Phonak ComPilot User Guide
Contents 1. Welcome 5 2. Getting to know your ComPilot 6 2.1 Legend 7 2.2 Accessories 8 3. Getting started 9 3.1 Setting up the power supply 3.2 Charging the ComPilot battery 9 10 3.3 Turning the ComPilot ON and OFF 11 3.4 ComPilot Bluetooth pairing introduction 13 3.5 Wearing the ComPilot correctly 14 3.6 Testing sound via the ComPilot 15 4. Using the ComPilot as an audio streamer 16 16 4.2 Streaming music via Bluetooth 17 4.3 Watching TV 19 4.
5. Using the ComPilot for phone calls 5.1 Introduction 21 21 5.2 Incoming calls 25 5.3 Making phone calls 28 5.4 Ending a call 29 5.5 Advanced phone options 30 5.6 Using the external microphone 32 5.7 Locking the main button 33 6. Using the ComPilot as a remote control 34 7. Using the ComPilot with FM 38 8. More detailed information 40 8.1 Wearing the ComPilot in different ways 41 8.2 Managing multiple inputs to the ComPilot 42 8.3 Resetting your ComPilot 47 8.
Contents 8.6 Setting up Bluetooth 56 8.7 Caller identification: spoken caller names 62 8.8 VoiceAlerts: spoken ComPilot status 63 9. Troubleshooting ComPilot 10. Important safety information 65 73 10.1 Hazard warnings 73 10.2 Information on product safety 75 10.3 Other important information 78 79 12. Compliance information 81 13. Information and explanation of symbols 84 4 11.
1. Welcome Your new ComPilot is a Swiss premium-quality product developed by Phonak, one of the world‘s leading companies in hearing technology. Please read the user instructions thoroughly in order to benefit from all the possibilities your hearing system offers. “Compatibility information: Check your hearing aid compatibility with your hearing care professional.” Phonak – life is on www.phonak-us.
2. Getting to know your ComPilot The intended use of the Phonak ComPilot is to connect all Phonak wireless hearing aids wirelessly to Bluetooth®-enabled phones and devices or MP3 players for speech or stereo music. The ComPilot is also compatible with Phonak’s range of FM/Roger receivers via Europlug input. The remote control gives you access to important control elements for most of the Phonak wireless hearing aids. A list of compatible hearing aids can be found at http://www.phonak.
2.1 Legend Buttons a Main ( ) b Volume +/- ( c Home ( ) d Connect ( ) e ON/OFF switch ( k j l a ) b ) Inputs f Microphone openings g Audio input (3.
2. Getting to know your ComPilot 2.2 Accessories (content may vary depending on the country) o/p Universal power supply with mini-USB plug q–t US, EU, UK, AUS adapter p q r o s t Other optional accessories J External lapel microphone “MC1” J Short neckloop (51 cm) J Phonak TVLink S basestation (Phonak Bluetooth transmitter for TV use) J Audio cable, 1.5 m / 5 ft. J USB cable, 3 m / 10 ft.
3. Getting started 3.1 Setting up the power supply 1. Select the adapter that corresponds to your country. US EU UK AUS 2. Insert the round corner of the adapter to the round corner of the universal power supply until it is completely inserted. 2. 3. 3. Click the tail of the adapter in to lock it into place. Make sure the adapter is securely locked. To remove the power adapter: a. Pull back the tab on the universal power supply and hold. b.
3. Getting started 3.2 Charging the ComPilot battery Your ComPilot has a non-removable rechargeable battery. To charge it: 1. Plug the mini-USB plug into the mini-USB port on the ComPilot. 2. Plug the power supply into a power outlet. Power indicator J Solid red: Charging, typically 90 minutes. J Solid green: Battery fully charged. It is safe to leave the ComPilot connected to the charger overnight.
I A new battery’s full performance is achieved only after two to three complete charge and discharge cycles. 3.3 Turning the ComPilot ON and OFF Slide the Power switch ( ) as shown to turn the ComPilot ON or OFF. OFF ON Switch the ComPilot OFF when not in use or if in storage or during transportation. For operational use switch the ComPilot ON.
