AN-CP65 Cell Phone Signal Booster User Manual 1 / 11
Introduction With the popularity of mobile communications, people want to make a call anytime, anywhere, so the coverage requirement of communication network is higher and higher, but the reality is not so, sometimes mobile phone signal is not very good, you want to make a smooth call, even in some places cell phone cannot dial out. in this cases, cell phone signal booster can solve this problem in a certain extent.
compliance. Do not remove the covers during working. Do not try to repair or replace any components inside of the equipment. Alteration or abuse of the equipment or other components will void this product’s warranty, and could be dangerous to the user. PACKAGE CONTENTS 1 2 1. 1Pcs AN-CP65 Booster with SMA Female connectors. 2. AC/DC Power Adaptor. 3. Screws Mounting Kits. 4. User manual (this document).
Indoor Cable 20 feet 3D-FB Coaxial PTE-3D-FB-5NB cable with N male 2.19db @824-894MHz 2.55db @1850-1990MHz connector Outdoor Cable 50 feet 3D-FB Coaxial PTE-3D-FB-10NB cable with N male 5.49db @824-894MHz 6.25db @1850-1990MHz connector Notes：The above model antennas are suitable for AN-CP65 booster. Warning：Unauthorized antennas，cables and/or coupling devices are prohibited by FCC rules.
antenna is installed The phone calls or data transmission shall be smooth and stable by 3 times testing in location where the outdoor antenna is to be installed As shown from the above illustration, testing the signals from A to E, and select a best place that displays full bar signals to install the outdoor antenna. Selecting the installation direction of outdoor antenna. The outdoor antenna shall point to the direction of the tower, and it would be much better to keep line of sight.
If isolation can’t be achieved by the limited distance, the roof of the building or any other barriers can be used in between to increase isolation. Fix the donor antenna after selecting the best position, and adjust slightly its height or angles in order to get the signals with suitable input power level and calling quality. （2）Installation of Indoor Antenna Proper antennas shall be selected according to the site conditions and the requirement.
Connect power adaptor to the booster，connect The other end of power adaptor to the power outlet. WARNING: The input voltage for the booster is +5V DC. DO NOT use this Booster with a regular power supply that NOT +5V . otherwise, it will be damaged and the user may also be injured. TROUBLESHOOTING AND SUPPORT Problem Resolution LED is not light 1.Find an alternate power adaptor and try again. 2.Check the power outlet, the power adapter plug maybe is poor connected. 3.
following methods: E-mail: support@PHONETONE-tech.com If you want to know about PHONETONE Company and products for more information, please visit at: www.PHONETONE.com Consumer booster warning label: A subscriber must have the consent of a wireless provider to operate a Consumer Signal Booster. Subscribers may obtain provider consent in a variety of ways.
engineer to handle inquiries. They may eventually allow consumers to register on their website but they want to gauge how the process works via phone first. ● T-Mobile online registration link: (www.T-Mobile.com/BoosterRegistration); (https://saqat.t-mobile.com/sites/SignalBooster#). ●Verizon’s online registration link: (http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html). ● AT&T will allow online registration and will inform OET Lab with the weblink when it is ready. ●U.S.
Copyright Information © 2018 Copyright PHONETONE Technology (Shenzhen) Co., Ltd. The information contained in this document is subject to change without notice. Edition 8, 5/2018 FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
The term “IC: “ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications. Le présent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio exempts de licence.
