SLICK 580 rE rae RT THE CONCERNING dies Gravity CG: 130 mm (5.1in) Back from the leading edge of the wing, at the fuselage Control throw Ailerons: Low: 12mm up/down; SPECIFICATION High: 15mm up/down Wingspan: 1700mm (67 in) Control throw Elevators: Low: 12mm up/down; Length: 1552mm (61.
INSTRUCTION MANUAL TABLE OF CONTENTS Introduction 1 MILITANTLY Irene 2 Disclaimer... Safety precaution Important building 2 2 Flight 2 Flight 3 Covering tools... 3 Adhesives and required tools 3 Academy of model aeronautics national Model aircraft safety code. Reinforce the fire wall and 5 Preparations 6 Installing the ailerons 6 Installing the ailerons servos 7 Installing the aileron linkages 8 Installing the main landing gear 10 Secure the wing to the 12 Installing the wing side force ..
INSTRUCTION MANUAL WARRANTY Phoenix Model guarantees the component parts in this kit to be free from defects in both material and workmanship at the date of purchase by the purchaser. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product. This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than Phoenix Model.
INSTRUCTION MANUAL FLIGHT WARNINGS * When ready to fly, first extend the transmitter aerial. * Switch on the transmitter. + Switch on the receiver. » Check that the wings are correctly fitted to the fuselage. * Operate the control sticks on the transmitter and check that the control surfaces move freely and in the CORRECT directions. * Check that the transmitter batteries have adequate power. * ALWAYS take off into the wind.
INSTRUCTION MANUAL « Officially designated AMA Air Show Teams (AST) are authorized to use devices and practices as defined within the Team AMA Program Document. (AMA Document #718.) {i} Not operate a turbine-powered aircraft, unless in compliance with the AMA turbine regulations. (AMA Document #510-A) 3.
INSTRUCTION MANUAL REINFORCE THE FIRE WALL AND PAINTING 6 200mm Triangular wood IMPORTANT NOTES 2 A Reinforcement of the fire wall using epoxy glue to paste the triangular wood (supple with the kit) to the desired positions in the drawing. Triangular wood Ao prevent gasoline from seeping into the wood, the modeler have to paint the paint on the surface of the wood as shown in the drawing. Paintbrush \.
INSTRUCTION MANUAL PREPARATIONS Use a covering iron with a covering sock on high heat to tighten the covering if necessary. Apply pressure over sheered areas to thoroughly bond the covering to the wood.
INSTRUCTION MANUAL INSTALLING THE AILERONS SERVOS 1. Install the rubber grommets and brass eyelets onto 4. Using the thread as a guide and using masking the aileron servo. tape, tape the servo lead to the end of the thread: carefully pull the thread out. When you 2. Using a modeling knife, remove the covering from over have pulled ho Parvenu lead out, remove oy the servo box. masking tape and the servo lead from the 3. Place the servo into the servo box. Center the servo thread.
INSTRUCTION MANUAL INSTALLING THE AILERON LINKAGES 4. Center the aileron and hold it in place using a } couple of pieces of masking tape. Adjust the 1. Install the control hom into the aileron. linkage until the aileron and the servo arm are both centered and then tighten the nut against. Remember use thread locking compound to secure. 2. Locate the metal rod wire, screw the plastic link ball onto the threaded end of the wire. 3. Plug the aileron serve into the receiver and center the servo.
INSTRUCTION MANUAL ZL Aileron Rod = Set all screws securely.
INSTRUCTION MANUAL INSTALLING THE MAIN LANDING GEAR < Man Gear Man Gear (L) > Front view Nylon Nut Me Collar Collar 4.2mm Collar Man gear Assemble left and right i sides the same way Apply thread locker (screw cement). FA Apply Instant glue {CA glue, super glue).
INSTRUCTION MANUAL Assemble left and right 14] rig \_ sides the same way SECURE THE WING TO THE FUSELAGE Attach the wings to the fuselage and secure the wing panels.
INSTALLING THE WING SIDE FORCE 4mm Plastic Screw Assemble left and right sides the same way Cut off shaded portion HORIZONTAL STABILIZER INSTALLATION 1. Using a modeling knife, cut away the covering from the fuselage for the stabilizer and remove it. 2. Remove the covering from the stabilizer. When cutting through the covering to remove it, cut with only enough pressure to only cut through the covering it's self. Cutting into the balsa structure may weaken it.
INSTRUCTION MANUAL RUDDER INSTALLATION =] Pay close attention here Cut off shaded portion il Apply epoxy glue INSTALLING THE RUDDER SERVO (> 1. Remove the covering from left size of the & a eee 1 fuselage. 3mm Nylon Nut 2. Install servo to the fuselage as shown. Repeat these step as installing the aileron
INSTRUCTION MANUAL Must be purchased _— Assemble left and right LA sides the same way INSTALLING THE RUDDER LINKAGES . Repeat these step as installing the aileron linkages.
INSTRUCTION MANUAL INSTALLING THE ELEVATOR SERVO 3x 12mm Screw OTD 2 1. Remove the covering from both size of the 3mm Nylon Nut fuselage. Install two servo to the fuselage as shown. Aluminum ball 3. Repeat these step as installing the aileron 3 x 20mm Cap Screw © Orrrermeree 2 control hom. (mmm 3x115mm Push rod 3mm Washer Apply threadlike (screw cement).
INSTRUCTION MANUAL 4 Assemble left and right 3 Pay close attention here Al sides the same way Must be purchased separately! Cut off shaded portion 19
INSTRUCTION MANUAL INSTALLING THE ELEVATOR LINKAGES . Repeat these step as installing the aileron linkages.
