Bedienungsanleitung BRUSHLESS REGLER S-CON Serie
Bedienungsanleitung S-CON Serie Brushless Regler Wir freuen uns, dass Sie sich für einen S-CON Brushless Regler aus unserem Sortiment entschieden haben. Sie besitzen damit einen Spitzenregler für bürstenlose Antriebsmotoren für Flugmodelle und Helis, bei dem besonderer Wert auf Zuverlässigkeit und sehr umfangreiche Programmiermöglichkeiten gelegt wurde.
Bedienungsanleitung • • • • • • • • • • • • 2. S-CON Serie Brushless Regler Der Regler ist ausschließlich für den Betrieb mit Akkus konzipiert. Betreiben Sie die Controller nie an einem Netzgerät. Überprüfen Sie den Controller regelmäßig auf Beschädigungen. Der Controller kann sich während des Betriebs erwärmen, sorgen Sie für eine optimale Abfuhr der entstehenden Wärme.
Bedienungsanleitung S-CON Serie Brushless Regler Darüber hinaus weisen die Regler der S-CON Serie folgende Features auf: • • Es besteht die Möglichkeit neue Firmware via PC zu installieren. Zur komfortablen Konfiguration kann optional eine Programmierbox erworben werden (# C6836). Die Regler zeichnen sich durch optimale Anpassungsfähigkeit an alle bürstenlosen Motortypen, einschließlich hochdrehender Innenläufer. Die Regler weisen einen sanften Anlauf auf und die Gaskurve eine hohe Linearität auf.
Bedienungsanleitung 4. S-CON Serie Brushless Regler Inbetriebnahme des Controllers 4.1 Anschluss des Reglers Die drei Motoranschlüsse eines S-CON Brushless Reglers können direkt mit den Motoranschlüssen verlötet oder über hochwertige Stecker mit dem Motor verbunden werden. Stellen Sie sicher, dass hochwertige Stecksysteme eingesetzt und / oder exakte Lötungen durchgeführt werden. Für den Akkuanschluss muss in jedem Fall eine Steckverbindung vorsehen werden.
Bedienungsanleitung • • • S-CON Serie Brushless Regler Stellen Sie zuerst die Anti-Blitz Verbindung her, verbinden Sie den Anti-Blitz Kontakt des Reglers mit dem zusätzlichen Akkuanschluss. Verbinden Sie dann die Hochstromanschlüsse mit dem Regler, Sie werden feststellen, dass dabei keine Funken entstehen. Lösen Sie die Anti-Blitz Verbindung bevor Sie weitere Schritte durchführen. Die folgende Abbildung zeigt schematisch den Anschluss mit Anti-Blitz Schaltung. 4.
Bedienungsanleitung 6. S-CON Serie Brushless Regler Programmierung des Reglers 6.1 Programmiermodus aktiveren / deaktivieren Um den Regler für eine Neu- oder Umprogrammierung vorzubereiten führen Sie bitte folgende Schritte durch: • Schalten Sie den Sender ein und bringen Sie den Gassteuerknüppel in die Vollgasposition (100 %). • Verbinden Sie den Antriebsakku mit dem Controller. • Warten Sie etwa 2 Sek. ab, bis vier Gruppen von jeweils zwei kurzen Tonfolgen (♪♪ ♪♪ ♪♪ ♪♪) erklingen.
Bedienungsanleitung S-CON Serie Brushless Regler Folgende Einstellungen stehen zur Verfügung: • Bremse aus • Weiche Bremswirkung • Mittlere Bremswirkung • Harte Bremswirkung Die jeweilige Einstellung wird durch eine differenzierte Tonfolge signalisiert, die der Tabelle auf der Seite 12 zu entnehmen ist. 2. Akkutyp einstellen (Menü 2) Die S-CON Brushless Regler können für alle Akkutypen im Flugmodellbereich konfiguriert werden.