3. Getting started Battery status information The Power indicator shows the following: Green for 2 seconds Switching ON Blink red then solid for 2 seconds Switching OFF Slow blink green Normal operation Short blink red <20% battery left. Please charge No blinking just after switching ON Charge for at least 2 hours I If the neckloop was removed for more than 2 minutes, the Power indicator is only lit as long as a button is pressed.
3.4 ComPilot Bluetooth pairing introduction Find more details on page 56. 1. Switch ON ( ) the ComPilot. 2. Press and hold the Connect ( ) and Volume ( ) button simultaneously for 2 seconds until the Audio indicator starts to rapidly blink blue. 2 sec 3. Start the pairing process on the Bluetooth device (e.g., phone) within 1 minute according to the devices user guide and use code “0000” when prompted. 4. After successful pairing, the Audio indicator will stop rapidly blinking blue.
3. Getting started 3.5 Wearing the ComPilot correctly Before any phone, music or TV streaming can take place, the ComPilot must be switched ON and worn correctly as shown below: 1. Put the neckloop around your neck (easily done when unplugging one neckloop plug). 2. Make sure both plugs are well connected in the neckloop sockets. 3. Switch the ComPilot ON. I For streaming the neckloop must always be plugged in. When unplugged, the ComPilot will go into sleep mode after two minutes.
3.6 Testing sound via the ComPilot 1. Wear the ComPilot correctly and switch it ON. 2. Press and hold the Connect ( ) and Main ( ) buttons simultaneously for 2 seconds until the Audio indicator turns violet. The hearing aids will switch to the streaming mode and you will hear the ComPilot theme sound demo for 30 seconds. Use the Volume ( ) buttons to adjust the volume. The volume level is permanently stored and will be applied to all VoiceAlert messages.
4. Using the ComPilot as an audio streamer 4.1 Streaming music via a cable The ComPilot must be switched ON and worn correctly around your neck. 1. Insert the audio cable into the headphones socket on your audio player and start the player. 2. Insert the other end of the audio cable into the Audio input on your ComPilot. The audio streaming is automatically activated and the Audio indicator will change to orange.
Briefly press the Main ( streaming. ) button to stop and restart The programs of your hearing aids cannot be changed via the ComPilot Main ( ) button when the audio cable is plugged in. I ComPilot will confirm streaming via cable when activated (speech messages (VoiceAlerts) or beeps, according to the ComPilot configuration). 4.2 Streaming music via Bluetooth If you have an audio source equipped with Bluetooth functionality (e.g., MP3 player), you can stream audio wirelessly to your hearing aids.
4. Using the ComPilot as an audio streamer 3. For some Bluetooth devices it may be necessary to press “Play” on the device. 4. If the devices were paired and connected correctly streaming will start automatically and the Audio indicator will turn solid blue. Use the Main ( streaming. ) button to stop and restart Bluetooth To stop Bluetooth streaming completely, switch the other Bluetooth device OFF or disable its Bluetooth feature.
4.3 Watching TV We recommend using the dedicated and optimized Phonak TVLink S or TVLink II basestation for watching TV. They ensure low latency wireless transmission for up to 30 meters (90 ft.), offer a built-in volume control and act as a charging cradle for the ComPilot.
4. Using the ComPilot as an audio streamer 4.4 Adjusting the volume Press the ComPilot Volume ( ) buttons to adjust: J Press ( ) to increase the volume J Press ( ) to decrease the volume I Adjusting the volume on the ComPilot will have the same effect as adjusting the volume of the hearing aids. You can also change the volume of the streaming audio signal only by using the volume controls of the audio device (e.g., cellular phone, MP3 player, TVLink S basestation).
5. Using the ComPilot for phone calls 5.1 Introduction Before you can use your ComPilot with your phone, you need to make sure the phone is Bluetooth enabled and complete the pairing and connection procedures (details on page 56).
