Instruction Manual

ManualsBrandsPIAA ManualsLightingRS600 H.I.D. Shock Lamp

Shock Lamp RS600 H.I.D.

Installation Instructions

Thank you very much for purchasing this PIAA product.

Please read the entire manual before installation and use of this product.

FOR INSTALLERS

Please give this installation manual to customer after installing.

When installing two lamps on the vehicle, it is necessary to purchase another relay harness

(PN 34035). One harness is required for each lamp.

• Lighting laws vary from state to state.

Check your local laws before use.

• The lamps get very hot when they have been in use.

Do not touch them as they may cause burns.

• After the lights have been on, do not place them near ammable objects.

• Do not splash water directly on the hot lamps, as this may cause cracking of the lens due

to dramatic change in temperature.

• To avoid potential damage to your eyes, do not look directly into the lamp.

• This product is designed for 12V automotive electrical systems only.

• Using this light system while the engine is not running will drain the battery.

• Do not repeatedly turn the light system on and o as it will shorten the life of the system.

• To avoid potential damage to your lights, make sure your lights are turned on prior to

starting or shutting o your vehicle.

• Using the wrong bulbs may cause a malfunction. Use only specied PIAA bulbs.

• When changing bulbs or lenses follow the lamp assembly/disassembly diagram.

WARNING

Summary of content (12 pages)

PAGE 1
Shock Lamp RS600 H.I.D. Installation Instructions Thank you very much for purchasing this PIAA product. Please read the entire manual before installation and use of this product. For Installers Please give this installation manual to customer after installing. When installing two lamps on the vehicle, it is necessary to purchase another relay harness (PN 34035). One harness is required for each lamp. WARNING • Lighting laws vary from state to state. Check your local laws before use.
PAGE 2
WARNING • When activated, this system operates at extremely high voltage (20,000V). DO NOT turn on the switch when holding the cord that connects the ballast and the lamp! • Use of damaged or incorrect wiring may cause this product to malfunction and/or cause an electrical fire. • Remember that this product operates at extremely high voltages. Make sure your hands and work area are clean and dry to avoid injury from electrical shock.
PAGE 3
CONTENTS * Make sure that all parts are in the package. If something is missing, please contact the store where you purchased the product. One (1) Lamp assembly. One (1) rubber cushion.
PAGE 4
LAMP INSTALLATION 1. For lamp installation, a hole with a diameter of 14mm is required. Make necessary preparation such as installation of lamp bracket. Flat washer Spring washer Nut caution • When using a commercially supplied lamp bracket, before removing the bolt that is already installed on the car body, make sure that it is safe to do so. • The lamp should be mounted in an area sufficient to support its size and weight.
PAGE 5
HARNESS INSTALLATION When connecting the wires on the harness, follow the wiring diagram and the sequence below. 1. Before connecting any wires, disconnect the negative (-) battery terminal. Note: When running the wires through the engine compartment be sure to keep them securely away from moving parts such as the fan and the throttle cable and away from hot parts such as the exhaust manifold. 2. Pull the connector for the relay harness switch into the car and connect it to the switch harness. 3.
PAGE 6
WIRING DIAGRAM 6
PAGE 7
DRIVING LIGHT AIMING Typically, driving lights are mounted above the front bumper about 14-30 inches from the ground to provide extra high beam illumination. Driving lights can be mounted below the bumper, although they will not be as efficient because the light will hit the ground sooner and reduce the range of the light. Visual aim is made with the center of the beam not spot 1.5 inches below the lamp center at 25 feet with the lamp facing straight forward (see below).
PAGE 8
Disassembly 1. Pry white cover off lamp at the arrow location on the black housing. 2. Unscrew the black (BK) frame. 3. Remove L&R&BK frame unit. 4. Unplug 2 bulb plugs.
PAGE 9
5. L&R&BK frame unit... 6. Unscrew 6 screws on the L&R&BK frame unit and take L&R unit away from the B&K frame. (Note: No need to unscrew this if you are only changing the bulb!) 7. Unscrew the little screws that mount the bulb. 8.
PAGE 10
NOTES 10
PAGE 11
PAGE 12
PIAA LIMITED WARRANTY With the exception of bulbs, PIAA Corporation, USA (“PIAA”) warrants its products to be free from defects in workmanship and materials under normal use for as long as the original purchaser owns them. EXCLUSIONS This Limited Warranty specifically excludes defects resulting from misuse, abuse, neglect, alteration, modification, improper installation, unauthorized repairs, submersion, theft, vehicle crash, or by any other type of impact.