Instruction Manual Book ITEM CODE: BH99. SPECIFICATION Wingspan : 2,850 mm Length : 1,910 mm Weight : 8.1 kg 112.20 in. 75.20 in. 17.82 lbs. Parts listing required (not included): Radio : 06 channels. Servo : 08 standard high torque servos. Engine : 35 CC gas(FUJI IMVAC). Made in Vietnam.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual This instruction manual is designed to help you build a great flying aeroplane. Please read this manual thoroughly before starting assembly of your FIESELER Fi156C STORCH. Use the parts listing below to identify all parts. WARNING Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU ASSUME ALL RISK & RESPONSIBILITY.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Caution: this model is not a toy! If you are a beginner to this type of powered model, please ask an experienced model flyer for help and support. If you attempt to operate the model without knowing what you are doing you could easily injure yourself or somebody else. Please keep your safety and well-being in mind at all times.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual REPLACEMENT SMALL PARTS 5. 6. 5a. 6a. 5b. 6b. 5c. 6c. 5d. 6d. 5e. 5F. 3. 4. 7. 1. 2. 8. 1. Wheels. 2. Fuel Tank. 3. Ruler wing. I. AILERON. 1.INSTALLING THE AILERON SERVOS. 1) Install the rubber grommets and brass eyelets onto the aileron servos. 4. Plastic parts for rudder pushrod. 5. Landing gear struts. 6. Wing struts set. 7.Tail gear set. 8. Vertical stabilizer struts.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual Secure Repeat the procedure for the other wing half. INSTALLING THE AILERON CONTROL HORN . Secure 3) Using the thread as a guide and using masking tape, tape the servo lead to the end of the thread: carefully pull the thread out. When you have pulled the servo lead out, remove the masking tape and the servo lead from the thread. 4) Drill 1,6mm pilot holes through the block of wood for each of the four mounting screws provided with the servo.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual Ruler wing. Secure. Top side Bottom side 2. INSTALLING THE FLAP SERVO . Electric wire Thread 3.INSTALLING THE AILERON LINKAGES. Installing the aileron linkages as pictures below. M3 lock nut 2x12mm.
FIESELER Fi156C STORCH - ITEM CODE: BH99. INSTALLING THE FLAP CONTROL HORN. Instruction Manual INSTALLING THE FLAP LINKAGES. Installing the aileron linkages as pictures below. 3 x 20 mm.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual Drill a hole 8mm diameter Secure Front view INSTALLING THE ENGINE. Bottom side 5 x 70mm Repeat the procedure for the other wing half. INSTALLING THE ENGINE MOUNT.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual Throttle cable. Secure Left side INSTALLING THE THROTTLE CABLE. 1. Install one adjustable metal connector through the third hole out from the center of one servo arm, enlarge the hole in the servo arm using a 2mm drill bit to accommodate the servo connector. Remove the excess material from the arm. Throttle cable. After installing the adjustable metal connector apply a small drop of thin C/A to the bottom nut.
FIESELER Fi156C STORCH - ITEM CODE: BH99.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual 4 3x12mm 3 4 Secure 3x12mm 4 4 Secure Secure 4 4 INSTALLING THE BATTERY. Tie wrap.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual Battery. Tygon gas tubing not included. Vent tube Fuel pick- up tube FUEL TANK. INSTALLING THE STOPPER ASSEMBLY 1) The stopper has been pre-assembled at the factory. 2) Using a modeling knife, cut one length of silicon fuel line (the length of silicon fuel line is calculated by how the weighted clunk should rest about 8mm away from the rear of the tank and move freely inside the tank).
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual Do not secure the tank into place permanently until after balancing the airplane. You may need to remove the tank to mount the battery in the fuel tank compartment COWLING. 1) Slide the fiberglass cowl over the engine and line up the back edge of the cowl with the marks you made on the fuselage. Top side. Bottom side. Blow through one of the lines to ensure the fuel lines have not become kinked inside the fuel tank compartment.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual Trim and cut Top side. Front view. Bottom side. Trim and cut INSTALLING THE ELEVATOR AND RUDDER SERVOS. 3 x 12mm Machine screw. Left side. Elevator servo. Elevator servo. Bottom side. 14 Throttle Servo.