5. Using the ComPilot for phone calls The Main ( ) button offers multi-operation functionality: J It accepts and ends a phone call. J It pauses and resumes the streaming from an audio device. J It operates as a remote control (ComPilot must be configured as a remote control by your hearing care professional). Some phones are configured to play key-press tones, SMS announcements and confirmation beeps to the ComPilot.
I Phone calls via Bluetooth will always take priority over other audio sources on your ComPilot. I It is not possible to change hearing aid programs during a phone call. I You will hear the caller’s voice through both hearing aids.
5. Using the ComPilot for phone calls Use of ComPilot during phone calls The Bluetooth range (maximum distance between ComPilot and the phone) is 5–10 meters (15–30 ft). Outside this range the connection will be lost or you will encounter intermittency during a call. When engaged in a phone call, wear the ComPilot normally as shown in figure a below. J In very noisy environments, you may move the ComPilot closer to your mouth (figure b).
5.2 Incoming calls The ComPilot must be switched ON, paired to the phone and worn correctly. When a call is received on your phone, the ComPilot Audio indicator will show a solid blue light, and you will hear the ringtone signal through your hearing aids. Different ringtones of the ComPilot The phone ringtone depends on the ComPilot configuration and your phone capabilities. The ringtone is assigned automatically during the initial phone pairing process and cannot be configured.
5. Using the ComPilot for phone calls The ComPilot will also announce the caller name as shown on the phone display (Caller identification using text-to-speech technology). The name is taken from your phone’s directory. I Please note that this feature must be supported by your phone. Please consult the phone user guide or the phone supplier for more information. I The default language setting of a new ComPilot is US English.
It will take about 5 seconds before you hear the ringtone through your hearing aids. I For your safety, the hearing aid microphones will remain on at reduced level during phone calls and audio streaming. I Only one phone call at a time is possible. A second ringing phone is ignored while phoning.
5. Using the ComPilot for phone calls 5.3 Making phone calls Make sure the ComPilot and your phone are connected through Bluetooth as described on page 56. Use the phone keypad to enter the number and press the phone dialing button. When connected, you will hear the dialing tone through your hearing aid after approximately 3 seconds.
1. Type the number you want to dial on your phone, or select it from the phone book. 2. Briefly press the Connect ( ) button then wait 5 seconds. 3. The dialing process will automatically start and the Audio indicator will turn solid blue. You may hear a confirmation beep through your hearing aids. 5.4 Ending a call To end a phone call via your ComPilot, briefly press the Main ( ) button.
5. Using the ComPilot for phone calls 5.5 Advanced phone options Rejecting a call If you prefer not to answer an incoming call, press and hold the Main ( ) button on your ComPilot for about two seconds until the ringtone stops. Using your phone to reject the call will have the same effect. Pressing the Home ( ) button will terminate the call and the hearing aids will switch to the startup program. Your hearing care professional may configure the following additional features on ComPilot.
2. Voice dial A long press of the assigned button will start the voice dial which allows you to speak the person’s name instead of typing the number. I When using two phones at the same time (Multi Point) only the last paired phone can be used for voice dial. 3. Hold call While in a phone conversation, a long press of the assigned button will put the call on hold. The caller stays on the line but there is no audio transfer and the hearing aids switch to the previous hearing program.
5. Using the ComPilot for phone calls After holding or transferring a call, either a short press of the Main- or another long press of the assigned button transfers the call back to the ComPilot and the call is resumed through your hearing aids. 5.6 Using the external microphone Use the optional external lapel microphone “MC1” if you wear the ComPilot underneath clothing during a phone call. 1. Plug the 3.5 mm microphone plug into the audio input of the ComPilot.
2. Use the clip to place the omnidirectional microphone as close to your mouth as possible. 3. Put the neckloop around your neck and switch the ComPilot ON. Jackets, etc., will not negatively influence the wireless link to your hearing aids. 5.7 Locking the main button To prevent the Main button being accidentally pressed: Briefly press the Connect and Home button simultaneously to lock or unlock the Main button. When the Main button is locked, pressing it will have no effect.
