: he +> LOCKE WOLF FWIW os had ot Cdl bei pd rile SPECIFICATION Wingspan: 1720mm (68 in) Length: 1480mm (59 in) Control throw Elevators: Low: 14mm up/down; High: 17mm up/down Control throw Rudder: Low: 20mm right/left; Flying weight: 5200-5400g High: 30mm rightful Wing area: 51.
INSTRUCTION MANUAL TABLE OF CONTENTS Introduction 1 Installing the engine mount 23 WAIT ANY evens ease teens ese amanuenses seas 2 Installing the 24 Disclaimer... Installing the fuel tank end 25 Safety precaution Installing the throttle push rod 26 Important building 2 Installing the Ines 27 SUGGESTION. ...evince vine errand 2 Installing the throttle 30 Flight 2 Mounting the cowl 31 Flight 3 Installing the spinner 33 Covering tools...
INSTRUCTION MANUAL WARRANTY Phoenix Model guarantees the component parts in this kit to be free from defects in both material and workmanship at the date of purchase by the purchaser. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product. This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than Phoenix Model.
INSTRUCTION MANUAL FLIGHT WARNINGS * When ready to fly, first extend the transmitter aerial. * Switch on the transmitter. + Switch on the receiver. » Check that the wings are correctly fitted to the fuselage. * Operate the control sticks on the transmitter and check that the control surfaces move freely and in the CORRECT directions. * Check that the transmitter batteries have adequate power. * ALWAYS take off into the wind.
INSTRUCTION MANUAL « Officially designated AMA Air Show Teams (AST) are authorized to use devices and practices as defined within the Team AMA Program Document. (AMA Document #718.) {i} Not operate a turbine-powered aircraft, unless in compliance with the AMA turbine regulations. (AMA Document #510-A) 3.
INSTRUCTION MANUAL REINFORCE THE FIRE WALL AND PAINTING 6 200mm Triangular wood IMPORTANT NOTES 2 A Reinforcement of the fire wall using epoxy glue to paste the triangular wood (supple with the kit) to the desired positions in the drawing. B Triangular wood 2A Triangular wood AlB AlB Triangular wood Ao prevent gasoline from seeping into the wood, the modeler have to paint the paint on the surface of the wood as shown in the drawing. Paintbrush \.
INSTRUCTION MANUAL PREPARATIONS Use a covering iron with a covering sock on ZA high heat to tighten the covering if necessary. Apply pressure over sheered areas to thoroughly bond the covering to the wood. LA Assemble left and right "43 sides the same way INSTALLING THE AILERONS AND FLAPS /N WARNINGS < RIGHT > 4 Assemble left and right "4 sides the same way Cut off shaded portion pa Drill holes with the specified diameter. Apply instant glue 6 {CA slug, super glue). P-Plazas note that C.
INSTRUCTION MANUAL eo Aluminum ball J 70mm Push rod 9 3x15mm < < Flap > Flap Hom Flap 3x10mm Flap = > Flap Main Wing 2 < Bottom view > > Please note that C A glue must be apply to these holes before screw the control hom to the aileron. If nat, it comes off during flights, you may lose control of your airplane, resulting in an accident | N Ensure smooth, non-binding movement when assembling fl Apply epoxy glue Apply instant glue {CA slug, super gust.
INSTRUCTION MANUAL INSTALLING THE AILERONS AND FLAPS 1. Install the rubber grommets and brass eyelets onto the aileron servo. 2. Using a modeling knife, remove the covering from over the per-cut servo arm exit hole on the aileron servo tray / hatch. This hole will allow the servo arm to pass through when installing the aileron push rods. 3. Place the servo into the servo tray.
INSTRUCTION MANUAL INSTALLING THE AILERONS AND FLAPS LINKAGES Control hor Metal wiki link (M3) AP Silicons Qo 2 60 ball co 3x 10mm TP Screw Control horn caballero 10mm Button Screw (mm eee 2 Metal wiki link (M3) a 2 Silicone Q 2 Aluminum ball 00cr 3x 10mm TP Screw Go % wi link Aluminum pal E, J) 65mm Push red 3x10mm Assemble left and right = sides the same way
INSTRUCTION MANUAL INSTALLING THE PLASTIC COVER Plastic cover Plastic cover Ll Set all screws securely.
