User manual

ManualsBrandsPhoenix ManualsNetworkingGigabit Smart Managed CompSwitch 8x TP -

7470_en_00

AUTOMATIONWORX

FL SWITCH SMCS 8GT

Data Sheet

Description

Smart Managed Compact Switch (SMCS)

The managed compact switch with one Gigabit on all eight

ports enables the cost-effective creation of managed Ether-

net networks in industrial environments with maximum

throughput rates. The compact switches in metal housing

support the use of the optional FL MEM PLUG. The

FL MEM PLUG is a plug-in parameterization memory on

which the entire configuration of the device can be stored so

that it can be transferred to another device, if required.

Properties of the SMCS

– 10/100/1000 Mbps on all ports

– Management via SNMP (Simple Management Network

Protocol), via WBM (web-based management) or via

serial interface (HyperTerminal)

– Redundant supply voltage connection

– Floating alarm contact with adjustable function

– Labeling fields for the device and the individual ports

– Redundancy with Rapid Spanning Tree (RSTP

IEEE 801.1w) and Fast Ring Detection (compatible to

FL SWITCH MM HS and FL SWITCH MCS with Fast

Ethernet)

– Local diagnostic and status indicators

– Optional FL MEM PLUG supported as a changeable

parameterization memory

– LLDP support (IEEE 802.1ab)

- Improved error location detection

- Improved device replacement

- More efficient network configuration

Fields of Application

Typical fields of application for the SMCS range from high-

performance connection to Gigabit office networks through

the function of a powerful distributor in control cabinets to

typical use in Industrial Ethernet applications. A special fea-

ture is the support of PROFINET and Ethernet/IP.

For additional information about the function and operation of the SMCS, please refer to the

"UM EN FL SWITCH SMCS" product-specific user manual. It can be downloaded at

www.download.phoenixcontact.com

Make sure you always use the latest documentation.

It can be downloaded at www.download.phoenixcontact.com

A conversion table is available on the Internet at

www.download.phoenixcontact.com/general/7000_en_00.pdf.

This data sheet is valid for all products listed on the following page:

Smart Managed Compact Switch

With Eight Gigabit Ports

Summary of content (10 pages)

PAGE 1
FL SWITCH SMCS 8GT Smart Managed Compact Switch With Eight Gigabit Ports AUTOMATIONWORX Data Sheet 7470_en_00 © PHOENIX CONTACT - 11/2006 Description – Smart Managed Compact Switch (SMCS) The managed compact switch with one Gigabit on all eight ports enables the cost-effective creation of managed Ethernet networks in industrial environments with maximum throughput rates. The compact switches in metal housing support the use of the optional FL MEM PLUG.
PAGE 2
FL SWITCH SMCS 8GT Ordering Data Products Description Type Order No. Pcs./Pck. Smart managed compact switch with eight Gigabit ports in RJ45 format Product Short Description 2891123 1 Plug-in parameterization memory FL MEM PLUG 2891259 1 Accessories Description Type Order No. Pcs./Pck. Configuration cable for connecting the switch with a PC, V.
PAGE 3
FL SWITCH SMCS 8GT Technical Data General Data Function Smart managed compact switch, Ethernet/Fast Ethernet/Gigabit switch; conforms to standard IEEE 802.3/802.3u/802.
PAGE 4
FL SWITCH SMCS 8GT Mechanical Tests Shock test according to IEC 60068-2-27 Operation: 25g half-sine shock pulse Storage/transport: 50g, half-sine shock pulse Vibration resistance according to IEC 60068-2-6 Operation/storage/transport: 5g, 10 - 150 Hz Free fall according to IEC 60068-2-32 1m Conformance With EMC Directives Developed in acc. with IEC 61000-6.2 Emitted interference acc.
PAGE 5
FL SWITCH SMCS 8GT Installation and Assembly/Removal Install the smart managed compact switch on a clean DIN rail according to EN 60715. To avoid contact resistance only use clean, corrosion-free DIN rails. End clamps can be mounted on both sides of the module to stop the modules from slipping on the DIN rail. Assembly 1. 2. 3. Place the module onto the DIN rail from above. The upper holding keyway must be hooked onto the top edge of the DIN rail.
PAGE 6
FL SWITCH SMCS 8GT Alarm Contact The switch has a floating alarm contact. An error is indicated when the contact is opened. R 1 R 2 6 7 8 4 0 0 1 5 Figure 2 Circuit diagram for the alarm contact The indicated error states are configured in web-based management or via SNMP. V.24 (RS-232) Interface for External Management The 6-pos. Mini-DIN female connector provides a serial interface to connect a local management station.
PAGE 7
FL SWITCH SMCS 8GT Assignment of the RJ45 Ethernet Connectors Please note that for operation with 1000 Mbps (Gigabit), cables with four twisted pairs (eight wires), which meet the requirements of Cat 5 as a minimum, must be used.
PAGE 8
FL SWITCH SMCS 8GT Status and Diagnostic Indicators Des. Color US1 Green US2 Green FAIL Red Status Meaning ON Supply voltage 1 in the tolerance range OFF Supply voltage 1 too low ON Supply voltage 2 in the tolerance range OFF Supply voltage 2 too low ON Alarm contact open, i.e., an error has occurred OFF Alarm contact closed, i.e.
PAGE 9
FL SWITCH SMCS 8GT Diagnostics via the Alarm Contact If either or both of the supply voltages fails, the alarm contact opens. On a restart, the switch executes a hardware selftest. In the event of an error during the selftest, an SNMP trap is transmitted. Status and Diagnostic Indicators These indicators provide information about the status of the SMCS at all times. Local diagnostics without additional tools is possible thanks to numerous LEDs.
PAGE 10
FL SWITCH SMCS 8GT Housing Dimensions Depth 69 mm from upper edge of DIN rail 128 mm / 5.04 in. 69 mm / 2.72 in. MODE FL SWITCH SMSC 8GT Ord. No. 2891123 ACT SPD FD 1 3 5 7 2 4 6 8 LINK MAC Address 100 mm / 3.94 in. US1 US2 FAIL 1 00.A0.45.06.04.02 2 3 4 5 6 7 8 Mode X10 R1 R2 X11 MEM X12 V.24 55 mm / 2.1655 in. X9 US1 GND US2 GND FL MEM PLUG 2891259 Figure 5 10 mm / 0.39 in. Housing dimensions © PHOENIX CONTACT 11/2006 7470_en_00 PHOENIX CONTACT GmbH & Co.