6. Using the ComPilot as a remote control Important: The remote control functionality of the ComPilot is only available for wireless Spice Generation, Spice+ and Quest hearing aids. The streaming functionality is available for all wireless hearing aids. Please ask your hearing care professional for more information. I Before the remote control functionality can be used, your hearing care professional must enable the remote control.
J The neckloop is completely un-plugged and ComPilot is operated at arm’s length. No streaming is possible in this configuration. Make sure the ComPilot is switched ON. Volume change/FlexControl (optional) FlexControl helps you optimize clarity and comfort for different listening situations (optional on selected hearing aids).
6. Using the ComPilot as a remote control Program change Use the Main ( ) button to change hearing aid listening programs. Changing hearing aid programs is only possible if no streaming is in progress. Push the Home ( ) button to return to the startup hearing aid program and volume levels of your hearing aids. Press and hold the Home ( ) button (>2 sec) to select a favorite program (configured by the hearing care professional).
More remote control information: J Your hearing aids may beep to confirm that your selection was applied. J Both hearing aids are controlled at the same time. J Please ask your hearing care professional to print your personal ComPilot report. J The available hearing aid programs and volume levels are set by your hearing care professional. J The Power indicator is lit as long as you press a ComPilot button.
7. Using ComPilot with Roger / FM ComPilot can be used together with Roger or FM receivers through its direct audio input (Europlug). J Place the Roger / FM transmitter near the sound source and turn it on. J Attach your receiver to ComPilot via the Europlug socket as shown in the picture (turn receiver on if required). When a signal is detected, you will hear a beep notification through your hearing aids. J Press main button to accept the signal. J Press main button again to stop or resume the signal.
After 20 seconds the input will be put on hold automatically if you do not accept it. As long as a signal is received the hearing aid programs cannot be changed via the main button. If ComPilot does not receive a signal through the Europlug for 3 minutes, an alert will be heard.
8. More detailed information This section gives more insight in the following topics: 8.1. 8.2. 8.3. 8.4. 8.5. 8.6. 8.7. 8.8.
8.1 Wearing the ComPilot in different ways Standard To benefit from the streamer and remote control function, we recommend wearing the ComPilot around the neck. During calls your voice can only be picked up if the ComPilot is not covered by clothes. Handheld remote control To use the ComPilot as a remote control only, it can be held and operated in the hand. The neckloop must be removed in this case.
8. More detailed information 8.2 Managing multiple inputs to the ComPilot When an audio source is connected via the ComPilot, your hearing aids will automatically switch to special programs. Up to 4 automatic programs can be fine-tuned by your hearing care professional. It is possible to have multiple audio sources connected and in operation with the ComPilot: J Two Bluetooth devices (e.g., phone and TVLink S basestation). J One audio input (3.5 mm audio plug). J One FM receiver.
An audio source is considered as “connected” to the ComPilot if: J The audio plug is inserted (with or without audio signal). J A Roger/FM receiver is inserted and receives a Roger/FM signal. J A Bluetooth music source is streaming music or paused. J A Bluetooth phone is paired and within reach. I A phone call always has priority. You will hear the ringing indication even when listening to other audio sources via cable, Bluetooth or Roger/FM. If you reject or terminate the call, audio streaming will resume.
8. More detailed information Selecting one of multiple sources using the ComPilot With only one audio source (e.g., from a Bluetooth transmitter), each press of the Main ( ) button will pause or resume the audio source. Multiple sound sources can be accessed sequentially by pressing the Main ( ) button. After each press, the ComPilot selects the next connected source in a fixed sequence. Previously-active hearing program FM Europlug Bluetooth music 1 3.
Keep on briefly pressing the Main ( ) button until you reach your preferred audio source. ComPilot will announce each active audio source as you go through the sequence (VoiceAlerts). Pause streaming To temporarily interrupt streaming, e.g., if someone wants to speak to you, briefly press the Main ( ) button on the ComPilot as many times as needed until you hear the beeps announcing the previously-active acoustic hearing aid program.
