. \ «+ SLICK 580 SIZE 60CC GP/EP ARF Control throw Ailerons: Low: 15mm up/down; SPECIFICATION High: 25mm up/down, ~ Wingspan: 2200mm (86.5 in) Control throw Elevators: Low: 15mm up/down; Length: 2172mm (85.
INSTRUCTION MANUAL pr rf Sie] Introduction 1 MILITANTLY pence 2 Disclaimer... Safety precaution 2 Important building 2 Suggestion... 2 Flight 2 Flight 3 Covering tools... 3 Adhesives and required tools 3 Academy of model aeronautics national Model aircraft safety code.
INSTRUCTION MANUAL WARRANTY Phoenix Model guarantees the component parts in this kit to be free from defects in both material and workmanship at the date of purchase by the purchaser. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product. This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than Phoenix Model.
INSTRUCTION MANUAL When ready to fly, first extend the transmitter aerial. * Switch on the transmitter. + Switch on the receiver. * Check that the wings are correctly fitted to the fuselage. * Operate the control sticks on the transmitter and check that the control surfaces move freely and in the CORRECT directions. * Check that the transmitter batteries have adequate power. * ALWAYS take off into the wind.
INSTRUCTION MANUAL « Officially designated AMA Air Show Teams (AST) are authorized to uss devices and practices as defined within the Team AMA Program Document. (AMA Document #718.) {i} Not operate a turbine-powered aircraft, unless in compliance with the AMA turbine regulations. (AMA Document #510-A) 3.
REINFORCE THE FIRE WALL AND PAINTING 6 x 200mm Triangular wood INSTRUCTION MANUAL —— IMPORTANT NOTES 2 CA A Reinforcement of the fire wall using epoxy glue to paste the triangular wood (supped with the kit) to the desired positions in the drawing. = Triangular wood AlB Triangular wood 0 . Triangular wood Triangular wood Triangular wood ATo prevent gasoline from seeping into the wood, the modeler have to paint the paint on the surface of the wood as shown in the drawing.
INSTRUCTION MANUAL PREPARATIONS Use a covering iron with a covering sock on high heat to tighten the covering if necessary. Apply pressure over sheered areas to thoroughly bond the covering to the wood. A) mn Assemble left and right Y sides the same way INSTALLING THE AILERONS { \ < Bottom view > Main Wing » Make certain the hinges are adequately secured with glue. If they come loose in flight accidents may result.
INSTRUCTION MANUAL INSTALLING THE AILERONS SERVOS 1. Install the rubber grommets and brass eyelets onto 4. Using the thread as a guide and using masking the aileron servo. tape, tape the servo lead to the end of the 2. Using a modeling knife, remove the covering from over thread: carefully pull the dread out. When you have pulled the servo lead out, remove the masking tape and the servo lead from the 3. Place the servo into the servo box. Center the servo thread.
INSTRUCTION MANUAL INSTALLING THE AILERON LINKAGES 4. Center the aileron and hold it in place using a © " couple of pieces of masking tape. Adjust the 1. Install the control hom into the aileron. linkage until the aileron and the servo am are both centered and then tighten the nut against. Remember use thread locking compound to secure. 2. Locate the metal rod wire, screw the plastic link ball onto the threaded end of the wire. 3. Plug the aileron serve into the receiver and center the servo.
INSTRUCTION MANUAL 3x12mm = Set all screws securely.
INSTRUCTION MANUAL INSTALLING THE MAIN LANDING GEAR Cut off shaded portion 4 Assemble left and right "41 sides the same way < Main Gear (R) > < Left > < Main Gear (L) >
INSTRUCTION MANUAL Washer Man gear Wheel pant Collar Washer Whee! 2A 8mm Cut off shaded portion =) Apply thread locker {screw cement).
INSTRUCTION MANUAL SECURE THE WING TO THE FUSELAGE 6mm Plastic Screw Attach the wings to the fuselage and secure the oI 4 wing panels. 6mm Cut off shaded portion LA] Assemble left and right "43 sides the same way £4 INSTALLING THE WING SIDE FORCE 4mm Plastic Screw orm 4 Assemble left and right Ex .
INSTRUCTION MANUAL HORIZONTAL STABILIZER INSTALLATION 1. Using a modeling knife, cut away the covering from the fuss lags for the stabilizer and remove it. 2. Remove the covering from the stabilizer. When cutting through the covering to remove it, cut with only enough pressure to only cut through the covering it's self. Cutting into the balsa structure may weaken it. This could lead to possible failure during flight. 3. Attach the wing to the fuselage as picture. 4.
INSTRUCTION MANUAL Cut off shaded portion Assemble left and right ides the same way 2s
INSTRUCTION MANUAL Cut off shaded portion Must be purchased 16 separately! LA] Assemble left and right "4% sides the same way
INSTRUCTION MANUAL N = Cut off shaded portion > Make certain plane Is aligned 4 Assemble left and right AN n accurately per the diagram. sides the same way. bch] : A sim-aligned plane can fly a Pay close attention here erratically and cause accidents.
INSTRUCTION MANUAL RUDDER INSTALLATION Cut off shaded portion oY) Apply epoxy glue INSTALLING THE RUDDER LINKAGES 9. Attach the clevis to the rudder servo. There should be The rudder is controlled by two metal cables. Install po anion on each of the wires when installed the rudder linkages and cables as below. y. ] 1. Use a hobby knife to remove the covering from Note: Remember use thread locking compound to the openings for the rudder control cables. 3x 12mm Screw 2.
