Instruction Manual hh PHOENIX MODEL” EXTRA 260 GP/EP Size 30/33cc Scale 1:3 % ARF SPECIFICATION Engine: 30-35¢c gas engine {not included) Wingspan: 2000mm (78.7 in} Gator: brush less out runner 2500 W, Length: 1848mm (72.7 in} 250 KV {not included) Flying weight: 5700-5800 gr Gravity CG: 160-165 mm in) Back from Wing area: 79.
INSTRUCTION MANUAL pr rf nS] Introduction 1 MILITANTLY Irene 2 Disclaimer... Safety precaution Important building 2 2 Flight 2 Flight 3 Covering tools... 3 Adhesives and required tools 3 Academy of model aeronautics national Model aircraft safety 3 Suggestion for engine and servo 5 Preparations 5 Installing the ailerons 5 Installing the ailerons servos 6 Installing the aileron linkages 8 Installing the main landing gear 10 Secure the wing to the 13 Horizontal stabilizer installation .
INSTRUCTION MANUAL Lag Phoenix Model guarantees the component parts in this kit to be free from defects in both material and workmanship at the date of purchase by the purchaser. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product. This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than Phoenix Model.
INSTRUCTION MANUAL LEX AL « When ready to fly, first extend the transmitter aerial. © Switch on the transmitter. « Switch on the receiver. * Check that the wings are correctly fitted to the fuselage. * Operate the control sticks on the transmitter and check that the control surfaces move freely and in the CORRECT directions. * Check that the transmitter batteries have adequate power. * ALWAYS take off into the wind.
INSTRUCTION MANUAL + Officially designated AMA Air Show Teams (AST) are authorized to use devices and practices as defined within the Team AMA Program Document. (AMA Document #718.) {i} Not operate a turbine-powered aircraft, unless in compliance with the AMA turbine regulations. (AMA Document #510-A) 3.
INSTRUCTION MANUAL SUGGESTION FOR ENGINE AND SERVO + ENGINE: DLE 35 RA; OS 33GT + SERVO: Two Options « Servo Option spotter Performance Hittite 7985MG Servos may be used for sport flying. * § Hittite 7985MG Servos for flight surfaces * 1 Hittite 5625MG Servo for throttle « Servo Option 2: Unlimited Performance Hittite 79548TH Servos are recommended for unlimited flying.
INSTRUCTION MANUAL A P= Make certain the hinges are adequately secured with glue. If they cons loos in flight accidents may result. RY] Apply epoxy glue INSTALLING THE AILERONS SERVOS 1. Install the rubber grommets and brass eyelets onto 4. Using the thread as a guide and using masking the aileron servo. tape, tape the serve lead to the end of the thread: carefully pull the thread out. When you 2. Using a modeling knife, remove the covering from over have pulled To Pn lead out, remove the the servo box.
INSTRUCTION MANUAL aileron servo > Aileron A > Set all scores socially. If they come off during flight you will lose control of your aircraft! 4 Must be purchased separately! {3 Pull out servo 4 Assemble left and right cord with string. "43 sides the same way {© Tie the string.
INSTRUCTION MANUAL INSTALLING THE AILERON LINKAGES 4. 1. Install the control hom inch the aileron. 2. Locate the metal rod wire, screw the plastic link ball onto the threaded end of the wire. 3. Plug the aileron servo into the receiver and center Center the aileron and hold it in place using a couple of pieces of masking tape. Adjust the linkage until the aileron and the servo arm are both centered and then tighten the nut against. Remember use thread locking compound to secure. the servo.
INSTRUCTION MANUAL INSTALLING THE MAIN LANDING GEAR 8mm Nut ef 4mm Collar ® 8mm Washer 4 x 30mm Cap Screw (mmm. < Main Gear (R) > (fmm Out view : In view : Front view LA Perspective view 4 Assemble left and right "43 sides the same way Bottom view Top view FEA Apply Instant glue {CA glue, super glue}.
INSTRUCTION MANUAL Main gear Main gear Whee! Pant 85mm Wheaties Wheel Pant Washer Collar Apply thread locker {screw cement).
INSTRUCTION MANUAL SECURE THE WING TO THE FUSELAGE 6mm Plastic Screw Attach the wings to the fuselage and secure the wing panels.
INSTRUCTION MANUAL 4mm Plastic Screw Assemble left and right sides the same way Cut off shaded portion HORIZONTAL STABILIZER INSTALLATION §. When you are sure that everything is aligned correctly, mix up a generous amount of 30 minute epoxy. Apply a thin layer to the bottom and to the top of the stabilizer mounting area and to the stabilizer mounting platform sides in the fuselage. Insert the stabilizer in place and re-align. Double check all of your measurements one more time 1.
INSTRUCTION MANUAL RUDDER INSTALLATION Cut off shaded portion mW Apply epoxy glue INSTALLING THE RUDDER LINKAGES The rudder is controlled by two metal cables. Install the rudder linkages and cables as below. 1. Use a hobby knife to remove the covering from the openings for the rudder control cables. 2. The rudder has a block wood plate for mounting the control hom. Twe control hom in positioned on both side rudder (left and right). 3. Install the control hom to the rudder. 4.