8. More detailed information Streaming interruptions To avoid streaming interruptions, make sure you wear the ComPilot with the neckloop around your neck and keep the Bluetooth device within the operating range. Situations where streaming may be interrupted: J If the ComPilot is too far away from the hearing aids while streaming, e.g., if you are not wearing the neckloop or if you have unplugged the neckloop cable. J If the hearing aids are not worn correctly, e.g., if they are not in an upright position.
8.3 Resetting your ComPilot If, for some reason, the ComPilot becomes unresponsive: 1. Slide the ComPilot power switch to the ON position. 2. Press and hold the ( ), ( ) and ( ) button simultaneously for 2 seconds. 3. Slide the ComPilot power switch to the OFF position. 4. Wait for 5 seconds. The ComPilot is now reset and will resume normal operation when switching ON again. I After resetting the Bluetooth pairings, the configuration status and the grouping to the hearing aids are kept.
8. More detailed information 8.4 Summary of indicator lights The indicator lights provide helpful information as follows: Power indicator Charging Solid Red Charged and full battery Solid green Switching ON Green 2 seconds Switching OFF Red 2 seconds * Battery above 20% Blink green ** <20% battery remaining Short blink red ** * When switching the ComPilot OFF, the Power indicator may blink red first while the ComPilot is properly disconnecting all Bluetooth devices.
I After unplugging the neckloop the ComPilot enters power down mode after 2 minutes and the Power indicator goes off. Only the remote control functions can be used while the neckloop is unplugged. Battery state The color of the Power indicator informs you about the ComPilot battery state. The green Power indicator indicates a battery level > 20%. The red Power indicator indicates a battery level < 20%. Less than 1.5 hours streaming remain and the battery should be charged.
8. More detailed information Audio indicator The neckloop must be plugged in for any streaming. Plug or Roger/FM streaming Solid orange Bluetooth phone or music streaming 1 Bluetooth device connected 2 Bluetooth device connected In a phone call Solid blue Bluetooth pairing Very fast blue blinking Demo sound playing Solid violet Short blink blue Double-blink blue Solid blue I The Bluetooth pairing indication will be visible even if the neckloop is not plugged in.
I During cable or Roger/FM streaming, the Audio indicator will remain orange regardless of the Bluetooth connection state. 8.5 Introduction to Bluetooth What is Bluetooth? Bluetooth provides a way for devices like cellular or cordless phones, laptops and personal computers to communicate wirelessly. Your ComPilot supports Bluetooth to allow audio to be wirelessly received from many different audio devices and transmitted to your hearing aids.
8. More detailed information What Bluetooth devices can I use with my ComPilot? First, check whether the device you wish to use is Bluetooth-enabled: Look for the following symbol on the device or in its user guide. Second, the possible applications on a Bluetooth enabled device are defined by “profiles”. The device you wish to use with your ComPilot must support the appropriate Bluetooth profiles.
Bluetooth device compatibility If a problem occurs in the connection between your device and the ComPilot, or if you are unsure about your device’s Bluetooth capabilities, please consult your device’s user guide or ask your dealer. Bluetooth operating range Your ComPilot supports Bluetooth Class 2 operation up to a range of 10 meters (30 ft). When used with the TVLink S or TVLink II basestation for watching TV, the operation range is up to 30 meters (90 ft).
8. More detailed information If your Bluetooth device moves out of range of your ComPilot and has an active audio connection, this connection first starts to be intermittent and will finally be terminated. If the device is then moved back into range of your ComPilot, it may or may not resume streaming to your hearing aids. In this case, switch OFF the ComPilot and switch it ON again after the red Power indicator is turned off.
2. Connecting: Once a device is allowed to communicate with the ComPilot (“paired”) the connection procedure makes sure the devices can exchange audio signals. The paired devices connect every time they are switched ON and are within reach of each other. This is indicated on the ComPilot by the blue blinking Audio indicator. Most Bluetooth devices perform the connection procedure automatically after pairing. On the following pages the pairing and the connecting procedures are described.