Bedienungsanleitung • • • • • • • • • 5. Bremse: Akku Typ: Unterspannungsschwelle: Timingstufe: SBEC Spannung: Governor Modus: Motor Drehrichtung: Anlaufverhalten: Abschalt Modus: S-CON Serie Brushless Regler aus LiPo mit autom. Erkennung der Zellenzahl 3,0 V / 60 % automatisch 5,0 V abgeschaltet rechts herum mittlere Beschleunigung (30 %) Abregelung Timing einstellen (Menü 5) Das Timing kann dem jeweiligen Motortyp angepasst werden.
Bedienungsanleitung 7. S-CON Serie Brushless Regler Drehzahlregler Modus aktivieren Diese Option ist für den Einsatz bei Hubschraubern gedacht. Die Drehzahl wird, in Abhängigkeit von der jeweiligen Stellung des Gasknüppels konstant gehalten. Es stehen zwei verschiedene Einstellmöglichkeiten bereit. • RPM aus: Drehzahlregelung deaktiviert • Soft Start: Für den ersten ’Soft Start’ ist eine Verzögerung von 8 Sek.
Bedienungsanleitung 8. S-CON Serie Brushless Regler Drehrichtung des Motors umpolen Die Laufrichtung des Motors kann nicht nur durch das Vertauschen von zwei beliebigen Motor Anschlüssen umgepolt werden, der Vorgang kann auch Software mäßig vorgenommen werden. Es kann ein Vorwärts- oder Rückwärtslauf eingestellt werden. Die jeweilige Einstellung wird durch eine differenzierte Tonfolge signalisiert, die der Tabelle auf der Seite 12 zu entnehmen ist. 9.
S-CON Serie Brushless Regler Bedienungsanleitung Tabelle der veränderbaren Parameter und deren Einstellmöglichkeiten Tonfolgen Parameter Bremswirkung Akkutyp Unterspannung Werkseinstellung Timingstufen SBEC Spannung Governor Modus Motodrehrichtung Anlaufverhalten Unterpannungsabschaltung 1x lang (♫) 1x kurz (♪) 1x lang (♫) 2x kurz (♪ ♪) 1x lang (♫) 3x kurz (♪ ♪ ♪) 1x lang (♫) 4x kurz (♪ ♪ ♪ ♪) 4x kurz (♪ ♪ ♪ ♪) 1x lang (♫) mittel hart -- -- -- -- -- -- -- -- -- -- -- Schutz -- -- -
Bedienungsanleitung 7. S-CON Serie Brushless Regler Problemlösungen Trotz der integrierten Sicherheitseinrichtungen kann beim Betrieb eines S-CON Brushless Reglers evtl. einmal ein Problem auftreten. In der folgenden Tabelle sind die wichtigsten Probleme, deren Gründe, sowie Hinweise zur Lösung des Problems dargestellt. Bitte prüfen Sie alles genau, oft ist die Ursache für ein Problem in einer Fehlbedienung zu finden.
Bedienungsanleitung Problem Ursache Akku hat die eingestellte Unterspannungsgrenze erreicht Lösung Unverzüglich landen und voll aufgeladenen Akku einsetzen Mangelhafte bindungen Überprüfen Sie genau die Kabelverbindungen. Kabelver- Externe Störungen der Fernsteuerungsanlage Motor läuft ungewöhnlich an und überhitzt Fehlende Kühlluftzufuhr Servos ziehen einen zu hohen Strom, BEC überlastet Motor und / oder Luftschraube sind überdimensioniert 8.
Bedienungsanleitung S-CON Serie Brushless Regler Garantiezeit nicht. Wenn in der Garantiezeit Funktionsmängel, Fabrikations- oder Materialfehler auftreten, werden diese von uns kostenlos behoben. Weitere Ansprüche bei Folgeschäden, sind absolut ausgeschlossen. Zur Behebung von Garantiemängeln und zur Reparatur senden Sie den Regler an die auf der Rückseite der Anleitung angegebene Adresse.
Bedienungsanleitung S-CON Serie Brushless Regler Pichler Kunststofftechnik GmbH Lauterbachstr. 19 D-84307 Eggenfelden Tel: +49-(0)8721/9690-0 Fax: +49-(0)8721/7214 16 www.Pichler-modellbau.de E-mail: info@pichler.