INSTRUCTION MANUAL INSTALLING THE MAIN LANDING GEAR 5 x 40mm Cap Screw or ou < Main Gear (L) > < Main Gear (R} > H Apply thread locker (screw cement).
Wiki link (M3) Retract Rod Silicon tube Wiki link (M3) Silicon tube &] Pay close attention here PY Apply epoxy glue Drill holes with the tim specified diameter.
£3 Cutaway film only. here = Cut off shaded portion P81 Apply epoxy gue SECURE THE WING TO THE FUSELAGE Attach the wings to the fuselage and secure the wing panels. 6mm Plastic Screw — £3 Cut away film only.
HORIZONTAL STABILIZER INSTALLATION 1. Using a modeling knife, cut away the covering from the fuselage for the stabilizer and removes it. 2. Draw a center line onto the horizontal stabilizer. 3. Check the fit of the horizontal stabilizer in its slot. Make sure the horizontal stabilizer is square and centered to the fuselage by taking measurements, but don't glue anything yet. 4.
A=A B=P INSTALLING THE RUDDER AND TAIL GEAR Sra Soe 3x12mm TP © Secure nylon hinges with instant glue, being careful tail wing and elevator. © Align the center line of vertical fin with rudder. I] Apply epoxy glue Ensure smooth, non-binding movement when assembling = > Take off the main wing after put a rudder.
INSTALLING THE RUDDER PUSH ROD 1. Locate the push rod exit slot on the right side of the fuselage. 2. Carefully cut away the covering material from the slot. 3. Working from inside the fuselage, slide the threaded end of the remaining push rod down the inside of the fuselage until the push rod reaches the exit slot. Carefully reach in with a small screw driver and guide the push rod out of the exit slot. 4. Install the nylon clevis on the rudder push rod. Make sure 6mm of thread shows inside the clevis. 5.
INSTRUCTION MANUAL A Set all screws securely. If they come off during flight you will lose control of your aircraft! Rudder Servo Rudder Rod C= Cut off excess. Cut off shaded portion aE Pay close attention here Must be purchased separately! INSTALLING THE ELEVATOR PUSH ROD 1. Locate the push rod exit slot on the right side and left side of the fuselage. It is located slightly ahead and below the horizontal stabilizer. 2. Carefully cut away the covering material from the slot. 3.
Elevator Servo Rudder Servo | J Elevator Rod | N | Domino Hols ant ome | © émm Neutral hy = Assemble left and right £3 Marquis put [3 Pay close attention here sides the same way [% Must be purchased Cut off shaded portion Cut off excess separately! ’ 2
INSTALLING THE ENGINE installing the engine mount for 08 Using plate of plywood (supplied with the kit) mark the holes onto the fire wall for 1.20 or DLE 20CC. May be you also need to trim some wood from the tree-angle wood for the installation is easy. Plate of plywood .
#1 4 x 30mm Screw (Cm + 4mm Washer 4mm 4x30mm =a rs Engine Mount Apply instant glue (CA glue, super glue). Note the direction. KH Apply thread locker Ld] Assemble left and right kl Drill holes with the (screw cement). "4 sides the same way fl. Sm specified diameter.
INSTALLING THE STOPPER INSTRUCTION MANUAL WARNING Do not overheat, it may break.
INSTRUCTION MANUAL INSTALLING THE FUEL TANK 1. Using a modeling knife, cut one length of silicon fuel line {the length of silicon fuel line is calculated by how the weighted clunk should rest about 5mm away from the rear of the tank and move freely inside the tank). Connect one end of the line to the weighted clunk and the other end to the nylon pick up tube in the stopper. 2. Carefully bend the second nylon tube up ata 45 degree angle (using a cigarette lighter).
INSTRUCTION MANUAL INSTALLING THE THROTTLE PUSH ROD SERVO 1. Place the engine into the engine mount and align Apply epoxy glue to the push rod housing where it properly with the front of the cowling. exits the firewall and where it passes through the If your engine is equipped with a remote needle forward bulkhead. This will secure the housing in valve, we suggest installing it into the engine at P : this time. 4. Using a modeling knife, cut off the nylon push rod 2.