8. More detailed information 8.6 Setting up Bluetooth This section describes the pairing and connection procedure for Bluetooth devices. Step-by-step: pairing a Bluetooth-enabled phone I It is only necessary to perform the pairing procedure once with each Bluetooth device. The pairing procedure is controlled by your phone. I Different phones have different menu structures.
1. Turn ON your ComPilot and the phone. Place them next to each other. 2. Locate the connectivity settings in your phone menu. Look for the Bluetooth feature. 3. On your phone, ensure that the Bluetooth feature is turned on. 4. On your phone choose SEARCH to search for Bluetooth devices or audio enhancements. 5. To initiate the pairing process on your ComPilot, press and hold the ( ) and ( ) buttons simultaneously for 2 seconds until the Audio indicator starts to rapidly blink blue. 2 sec 6.
8. More detailed information 8. Your phone may then ask you to enter a passcode. If so, enter “0000” (four zeros). Some phones may ask which Bluetooth service you want to enable. Select “Headset” or, if available, “Stereo Headset”. 9. Your ComPilot should now be paired to your phone and the Audio indicator will stop blinking. I The pairing process is independent from the neckloop (it can be plugged in or not). I It may be necessary to redo the pairing if your phone’s firmware was updated.
1. Ensure that the ComPilot is turned ON and the neckloop is plugged in and worn correctly. 2. Locate the Bluetooth section in your phone menu and select list of “Paired devices”. 3. Locate and highlight your ComPilot and select “Connect”. 4. Confirmation of successful connection is indicated on the ComPilot by the Audio indicator blinking blue. Additionally a headset symbol ( ) may appear on the main screen of your phone.
8. More detailed information Pairing with other external Bluetooth devices If you want to use your ComPilot to listen to music from your stereo system you may use an external Bluetooth transmitter. The ComPilot can also be used with a Bluetooth-enabled landline phone. I The pairing procedure for other Bluetooth devices is controlled by the device with which you are attempting to pair. The procedure for pairing may vary for each device.
5. Your ComPilot will remain in the pairing mode for two minutes or until the pairing is completed. 6. If a passcode is required, enter “0000” (four zeros). After pairing, wait until the devices have completed connection. Confirmation of successful connection is indicated on the ComPilot by the Audio indicator shortly blinking blue. A double-blink indicates that two devices are connected to ComPilot.
8. More detailed information Deleting the pairing of Bluetooth devices removes the ability to connect to any previously paired Bluetooth device. You will need to perform the pairing process again if you wish to reconnect. 8.7 Caller identification: spoken caller names The ComPilot is able to tell you the name of the caller. If your phone supports Phone Book Access (PBA) or Phone Book Access Profile (PBAP), the ComPilot will try to access information about the caller every time the phone rings.
To make sure the pronunciation is correct your hearing care professional can configure the language settings of your ComPilot. The phonebook is not downloaded to the ComPilot. This way, ComPilot can also support the use of different phones. Please consult your phone’s user guide or the phone dealer to check whether this feature is supported by your phone. 8.8 VoiceAlerts: spoken ComPilot status VoiceAlerts inform you about the different operation modes and status of the ComPilot using text-to-speech.
8. More detailed information J Standard: Additional information about switching ComPilot ON or OFF, start or end charging during streaming, input channel confirmation and FM announcements. J Detailed: Additional information about start or end of charging even if no streaming source is active, external microphone connection, Bluetooth device connect or disconnect and transfer or hold a call. I A new ComPilot is always delivered with English speech messages (VoiceAlerts) on speech level “Standard”.
9. Troubleshooting ComPilot A summary of frequently asked questions and their answers: Most probable cause Remedy During Bluetooth pairing my other device is prompting for a code, what do I have to enter? J The pairing code is required for the initial coupling of ComPilot with your Bluetooth device (“pairing”). J The ComPilot pairing code is “0000” (four zeros). I hear intermittency during an audio transfer via ComPilot. J The Bluetooth device is too far away, or worn in a back pocket (body shielding).
