Instructions for use

ManualsBrandsPichler ManualsARF aircraftSuper Cub (Burda Squadron) / 1620mm

Table Of Contents

PIPER PA-18

Radio control model

R/C Flugmodell

MONTAGEANLEITUNG

Designed for brushless electric motors (.46-.52 class glow conversion optional)

Entwickelt für Brushless Elektro Motoren (7,5 -8,5cc Glühzündermotor Einbau möglich)

INSTRUCTION MANUAL

SPECIFICATIONS

Wingspan 63.7in.

Length 49.2 in.

Electric Motor (See next page)

Glow Engine .46 2Stroke / .52 4-Stroke

Radio 5 Channel / 4 -5 Servos

WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.

Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann

hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um

professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist

durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

TECHNISCHE DATEN

Spannweite 1620mm

Lange 1250mm

Elektroantrieb (siehe nächste Seite)

Verbrennerantrieb 7.5cc 2-T / 8.5cc 4-T

Fernsteuerung 5 Kanal / 4 -5 Servos

SUPER CUB

Floats available as an option! (No. C4682)

Schwimmer als Sonderzubehör erhältlich! (Best.Nr.C4682)

Summary of content (16 pages)

PAGE 1
Radio control model R/C Flugmodell INSTRUCTION MANUAL MONTAGEANLEITUNG PIPER PA-18 SUPER CUB Designed for brushless electric motors (.46-.52 class glow conversion optional) Entwickelt für Brushless Elektro Motoren (7,5 -8,5cc Glühzündermotor Einbau möglich) Floats available as an option! (No. C4682) Schwimmer als Sonderzubehör erhältlich! (Best.Nr.
PAGE 2
RECOMMENDED ACCESSORIES (Purchase separately) Empfohlenes Zubehör (Nicht im Lieferumfang enthalten) Egänzungskit Verbrenner (Tank + Motorträger) Best.Nr. C4165 Antrieb Standard: BOOST 40 Brushless Combo Set, Best.Nr. C2983 LiPo Battery RED POWER 3200-3S, Best.Nr. C3164 Luftschraube 12*6, Best.Nr. C1937 1 x Servo S4020 (für Seitenruder) Best.Nr. C1687 Antrieb Tuning (Kraftvoller Kunstflug): BOOST 60 Brushless Combo Set, Best.Nr. C3174 LiPO Akku RED POWER 4250-5S, Best.Nr. C4547 Luftschraube 13*8, Best.Nr.
PAGE 3
1 A Align the mark on both mounts with the center mark on the fire-wall Securely attach the engine mount to the fire-wall using the four 4x25mm screws. ! Note the side thrust for motor! Sturz und Zug beachten! A 102mm FRONT VIEW the engine on the engine mount beams so the B Position distance from the prop hubto the fire-wall is 102mm/(4”). Using a pencil, mark th engine mounting plate where the four holes are to be drilled. Note: Mark the mounting plate through the engine mounting flanges.
PAGE 4
2 B A C 13/64” 5mm D Using a plywood motor mounting plate as a template, mark the fire wall where the four holes are to be drilled . Remove the plywood motor mounting plate and drill a 13/64”(5mm) hole through the fire-wall at each of the four marks marked above. Push the four 5x35mm bolts through the fire-wall as shown (5). Reposition the plywood motor mounting plate and secure it in place with twelve 5xmm nuts and washers (6).
PAGE 5
3 2.5x8mm screw ............3 2.mm 2.mm 2.mm Cut two slots (3x7mm and 3mm deep) along the trailing edge of the horizontal stabilizer. 4 TOP VIEW / Draufsicht HORIZONTAL STABILIZER TOP VIEW / Draufsicht 85mm 5 4mm 4mm 85mm the elevator out of the horizontal stabilizer.
PAGE 6
you are satisfied with the alignment, 6A When use a pencil to trace around the top and 6 bottom of the stabilizer where it meets the fuselage. Cut away only the covering both side the horizontal stabilizer from the fuselage. 6B Remove Using the sharp hobby knife, carefully cut away the covering inside the lines which were marked above. * WARNING: When removing any covering from the airframe, please ensure that you secure the cut edge with CA or similar cement. This will ensure the covering remain tight.
PAGE 7
CA 8 10mm CA Cut a slots (3x7mm and through both the covering and balsa wood) along the trailing edge of the vertical stabilizer. Cut away only the covering FRONT-VIEW Trial fit the vertical stabilizer in place. Check the alignment of the vertical stabilizer. If the parts will join, but with a gaps, sand or trim the parts a little at a time until the parts meet exactly with no gaps.
PAGE 8
Collar 9 0.5~0.6in. 12~15mm 0.3in. 8mm 1/8(3mm) screw CA 1/16 1.5mm Cut away the covering and balsa wood BOTTOM - VIEW / Unteransicht 1/16 1.5mm 3x12..........2 ........................1 ........................1 10 4X20mm screw ............4 Cut away only the covering * WARNING: When removing any covering from the airframe, please ensure that you secure the cut edge with CA or similar cement. This will ensure the covering remain tight.
PAGE 9
12 3mm connector 3mm connector Connector ......4 3mm connector Aluminum landing gear Hauptfahrwerk 13 BOTTOM - VIEW / Unteransicht 4mm 4mm washer 4mm nut 4X40mm screw AUSTRIA VERSION VQA083 4x40mm screw ............
PAGE 10
14 15 ...
PAGE 11
17 Tipp X Magnetic seating (front seating only) 18 Magnetic piece. CA Battery seat bell Akku Kiettband aus dem PICHLER Sortiment Best.Nr.
PAGE 12
19 CA B’ B Aluminum tube Aluminum tube B=B’ Note: check the length (B=B’) of the aluminum tube with the fuselage before glue. 20 X Aileron extension cord Aileron pushrod 1.2mm O Alenk-Gestange X Trial fit the control horn into the slot. CA If the parts will join, but with a gaps, sand or trim the parts a little at a time until the parts meet exactly with no gaps. Plastic control horn .....................2 Cut here for standard servo L/R Linkage Stopper set ..................
PAGE 13
22 23 TOP 2.mm drill bit Aluminum tube inside A Note: The hole on the surface of the top of the wing are pre-drilledat factory. Secure the wing in place using 3x15mm screw. WRONG 3x15mm screw B RIGHT B A 3x15mm screw .........
PAGE 14
25 IN CASE OF FLOATING USING Rear landing gear mount Note: The rear landing gear mount is pre-installed at factory X Rear landing gear not included 220mm BOTTOM - VIEW / Unteransicht 26 3x15mm screw .........6 CA Cut away only the covering .........
PAGE 15
27 0.5mm dia. Cable ...1 roll 2mm metal tube .....................
PAGE 16
29 Aileron 10mm 10mm Querruderausschlag Rudder Seitenruderausschlag 20mm 20mm Elevator Hohenruderausschlag 10mm 10mm 65 ~ 70mm Do not try to fly an out-of balance model! Uberprufen Sie vor dem Flug den Schwerpunkt. IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner to clean on surface of your model to keep the colour not fade. WARNING ! Do not put in a large-than recommended engine.