INSTRUCTION MANUAL INSTALLING THE ENGINE Locate the long piece of wire used for the throttle push rod. One end of the wire has been per-bend bend at the factory. This "2" bend should be inserted into the throttle arm of the engine when the engine is fitted onto the engine mount. Fit the engine to the engine mount using the screws provided. Must be purchased separately! 1.
INSTRUCTION MANUAL Metal wiki link (M2) Silicone 1.
DLE-20RA DLE 20cc with rear exhaust IDLE-20 DLE 20cc with side exhaust Silicone Throttle Lover Choke Lever Silicone Must be purchased separately!
INSTRUCTION MANUAL INSTALLING THE THROTTLE 1. Install one adjustable metal connector through the third hole out from the center of one servo arm, enlarge the hole in the servo arm using a 2mm drill bit to accommodate the servo connector. Remove the excess material from the am. After installing the adjustable metal connector apply a small drop of thin C/A to the bottom nut. This will prevent the connector from loosening during flight. 2. Plug the throttle serve into the receiver and tum on the radio system.
INSTRUCTION MANUAL MOUNTING THE COWL 1. Remove the muffler and needle valve assembly from the engine. Slide the fiberglass cowl over the engine. 2. Measure and mark the locations to be cut out for engine head clearance, needle valve, muffler. Remove the cowl and make these cutouts using a rotary tool with a cutting disc and a rotary sanding drum attachment. 3. Slide the cowl back into place. Align the front of the cowl with the crankshaft of the engine.
INSTRUCTION MANUAL Plate of plywood £3 Trim the cowling so it will match your engine 4 Assemble left and right J sides the same way. Cut off shaded portion 2 Apply Instant glue [1 (CA glue, super glucose. Dil hot hth H rill holes with the [ATS RY] Apply epoxy glue [2mm] specified diameter.
INSTALLING THE SPINNER Install the spinner back-plate, propeller and spinner cone. The propeller should not touch any part of the spinner cone. if it dose, use a sharp modeling knife and carefully trim away the spinner cone where the propeller comes in contact with il. 3x12mm TP Screw (ome Emma Spinner Propeller > Use the spacer suitable for shatter. = Securely tighten the nut holding the propeller for it not come off when the motor is spinning.
INSTRUCTION MANUAL Slide Louvers Epoxy or silicone glue INSTALLING THE RECEIVER AND BATTERY INSTALLING THE SWITCH 1. Plug the servo leads and the switch lead into the 1. The switch should be mounted on the fuselage receiver. You may want to plug an aileron side, opposite the muffler, close enough to the extension into the receiver to make plugging in the receiver so the lead will reach.
INSTRUCTION MANUAL INSTALLING THE ELECTRIC MOTOR ( EP VERSION ) 4 x 70mm Cap Screw 5mm Washer —m (© A White glue 4mm Mount Nut 4x70mm 4x70mm Must be purchased separately! Apply thread locker {screw cement).
INSTRUCTION MANUAL Electric Spade oT When rotating clock wise, change the connection of 2 wires.
INSTRUCTION MANUAL INSTALLING THE GUN COVER = Cut off shaded portion 2] Apply instant glue {CA glue, super glue).
INSTRUCTION MANUAL 1. It is critical that your airplane be balanced correctly. Improper balance will cause your plane to lose control and crash. THE CENTER OF GRAVITY IS LOCATED 125mm ( 4.9 in) BACK FROM THE LEADING EDGE OF THE WING, AT THE FUSELAGE. BALANCE A PLANE UPSIDE DOWN WITH THE FUEL TANK EMPTY. . Mount the wing to the fuselage. Using a couple of pieces of masking tape, place them on the top side of the wing 125mm ( 4.9 in) back from the leading edge, at the fuselage sides. 3.
INSTRUCTION MANUAL FLIGHT PREPARATION PRE FLIGHT CHECK 1. Completely charge your transmitter and receiver batteries before your first day of flying. Check every bolt and every glue joint in your plane to ensure that everything is tight and well bonded. Double check the balance of the airplane. Check the control surface. Check the receiver antenna. It should be fully extended and not coiled up inside the fuselage. Properly balance the propeller.
INSTRUCTION MANUAL DECORATION P= Place the decals as shown below. P Align the decals with mark of fuselage.