9. Troubleshooting ComPilot Most probable cause Remedy I have difficulties understanding the phone conversation in a noisy environment. J Your hearing aid microphones are set too high during the call. J Reduce the hearing aid volume by pressing the button. J If the sound volume over the phone (or music) is too low after this reduction use the phone volume button to increase the volume. The caller can hear me but I cannot hear the caller. J The call was transferred to your phone.
Most probable cause Remedy J Pairing was deleted. J Repeat the pairing between ComPilot and the Bluetooth device which was deleted. I am not streaming but the hearing aids keeps switching between the Bluetooth and the normal hearing aid program. J Your phone sends sounds to ComPilot due to incoming SMS or mails. J Phone key tones are switched on. J Disable the system sounds for reminders, alarms, SMS, etc. via your phone menu. J Switch off phone key tones via your phone menu.
9. Troubleshooting ComPilot Most probable cause Remedy Every time I get in my car the ComPilot connection to my phone shows unexpected behavior. J The car Bluetooth system connects to your phone. J Consider disconnecting the car system from your phone. I accepted the incoming phone call but cannot hear the call in my hearing aids. J Some phones, when accepting the call through the phone button, don‘t use ComPilot. J Always accept the call by pressing the ComPilot Main ( ) button.
Most probable cause Remedy J ComPilot is not paired to the phone. J The distance is too great between ComPilot and the phone. J Follow the pairing process in this guide. J Wear ComPilot around your neck. Keep distance to phone <5 m (15 ft). The phone is ringing, the Audio indicator is solid blue but there is no ringing signal through the hearing aids. J ComPilot is out of range of the hearing aids. J Phone is set to vibrate. J You are already having a phone call, then a second call cannot be recognized.
9. Troubleshooting ComPilot Most probable cause Remedy During a phone call the other party reports difficulties hearing me. J ComPilot microphone openings may be covered. J ComPilot may not be worn correctly. J ComPilot may rub against clothing. J The surrounding noise may be too loud. 70 J Make sure the microphone openings are not covered by part of your body, clothing or dirt and debris. J Do not turn ComPilot sideways and make sure the neckloop plugs point towards your mouth as you speak.
Most probable cause Remedy ComPilot is unresponsive or does not show any indicator when switching ON. J ComPilot may be completely discharged. J It may indicate a software problem. J Charge your ComPilot for at least 1 hour. J Unplug any connectors from ComPilot. J Switch ComPilot OFF and ON again. J Consider resetting ComPilot. Press the Connect button (<>) and Volume up (+) and Volume down (-) at the same time. The operating time of your ComPilot is reduced substantially.
10. Important safety information Please read the information on the following pages before using your Phonak ComPilot. 10.1 Hazard warnings ! Keep this device out of reach of children under 3 years. ! Phonak devices may generate magnetic fields. Tests that Phonak conducted showed that no interferences with the Implantable devices (e.g. pacemakers, defibrillators, etc.) were caused that would impact the safe and effective use of the Implantable devices.
! Make sure to always remove both plugs of the neckloop and other cables when using the ComPilot as a handheld remote control. ! Opening the ComPilot might damage it. If problems occur which cannot be resolved by following the remedy guidelines in the troubleshooting section of this user guide, consult your hearing care professional. ! The ComPilot may only be repaired by an authorized service center. Changes or modifications to the device that were not explicitly approved by Phonak are not permitted.
10. Important safety information ! External devices may only be connected if they have been tested in accordance with corresponding IECXXXXX standards. Only use accessories approved by Phonak AG to avoid any electrical shock. ! Using your ComPilot cables in any way contradictory to their intended purpose (e.g., wearing the USB cable around the neck) can cause injury. ! When operating machinery, ensure that no parts get caught in the machine. ! The mini-USB port is to be used for the described purpose only.