FIESELER Fi156C STORCH - ITEM CODE: BH99. HORIZONTAL STABILIZER. Horizontal stabilizer installation Instruction Manual 9. 230 mm See picture below. Top side 4x12 mm Secure.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual Bottom side. ELEVATOR CONTROL HORN AND ELEVATOR PUSHROD INSTALLATION. Elevator control horn install as same as the way of aileron control horn. Please see pictures below. 3x20mm. Plastic parts of elevator pushrod. Cut.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual VERTICAL INSTALLATION. Rudder servo install as same as method of elevator servo. See picture below: Ru se dde rvo r . C/A glue Elevator pushrod. Elevator pushrod. Horizontal Stabilizer. 90º Vertical Stabilizer. A+B Epoxy PLUS glue.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual Secure Rudder control horn. Top side Bottom side RUDDER CONTROL HORN INSTALLATION. Rudder control horn install as same as the way of aileron control horn. Please see pictures below. Control horn of Rudder. Ru dd er se rvo . RUDDER PUSHROD INSTALLATION. 1. Rudder pushrod install as same as the way of aileron control horn. 2. Rudder push - pull system install as same as picture below. 3 x 30 mm 3 x 12mm Secure.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual C/A glue Secure. Bottom side 3x12mm MOUNTING THE TAIL WHEEL BRACKET. Secure.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual Bottom side Vertical Stabilizer Struts. Top side 3x15mm INSTALLING LANDING GEAR. PARTS REQUIRED 6a 5a 1. 5b 6b 6c 5c 5d 5e Secure. Secure.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual 5d 3x10mm 5c Secure. 5d 5b 5c Secure. Secure.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual 5F 3x10mm Secure. 5F Secure. 5d Secure. 3x10mm 5e 5a 5e 5e 5F 5F 5d 5c 5d 5b 5c INSTALLING THE RECEIVER AND BATTERY. Secure. Secure. 1. Plug the servo leads and the switch lead into the receiver. You may want to plug an aileron extension into the receiver to make plugging in the aileron servo lead easier when you are installing the wing . Plug the battery pack lead into the switch. 2.
FIESELER Fi156C STORCH - ITEM CODE: BH99. 4. Using a 2mm drill bit, drill a hole through the side of the fuselage, near the receiver, for the antenna to exit. Instruction Manual WING ATTACHMENT. Locate the aluminium wing dihedral brace. 12 19 Tie wrap. 890 mm Re ce *** Test fit the aluminium tube dihedral brace into each wing haft. The brace should slide in easily. If not, use 220 grit sand around the edges and ends of the brace until it fits properly. ive r 19 UB EC 12 Right wing.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual PILOT INSTALLATION. Bottom side 7 6b 3x15mm Top side Secure WING STRUTS INSTALLATION 6a 6b 3x15mm.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual 7 3x12mm 6b 3x10mm Secure. Secure. Secure. 3x15mm Bottom side Secure. Bottom side 6b 6a Secure.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual 115 Top side BALANCING. 1) It is critical that your airplane be balanced correctly. Improper balance will cause your plane to lose control and crash. THE CENTER OF GRAVITY IS LOCATED 115MM BACK FROM THE LEADING EDGE OF THE WING. 2) Mount the wing to the fuselage. Using a couple of pieces of masking tape, place them on the top side of the wing 115mm back from the leading edge, at the fuselage sides. 3. Turn the airplane upside down.
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual PRE-FLIGHT CHECK. 1) Completely charge your transmitter and receiver batteries before your first day of flying. 2) Check every bolt and every glue joint in your plane to ensure that everything is tight and well bonded. 3) Double check the balance of the airplane. 4) Check the control surface. 5) Check the receiver antenna . It should be fully extended and not coiled up inside the fuselage. 6) Properly balance the propeller.
