Instructions for use

ManualsBrandsPichler ManualsHobbySuper Cub BIG (Burda Squadron) 2710mm

Table Of Contents

PIPER PA-18

Radio control model

R/C Flugmodell

MONTAGEANLEITUNG

INSTRUCTION MANUAL

SPECIFICATIONS

Wingspan 106.6in.

Length 67.7 in.

Electric Motor (See next page)

Glow Engine 26-30cc two stroke

Radio 6 Channel / 8 Servos

WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.

Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann

hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um

professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist

durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

TECHNISCHE DATEN

Spannweite 2710mm

Lange 1720mm

Elektroantrieb (siehe nächste Seite)

Verbrennerantrieb 26-30cc 2-T

Fernsteuerung 6 Kanal / 8 Servos

ARF BY

SUPER CUB

Summary of content (16 pages)

PAGE 1
Radio control model R/C Flugmodell INSTRUCTION MANUAL MONTAGEANLEITUNG PIPER PA-18 SUPER CUB ARF BY TECHNISCHE DATEN SPECIFICATIONS Spannweite Lange Elektroantrieb Verbrennerantrieb Fernsteuerung Wingspan Length Electric Motor Glow Engine Radio 2710mm 1720mm (siehe nächste Seite) 26-30cc 2-T 6 Kanal / 8 Servos 106.6in. 67.7 in. (See next page) 26-30cc two stroke 6 Channel / 8 Servos WARNING! This radio controlled model is NOT a toy.
PAGE 2
REQUIRED FOR OPERATION (Purchase separately) BENOTIGTE KOMPONENTEN FUR DEN ABFLUG (Nicht enthalten) Extension for aileron servo, Flap servo. Gas Engine: 26 ~ 30cc Minimum 6 channel radio for airplane with 8 servos .Motor control x1 .Aileron x2 .Elevator x2 .Rudder x1 .
PAGE 3
HORIZONTAL STABILIZER - VERTICAL STABILIZER 1 TOP VIEW / Draufsicht Full the elevator out of the horizontal stabilizer. Cut two slots (only the covering) on the top and along the trailing edge of the horizontal stabilizer. HORIZONTAL STABILIZER TOP VIEW / Draufsicht 35mm 35mm 19mm 2 19mm Cut away only the covering on the top and bottom Cut away only the covering both side 3 4 Trial fit the horizontal stabilizer in place . Check the alignment of the horizontal stabilizer.
PAGE 4
Cut away only the covering on the top and bottom Pull the horizontal stabilizer through the other side of the fuselage and repeat the previous procedures to glue the second torque rod wire into the horizontal stabilizer. Realign the horizontal stabilizer, then glue the horizontal stabilizer into the fuselage, using a generous amount of thin CA. Apply thin CA to each of the four joints and use a generous amount to ensure to strong bond. 6 Thin CA CA glue Remove the horizontal stabilizer from the fuselage.
PAGE 5
Trial fit the vertical stabilizer in place . Check the alignment of the vertical stabilizer. When you are satisfied with the alignment, use a pencil to trace around the right and left of the stabilizer where it meets the fuselage. 12 Cut away only the covering on the left and right side. 11 Remove the vertical stabilizer from the fuselage. Using the sharp hobby knife, carefully cut away the covering inside the lines which were marked above. 5 min.
PAGE 6
MAIN LANDING GEAR BOTTOM - VIEW / Unteransicht 4X20mm screw .....6 Cut away only the covering * WARNING: When removing any covering from the airframe, please ensure that you secure the cut edge with CA or similar cement. This will ensure the covering remain tight. BOTTOM - VIEW / Unteransicht MAIN LANDING GEAR 3mm MAIN LANDING GEAR 3mm connector 3mm connector Connector ......
PAGE 7
MAIN LANDING GEAR 4X40mm screw ............2 4mm nut-washer BOTTOM - VIEW / Unteransicht 4mm nut 4mm nut 4x30mm screw 4x30mm screw 3mm connector Aluminum landing gear Hauptfahrwerk Aluminum landing gear Hauptfahrwerk FUSELAGE MAIN LANDING GEAR ...
PAGE 8
ENGINE Using a aluminum motor mounting plate as a template, mark the fire-wall where the four holes are to be drilled (1). Aluminum motor mounting plate Remove the aluminum motor mounting plate and drill a 5mm hole through the plywood at each of the four marks marked (2). Note: The aluminum motor mounting and screws included with the engine. 4 1 13/64” 5mm 5 2 B=152-158mm B 6 5X60mm screw 3 .........4 5mm washer ..................16 5mm nut ..................
PAGE 9
ELECTRIC MOTOR Using a aluminum motor mounting plate as a template, mark the fire-wall where the four holes are to be drilled (1). Remove the aluminum motor mounting plate and drill a 5mm hole through the plywood at each of the four marks marked (2). B=152-158mm Note: The aluminum motor mounting and screws included with the motor. B COWLING 4 - 6mm 2.mm 2.mm Relive the cowl to clear the silencer, carburetor and plug. 23x8mm screw ............
PAGE 10
FUEL TANK & LIPO. BATTERY Fuel tank flat (3mm plywood) Fuel tank seat bell 30cc Fuel tank Tipp X Fuel tank assembly Li-po battery Fuel tank seat bell Akku Kiettband aus dem PICHLER Sortiment Best.Nr.
PAGE 11
SERVO Servo tray IN CASE OF THE ELEVATOR SERVO IN SIDE OF THE FUSELAGE IN CASE OF THE ELEVATOR SERVO OUT SIDE OF THE FUSELAGE SERVO TRAY - TOP VIEW Servo tray Elevator servo FRONT Elevator pushrod FUEL TANK Rudder pushrod Throttle servo Throttle pushrod Rudder servo REAR FRONT
PAGE 12
Control horn ......................4 SERVO Flap servo 1.5mm Servo mount 2x30mm screw ...................8 Connector ...............4 2x10mm screw Flap servo hatch WING BOTTOM Aileron servo 2x10mm 1.5mm screw Servo mount Aileron servo hatch WING BOTTOM X Aileron, flap servo and light extension cord not include.
PAGE 13
WING BOTTOM - VIEW / Unteransicht CA Cut away only the covering CA L/R Assemble left and right wing halves the same way WING Aluminum tube Slide the aluminum tube into the fuselage as shown. L/R Do the same way with other wing halves.
PAGE 14
WING Secure the wing halves in place using 5x20mm screw. L/R Do the same way with other wing halves. 5x20mm .......2 5mm washer ..................2 WING CA FRONT Cut away only the covering LEFT BRACE (TOP VIEW) FRONT RIGHT BRACE (TOP VIEW) BOTTOM - VIEW / Unteransicht .........4 WING 3x12mm .........4 3x12mm .........2 3x12mm L/R Do the same way with other wing halves. 1.
PAGE 15
TAIL CA Stabilizer CA TAIL 0.7mm dia. Cable ...1 roll 2mm metal tube .....................4 TAIL ..............2 3x6.......2 2mm metal tube ..............
PAGE 16
LIGH 1mm CA 2x6mm ..........6 X DECOR BURDA VERSION AUSTRIA VERSION Note: Cut out the stickers and apply them in the proper area. Do not peel the backing paper off all at once. Peel off one corner of the backing and cut off with scissors. Arrange sticker on model and when satisfied adhere the corner without backing. Carefully peel back the rest of the backing while at the same time adhering the rest of the sticker.