! Caution: electric shock. Do not insert plug alone into electrical outlets. 10.2 Information on product safety I Protect the ComPilot from excessive moisture (bathing, swimming), heat (radiator, car dashboard), and direct skin contact when sweating (workout, fitness, sport). II Special medical or dental examination including radiation described below, may adversely affect the correct functioning of your hearing aids.
10. Important safety information I Do not drop the device. Dropping onto a hard surface can damage your device. I Do not use excessive force when connecting your ComPilot to the different cables. I Protect the device connectors, plugs, charging slot and power supply from dirt and debris. I Keep the device at least 10 cm away from any kind of magnets. I Clean the device using a damp cloth. Never use household cleaning products (washing powder, soap, etc.) or alcohol to clean the device.
strong electromagnetic fields, it may be necessary to be at least 60 cm (24”) away from the interfering device to ensure proper operation. I Do not disconnect the neckloop while the ComPilot is transmitting signals to your hearing aids. I For safety reasons, recharge the ComPilot only with chargers supplied by Phonak or by USB-certified chargers >500 mA. I Do not connect an USB or audio cable exceeding 3 meters (9 ft) in length to the ComPilot.
10. Important safety information 10.3 Other important information I High-powered electronic equipment, larger electronic installations and metallic structures may impair and significantly reduce the operating range. I If the hearing aids do not respond to the ComPilot because of an unusual field disturbance, move away from the disturbing field.
11. Service and warranty 11.1 Local warranty Please ask the hearing care professional, where you purchased your ComPilot, about the terms of the local warranty. 11.2 International warranty Phonak offers a one year limited international warranty, valid as of the date of purchase. This limited warranty covers manufacturing and material defects. The warranty only comes into force if proof of purchase is shown.
10. Service and warranty 11.3 Warranty limitation This warranty does not cover damage from improper handling or care, exposure to chemicals, immersion in water or undue stress. Damage caused by third parties or non-authorized service centers renders the warranty null and void. This warranty does not include any services performed by a hearing care professional in their office.
12. Compliance information Europe: Declaration of Conformity Hereby Phonak AG declares that this Phonak product is in compliance with the essential requirements of the Medical Devices Directive 93/42/EEC as well as the Radio and Telecommunications Terminal Equipment Directive 1999/5/EC. The full text of the Declaration of Conformity can be obtained from the manufacturer or the local Phonak representative whose address can be taken from the list on http://www.phonak.com (worldwide locations).
12. Compliance information Notice 1: This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Notice 2: Changes or modifications made to this device not expressly approved by Phonak may void the FCC authorization to operate this device.
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: J Reorient or relocate the receiving antenna. J Increase the separation between the device and receiver.
13. Information and explanation of symbols With the CE symbol, Phonak AG confirms that this Phonak product meets the requirements of the Medical Devices Directive 93/42/EEC as well as the R&TTE Directive 1999/5/EC on radio and telecommunications equipment. This symbol indicates that the products described in these user instructions adhere to the requirements for an application part of Type B of EN 60601-1. The surface of the device is specified as applied part of Type B.
This symbol indicates that it is important for the user to read and take into account the relevant information in this user guide. This symbol indicates that it is important for the user to pay attention to the relevant warning notices in these user guides. Important information for handling and product safety. EMC and Radiocommunications compliance label Australia.
13. Information and explanation of symbols Transport and storage conditions Humidity transportation: Up to 90% (non condensing). Humidity storage: 0% to 70%, if not in use. Atmospheric pressure: 200 hPA to 1500 hPa. Temperature transport and storage: –20° to +45° Celsius (–4° to +113° Fahrenheit). Temperature operation: 0° to +45° Celsius (+32° to +113° Fahrenheit). Keep dry.
The symbol with the crossed-out garbage bin is to make you aware that this device may not be thrown away as normal household waste. Please dispose of old or unused device, at waste disposal sites intended for electronic waste, or give your device to your hearing care professional for disposal. Proper disposal protects the environment and health. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Phonak is under license.
www.phonak-us.com 029-0237-02/V3.
