PRM92K20CE UHF RFID Module User’s Manual
PRM92x20CE USER’s MANUAL – PRM92x20CE_ADK01 Contents 1 2 2.1 2.2 3 3.1 4 5 Revision History ................................................................................................................................3 Introduction .......................................................................................................................................4 Package configuration ....................................................................................................................
PRM92x20CE USER’s MANUAL – PRM92x20CE_ADK01 1 Revision History Version Date Description ADK01 2012.10.
PRM92x20CE USER’s s MANUAL – PRM92x20 0CE_ADK01 1 2 Intro oduction The PRM92xx20CE DK consists c of PR RM92x20CE E and PRM9x x10C_CTRL board. The PRM9x10C_ _CTRL board d supports DC C power supp ply and PC in nterface. PRM92x20C CE is UHF RFID reader module m using g PR9200 an nd include TC CXO. Figure 1 Co onnection to P PRM92x10C C_CTRL & PR RM92x20CE E 2.
PRM92x20CE USER’s MANUAL – PRM92x20CE_ADK01 2.2 Features PRM92x20CE is reference designed module of PR9200 and low cost components. PRM9x10C_CTRL is control board that connects Reader Module to PC, supporting USB-to-UART interface and DC power management for reader module. PRM92x20CE - EPC Gen2 support - RCP protocol with CRC - FCC,EN certified - PR9200, TCXO, Coupler, Antenna port - Module size : 30mm x 35mm - U.
PRM92x20CE USER’s MANUAL – PRM92x20CE_ADK01 3 DK description 3.1 PRM92x10C_CTRL Figure 2 3.1.1 Power connector ① This is 3-pin connector for power supply to internal LDO of this module (⑨) If this connector is connected by jumper, PRM92x20CE is powered by USB 5V. Also you can connect external power through this connector pin. (A) When USB power is used (Default) (B) When External power is used Figure 3 Power connector 3.1.
PRM92x20CE USER’s MANUAL – PRM92x20CE_ADK01 3.1.3 SWD port ③ In order to debug or firmware download, this SWD port is connected to H/W debugger such as ULINK2 and XLINK (A) X-LINK port (B) ULINK2 port Figure 4 SWD port [Notice] SWD port power (3.3V) is provided by ULINK2 or X-LINK adapter. Please check jumper setting of adapter (refer to ULINK2 user’s guide, http://www.keil.com/support/man/docs/ulink2/ulink2_hw_jumpers.htm) 3.1.4 LED part ④ PRM9x10C_CTRL has two LED.
PRM92x20CE USER’s MANUAL – PRM92x20CE_ADK01 3.1.7 Application connector ⑦ 12 P07_SPI_CS 14 SWDIO 16 SWCLK 18 NC 20 NC 22 GND 24 GND 26 GND 28 GND 30 GND P12_SCL 13 P13_RXD1 15 P14_TXD1 17 GND 19 P15 21 P16 23 P17 25 ISP_MODEb 27 CSE 29 10 P06_SPI_CLK 9 P10 P11_SDA 11 P05_SPI_RXD 8 P04_SPI_TXD 6 5 P01_TXD0 7 P03 4 3 GND GND 2 1 VCC36 P00_RXD0 User can connect GPIO, SPI, I2C through application connector and use PRM92x20CE MCU all IO function. This connector has 2.54mm pitch.
PRM92x20CE USER’s MANUAL – PRM92x20CE_ADK01 4 Specifications Parameter Symbol Min PRM92x10C_CTRL supply voltage PRM92x10C_CTRL output voltage PRM92x10C Current consumption in active mode TX output maximum power 1 Frequency range VDD_36 Typ V 3.6 V 550 POUT 25 917.1 Unit 5 IOP fC Max mA dBm 926.9 MHz 1. Current board max power is about 25dBm.
PRM92x20CE USER’s MANUAL – PRM92x20CE_ADK01 5 Address Information PHYCHIPS Inc. #204 Migun Techno world 1, 533 Yongsan-dong, Yuseong-gu, Daejeon, Korea, 305-500 http://www.phychips.com sales@phychips.com Tel: +82-42-864-2402 Fax: +82-42-864-2403 Disclaimer: PHYCHIPS reserves the right to make changes to the information in this document without prior notice. The purchase of PHYCHIPS products does not convey any license under patent rights owned by PHYCHIPS or others.
PRM92x20CE USER’s MANUAL – PRM92x20CE_ADK01 [Appendix1] Channel Number Table 1. US band Channel Channel Frequency Channel Channel Frequency 1 917.10 MHz 26 922.10 MHz 2 917.30 MHz 27 922.30 MHz 3 917.50 MHz 28 922.50 MHz 4 917.70 MHz 29 922.70 MHz 5 917.90 MHz 30 922.90 MHz 6 918.10 MHz 31 923.10 MHz 7 918.30 MHz 32 923.30 MHz 8 918.50 MHz 33 923.50 MHz 9 918.70 MHz 34 923.70 MHz 10 918.90 MHz 35 923.90 MHz 11 919.10 MHz 36 924.10 MHz 12 919.30 MHz 37 924.
PRM92x20CE USER’s MANUAL – PRM92x20CE_ADK01 [Appendix2] FCC Certification Requirements 1. Caution Any changed or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate this equipment. 2. OEM installation guide I. OEM integrators must be instructed to ensure that the end-user has no manual instructions to remove or install the module. II. This module is to be installed only in mobile of fixed devices.
