller should not ouch any part of the spinner cone. If it dose, use a sharp modeling knife and carefully trim away the spinner cone where the propeller comes in contact with it. 3x12mm TP Screw Propeller = Securely tighten the nut holding the propeller for it not come off ‘wham the motor Is spinning. If coming off, there Is a high Hsk of Injury > Always ensure propeller and spinner are balanced.
INSTRUCTION MANUAL Tape Foam Pad Battery Tape Foam Pad — : IN... p= Attach securely. Must be purchased Disconnection during flight will cause loss sarsaparilla of control and may result in an accident INSTALLING THE ELECTRIC MOTOR 4 x 16mm Cap Screw 4 x 60mm Cap Screw 4x16mm: A White glue 4x16mm Apply threadlike (screw cement).
INSTRUCTION MANUAL Electric Speed Controller Must be purchased separately! a3 Fallow instruction manual of Motor and ESC. When rotating clock wise, change the connection of 2 wires.
INSTRUCTION MANUAL 1. It is critical that your airplane be balanced correctly. Improper balance will cause your plane to lose control and crash. THE CENTER OF GRAVITY IS LOCATED 125mm {4.9 in) BACK FROM THE LEADING EDGE OF THE WING, AT THE FUSELAGE. BALANCE A PLANE UPSIDE DOWN WITH THE FUEL TANK EMPTY. If the nose of the plane falls, the plane is nose heavy. To correct this first move the battery pack further back in the fuselage.
INSTRUCTION MANUAL 4 CHANNEL RADIO SETUP (STANDARD MODE EEA LEMON MOVES Daw FLIGHT PREPARATION PRE FLIGHT CHECK 1. Completely charge your transmitter and receiver batteries before your first day of flying. 2. Check every bolt and every glue joint in your plane to ensure that everything is tight and well bonded. 3. Double check the balance of the airplane. Check the control surface. 5. Check the receiver antenna. It should be fully extended and not coiled up inside the fuselage. 6.
INSTRUCTION MANUAL DECORATION < Bottom view > < Top view > < Side view > < Side view > #023 Ferrari Red #024 Pink #019 Corsair Blue #053 Sky Blue #092 Gold #011 Grey #010 White 31