INSTRUCTION MANUAL INSTALLING THE TAIL WHEEL #2 Tail whee! set 4x 15mm Cap Screw 0 ee Cut off shaded portion
INSTRUCTION MANUAL INSTALLING THE ENGINE May be you also need to trim some wood from the tree-angle wood for the installation Using plate of plywood (supplied with the kit) mark the holes onto the fire wall for installing the engine mount for OS 1.20 or DLE 20CC. 051.
INSTRUCTION MANUAL 4 x 30mm Screw #1 (mmm 4 4mm Washer 4mm Mount Nut = Apply Instant glue {CA glue, super glue). Note the direction. m Assemble left and right 3 sides the same way fll Drill holes with the specified diameter.
INSTRUCTION MANUAL INSTALLING THE STOPPER Do not overheat, it may break.
INSTRUCTION MANUAL INSTALLING THE FUEL TANK 1. Using a modeling knife, cut one length of silicon fuel line {the length of silicon fuel line is calculated by how the weighted clunk should rest about 5mm away from the rear of the tank and move freely inside the tank). Connect one end of the line to the weighted clunk and the other end to the nylon pick up tube in the stopper. 2. Carefully bend the second nylon tube up ata 45 degree angle (using a cigarette lighter).
INSTRUCTION MANUAL INSTALLING THE THROTTLE PUSH ROD SERVO 3. Apply epoxy glue fo the push rod housing where it exits the firewall and where it passes through the 1. Place the engine into the engine mount and align it forward bulkhead. This will secure the housing in properly with the front of the cowling. place. If your engine is equipped with a remote needle 4. Using a modeling knife, cut off the nylon push rod valve, we suggest installing it into the engine at housing 26mm in front of the servo tray.
INSTRUCTION MANUAL INSTALLING THE ENGINE 1.2x600mm Throttle rod 4x30mm Screw Locate the long piece of wire used for the throttle push rod. One end of the wire has been per-bend 350mm PP Pipe bend at the factory. This "Z" bend should be inserted into the throttle arm of the engine when the engine is fitted onto the engine a mount. Fit the engine to the engine mount using 8 the screws provided.
INSTRUCTION MANUAL INSTALLING THE THROTTLE 1. Install one adjustable metal connector through the third hole out from the center of one servo arm, enlarge the hole in the servo arm using a 2mm drill bit to accommodate the servo connector. Remove the excess material from the am. After installing the adjustable metal connector apply a small drop of thin C/A to the bottom nut. This will prevent the connector from loosening during flight. 2. Plug the throttle serve into the receiver and tum on the radio system.
INSTRUCTION MANUAL < Throttle Idling > ¥ Throttle position of Tx. < Throttle Hi > < Throttle Stop > MOUNTING THE COWL 1. Remove the muffler and needle valve assembly from the engine. Slide the fiberglass cow! over the engine. 2. Measure and mark the locations to be cut out for engine head clearance, needle valve, muffler. Remove the cowl and make these cutouts using a rotary tool with a cutting disc and a rotary sanding drum attachment. 3. Slide the cowl back into place.
INSTRUCTION MANUAL Apply instant glue (CA glue, super glue). Assemble left and right sides the same way. [Al Drill holes with the specified diameter. INSTALLING THE SPINNER Install the spinner back-plate, propeller and spinner cone. The propeller should not touch any part of the spinner cone. If it dose, use a sharp modeling knife and carefully trim away the spinner cone where the propeller comes in contact with it.
INSTRUCTION MANUAL INSTALLING THE RECEIVER AND BATTERY 1. Plug the servo leads and the switch lead into the receiver. You may want to plug an aileron extension into the receiver to make plugging in the aileron servo lead easier when you are installing the wing. Plug the battery pack lead into the switch. 2. Wrap the receiver and battery pack in the protective foam to protect them from vibration. Use a rubber band or masking tape to hold the foam in place.
INSTRUCTION MANUAL 4mm Mount Nut Must be purchased separately! H Apply threadlike (screw cement). Electric Speed Controller \ Py Must be purchased \ 7) separately! 36
INSTRUCTION MANUAL ‘When rotating clock wise, change the connection of < Check the motor rotation > Must be purchased separately!
INSTRUCTION MANUAL BALANCING LATERAL BALANCE 1. It is critical that your airplanes be balanced correctly. After you have balanced a plane on the C.G. Improper balance will cause your plane to lose You should laterally balance i. Doing this will control and crash. help the airplane track straighter. THE CENTER OF GRAVITY IS LOCATED 130mm 1. Tum the airplane upside down. Attach one loop {5.1 in) BACK FROM THE LEADING EDGE OF of heavy string to the engine crankshaft and THE WING, AT THE FUSELAGE.
INSTRUCTION MANUAL 6mm Plastic Screw 210mm Aluminum y CG 130mm 1.5 x 1200mm =] Pay close attention here EH Apply instant glue (CA slug, super glue). Cut off excess.
INSTRUCTION MANUAL = » In order to obtain the CG specified, reposition A the receiver and other equipment. AN » If not obtain the CG specified, add a weight and adjust. » Do not fiy before confirming the correct location of the CG.
INSTRUCTION MANUAL CONTROL THROWS 1. We highly recommend setting up a plane using the control throws listed. _ 112mm 2. The control throws should be measured at the — 112mm widest point of each control surface. 3. Check to be sure the control surfaces move in the correct directions.