INSTRUCTION MANUAL Aluminum ball O i 3x12mm SHE) C00 Cut off shaded portion Must be purchased separately! [A Pay close attention here
INSTRUCTION MANUAL INSTALLING THE TAIL WHEEL #2-Tail wheel set 4x 15mm Cap Screw Se (] I Cut off shaded portion
INSTRUCTION MANUAL INSTALLING THE ENGINE Using plate of plywood {supplied with the kit) mark the holes onto the fire wall for installing the engine mount for DLE-61CC or OS-GTE. © DLE6ICC o Qo Throttle Lever OR May be you also need to trim ‘some wood from the tree-angle wood for the installation is easy.
INSTRUCTION MANUAL { Apply instant glue (CA glue, super glue). Note the direction. Apply threadlike Assemble left and right Ji{ Must be purchased EES Drill holes with the (screw cement). LA sides the same way X separately! 1.5m) specified diameter. Metal wiki link (M2) May be you also need to trim some G wood from the tree-angle wood for 2mm Silicons 237 2 SE 2 the installation is easy.
INSTRUCTION MANUAL INSTALLING THE STOPPER it may break.
INSTRUCTION MANUAL INSTALLING THE FUEL TANK 1. Using a modeling knife, cut one length of silicon fuel line (the length of silicon fuel line is calculated by how the weighted clunk should rest about 5mm away from the rear of the tank and move freely inside the tank). Connect one end of the line to the weighted clunk and the other end to the nylon pick up tube in the stopper. 2. Carefully bend the second nylon tube degree angle {using a cigarette lighter). This tubs will be the vent tube to the muffler. 3.
INSTRUCTION MANUAL 3 x 10mm TP Screw (oe 2 Apply instant glue 21 (CA glue, super glue). INSTALLING THE THROTTLE 1. Plug the throttle servo into the receiver and tum on the radio system. Check to ensure that the throttle servo output shaft is moving in the correct direction. When the throttle stick is moved forward from idle to full throttle, the throttle barrel should also open and close using this motion. If not, reverse the direction of the servo, using the transmitter.
INSTRUCTION MANUAL MOUNTING THE COWL 4. While holding the cow! firmly in position, drill four 1,6mm pilot holes through both the cowl 1. Remove the muffler and needle valve assembly and the side edges of the firewall. from the engine. Slide the fiberglass cowl over the | . engine. 5. Using a 3mm drill bit, enlarge the four holes in the cowling. 2. Measure and mark the locations to be cut out for A engine head clearance, needle valve, muffler.
INSTRUCTION MANUAL LA Assemble left and right "4 sides the same way. Drill holes with the specified diameter. INSTALLING THE SPINNER AN Install the spinner back-plate, propeller and spinner cone. = Securely tighten the nut holding the propeller for it not come off when the motor Is spinning. If coming off, theta Is a high risk of The propeller should not touch any part of the Injury! spinner cone. If it dose, use a sharp modeling > Ways ensure propeller and spinner are balanced.
INSTRUCTION MANUAL INSTALLING THE RECEIVER AND BATTERY INSTALLING THE SWITCH 1. Plug the servo leads and the switch lead into the 1. The switch should be mounted on the fuselage receiver. You may want to plug an aileron side, opposite the muffler, close enough to the extension into the receiver to make plugging in the receiver so the lead will reach. Use the face plate aileron servo lead easier when you are installing of the switch cut out and locate the mounting the wing.
INSTRUCTION MANUAL Velcro EC” Cord Top Hatch < Check the motor rotation > Electric Speed Controller Must be purchased separately! Open and Close J) When rotating clock wise, change the connection of 2 wires.
INSTRUCTION MANUAL BALANCING LATERAL BALANCE 1. Iris critical that your airplane be balanced correctly. After you have balanced a plane on the C.G. Improper balance will cause your plane to lose You should laterally balance it. Doing this will control and crash. help the airplane track straighter. THE CENTER OF GRAVITY IS LOCATED 165mm 1. Tum the airplane upside down. Attach one loop 6s In) ACK FROM FUE LEADING EDUCE OF of heavy string to the engine crankshaft and one to the tail wheel wire.
INSTRUCTION MANUAL A » Do not fly before confirming the correct location of the CG. If the CG is income ct, you lose control 3 » In order to obtain the CG specified, reposition the receiver and other equipment » If not obtain the CG specified, add a weight and a Pay close attention here Apply Instant glue £1 (CA glue, super glue). Cut off excess.
INSTRUCTION MANUAL Open and Close CONTROL THROWS 1. We highly recommend setting up a plane using the control throws listed. 2. The control throws should be measured at the widest point of each control surface. 3. Check to be sure the control surfaces move in the correct directions. 2 Sos 2 ] 15mm 15mm Aileron Control Deg 1 16mm Cote AN | 15mm Elevator Control > oo.
INSTRUCTION MANUAL «CHANNEL RADIO SETUP FLIGHT PREPARATION PRE FLIGHT CHECK {STANDARD MODE 2) PE 1. Completely charge your transmitter and receiver batteries before your first day of flying. | — 2. Check every bolt and every glue joint in your a RIGHT. a plane to ensure that everything is tight and well LEFT AILERON MOSEY DOWN bonded. a5 os 3. Double check the balance of the airplane 4. Check the control surface RUDDER MOVES RIGHT ~~ CARBURETOR WIDE OPEN 5. Check the receiver antenna .