INSTRUCTION MANUAL © Aluminum ball <% 3mm—, ~~ Cabs red Cut off shaded portion Must be purchased separately! Aa Pay close attention here 3x36mm
INSTRUCTION MANUAL INSTALLING THE ELEVATOR SERVO INSTALLING THE ELEVATOR LINKAGES 1. Rome ve the covering from both size of the . Repeat these step as installing the aileron fuselage. linkages. 2. Install two servo to the fuselage as shown. 3. Repeat these step as installing the aileron control hom.
INSTRUCTION MANUAL Must be purchased separately! Assemble left and right A sides the same way A Pay close attention here
INSTRUCTION MANUAL Assemble left and right LA sides the same way INSTALLING THE TAIL WHEEL #2-Tail wheel set 4x 15mm Gap Screw Pee , 0 Cut off shaded portion
INSTRUCTION MANUAL INSTALLING THE ENGINE Using plate of plywood (supplied with the kit) mark the holes root the fire wall for installing the engine mount for DLE-35CC or 0S-33GT. Oo 08 33CC om O OR May be you also need to im some wood from the triangle wood for the installation is easy.
INSTRUCTION MANUAL 5x 100mm Cap Screw 5mm Washer ee G ESO Stone DLE35CC Metal wiki link (M2) 2 Silicons Qo 2 H Apply thread locker (screw cement). DLE 35CC — Must be purchased \ separately!
INSTRUCTION MANUAL \ Do not overheat, it may break. 8mm Cut off shaded portion INSTALLING THE FUEL TANK 5. When satisfied with the alignment of the stopper 1. Using a modeling knife, cut one length of silicon fuel line {the length of silicon fuel line is calculated by how the weighted clunk should rest about 5mm away from the rear of the tank and move freely inside the tank). Connect one end of the line to the weighted clunk and the other end to the nylon pick up tube in the stopper. 2.
INSTRUCTION MANUAL Fuse Tank INSTALLING THE THROTTLE 1. Plug the throttle servo into the receiver and tum on the radio system. Check to ensure that the throttle servo output shaft is moving in the correct direction. When the throttle stick is moved forward from idle to full throttle, the throttle barrel should also open and close using this motion. If not, reverse the direction of the servo, using the transmitter.
INSTRUCTION MANUAL Throttle Serve Must be purchased separately! MOUNTING THE COWL 1. Remove the muffler and needle valve assembly from the engine. Slide the fiberglass cowl over the engine. . Measure and mark the locations to be cut out for engine head clearance, needle valve, muffler. Remove the cowl and make these cutouts using a rotary tool with a cutting disc and a rotary sanding drum attachment. . Slide the cowl back into place. Align the front of the cowl! with the crankshaft of the engine.
INSTRUCTION MANUAL 3x 15mm TP Screw { eee £3 Trim the cowling so it will match your engine xterm Cut off shaded portion 2] Apply instant glue (CA glue, super glue). Lg] Assemble left and right iN sides the same way.
INSTRUCTION MANUAL INSTALLING THE SPINNER Install the spinner back-plate, propeller and spinner cone. The propeller should not ouch any part of the spinner cone. If it dose, use a sharp modeling knife and carefully trim away the spinner cone where the propeller comes in contact with it. 3x 12mm TP Screw (Joan Propeller Spinner 3x12mm Spinner A = Securely tighten the nut holding the propeller for it not come off when the motor Is spinning.
INSTRUCTION MANUAL INSTALLING THE RECEIVER AND BATTERY 1. Plug the servo leads and the switch lead into the receiver. You may want fo plug an aileron extension into the receiver to make plugging in the aileron servo lead easier when you are installing the wing. Plug the battery pack lead into the switch. 2. Wrap the receiver and battery pack in the protective foam to protect them from vibration. Use a rubber band or masking tape to hold the foam in place.
INSTRUCTION MANUAL ~~ < Check the motor rotation > BALANCING LATERAL BALANCE 1. Its critical that your airplane be balanced correctly. After you have balanced a plane on the C.G. Improper balance will cause your plane to lose You should laterally balance it. Doing this will control and crash. help the airplane track straighter. THE CENTER OF GRAVITY IS LOCATED 1. Tum the airplane upside down.
INSTRUCTION MANUAL vy CG A Pay close attention here EH Apply Instant glue (CA glue, super glue). 160-165 mm in) 6mm Plastic Screw mom 2 12 x 210mm Aluminum 1.5 x 1200mm Plate of plywood Cut off excess.
INSTRUCTION MANUAL 3 » In order to obtain the CG specified, reposition the receiver and other equipment. » If not obtain the CG specified, add a weight and adjust. IN... » Do not fly before confirming the comet location of the CG. If the CG is income ct, you lose control of your airplane which leads to accidents. <2) CONTROL THROWS 1. We highly recommend setting up a plane using the control throws listed. 2. The control throws should be measured at the widest point of each control surface. 3.
INSTRUCTION MANUAL 12mm Xx -— ria | 12mm CN Aileron Control ~~ 5 Sell 11mm 7 . | Mmm \. Elevator Control rps sm TORN | 35mm Rudder Control 7 FOR YOUR RADIO INSTALLATION BASIC CONNECTION FOR AIRPLANE AND ADJUSTMENT OF SERVOS Example of connection @ For more information, refer to radio system instruction manual.
INSTRUCTION MANUAL DECORATION < Bottom view > < Side view > Right COVERAGE cr 3 EEN #011 Grey #023 Ferrari Red #030 Cub Yellow #071 Black £010 White 40
