Instructions for use

ManualsBrandsPichler ManualsHobbyPilatus Porter (Swiss Patrol) 2150mm

Semi scale model

BUILDING INSTRUCTIONS / MONTAGEANLEITUNG

SPECIFICATIONS

Wingspan 85.4 in.

Length 59.8 in.

Flying weight 14.4 lbs

Gas Engine 20cc

Radio 6 Channel / 8 servos

Technische Daten

Spannweite 2.170mm

Länge 1.520mm

Fluggewicht 4.500g

Verbrennerantrieb 20cc

Fernsteuerung 7 Kanal / 8 Servos

WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.

Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann

hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um

professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist

durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

20cc

Gas Engine

Pilatus

PC-6

Porter

RADIO CONTROL MODEL / RC FLUGMODELL

Glow 120 4T

1.5mm

L/R

Assemble left and right

sides the same way.

Drill holes using the stated

size of drill

(in this case 1.5 mm Ø)

Use epoxy glue

Take particular care here

Hatched-in areas:

remove covering

film carefully

Not included.

These parts must be

purchased separately

Check during assembly that these

parts move freely, without binding

Apply cyano glue

Low setting

SILICON

EPOXY A

EPOXY B

GLUE

Epoxy Glue (5 minute type)

Silicon sealer

Cyanoacrylate

Glue

Minimum 7 channel radio for airplane

with 5 standard servos and 3 mini servos

Nylon tube

Extension for aileron

servo, Flap servo.

REQUIRED FOR OPERATION (Purchase separately)

Epoxy Glue (30 minute type)

TOLLS REQUIRED

Hobby knife

Needle nose Pliers

Phillip screw driver

Awl

Scissors

Wire Cutters

(Purchase separately)

Hex Wrench

.........................................................

Sander

Masking tape - Straight Edged Ruler - Pen or pencil - Drill and Assorted Drill Bits

Read through the manual before you begin, so you will have an overall idea of what to do.

(Purchase separately)

CONVERSION TABLE

1.0mm = 3/64”

1.5mm = 1/16”

2.0mm = 5/64”

2.5mm = 3/32”

3.0mm = 1/8”

4.0mm = 5/32”

5.0mm = 13/64”

6.0mm = 15/64”

10mm = 13/32”

12mm = 15/32”

15mm = 19/32”

20mm = 51/64”

25mm = 1”

30mm = 1-3/16”

45mm = 1-51/64”

If exposed to direct sunlight and/or heat, wrinkels can appear. Storing the

model in a cool place will let the wrinkles disappear. Otherwise, remove

wrinkles in covering film with a hair dryer, starting with

low temperature. You can fix the corners by using a hot iron.

Bei Sonneneinstrahlung und/oder Wärme kann die Folie erschlaffen bzw. Falten

entstehen. Verwenden Sie ein Warumluftgebläse (Haartrockner) um evtl. Falten aus der Folie

zu bekommen. Die Kanten können Sie mit einem Bügeleisen behandeln. Nicht zuviel Hitze anwenden !

BENOTIGTE KOMPONENTEN FUR DEN ABFLUG (Nicht enthalten)

Klebstoff

Epoxy-Klebstoff (30min-Typ)

Epoxy-Klebstoff (5min-Typ)

Gas Engine: 20cc

Flapx2 standard servo - Aileronx2 standard servo

Rudderx1 standard servo - Elevatorx2 mini servo

Motorx1 mini servo

Glow 120 4T Engine

900 - 1.000Watts

Brushless Motor

Horizontal stabilizer

Apply a thin layer of machine oil or petroleum jelly to only the top and bottom of the trailing edge

of the elevator, then push the rudder and its hinges into the hinge slots in the trailing edge of the

vertical stabilizer.

When satisfied with the and alignment, hinge the rudder to the vertical stabilizer using CA glue (7D).

Hinge

Petroleum jelly

STABILIZER

Thin CA glue

Cut 2.3” (60mm) long slots along the hinge line in the

leading edge of the rudder.

Using a pencil, mark the rudder where the rudder torque

rod meet the rudder.

Drill a 3/32”(2.5mm) diameter hole in tail wheel gear mounting

slot, marking sure that you drill the hole perpendicular to the

leading edge of the rudder (7C).

2.5mm

7- Horizontal Stabilizer

Hohenleitwerk

30x4mm nylon bolt

............3

10- Engine - Cowl / Motor - Motorhaube

3x12mm screw

...........5

! Align the center mark on the engine

with the mark on the fire-wall.

Using a pencil or felt tipped pen, mark the fire wall

where the four holes are to be drilled (10A).

10A

Remove the engine mount and drill a 13/64”(5mm) hole

through the fire-wall at each of the four marks marked (10B).

10B

5mm

10C

Reposition the engine on to the fire-wall so

the distance from the prop hub to the fire-wall is

4.8 - 4.9”(123 - 125mm) (10C).

123 - 125mm

10D

10E

2mm

11- Glow Engine

! Align the mark on both

mounts with the mark on

the fuselage

Remove the engine mount and drill a 5mm hole through the fire-wall at each of the four marks marked.

Attach the four blind-nut to the fire-wall as show.

Using a pencil or felt tipped pen, mark the fire wall where the four holes are to be drilled

FRONT-VIEW

123 - 125mm

4x25mm...............4

3x20mm...............4

75 ~ 80mm

30mm

15mm

Aileron

Rudder

18- Balance / Schwerpunkt

15mm

30mm

Querruderausschlag

Seitenruderausschlag

Do not try to fly an out-of balance model!

Uberprufen Sie vor dem Flug den Schwerpunkt.

15mm

Elevator

Hohenruderausschlag

Flap

20mm

All details are subject to change

without notice !

Technische Anderungen und Irrtumer

vorbehalten !

IMPORTANT:

Please do not clean your model with pure alcohol,

only use liquid soap with water or use glass cleaner

to clean on surface of your model to keep the colour

not fade.

17- Decor / Aufkleber

Sticker

Aluminum tube

14- Installing the wing / Tragflacheneinbau

Wooden dowel

L/R

14A

14B

14C

16- Installing the wing / Tragflacheneinbau

The holes on the bottom

of the wings and side of

the fuselage are pre-drilled

at factory

Wing brace ( right - left)

To the bottom of the wing

To the side of the fuselage

L/R

3x15mm screw / Schraube

............................2

Wing

3x15mm

sscrew

3x15mm

sscrew

The blind-nut on the

bottom of the wing

installed at factory

Wing brace

............................2

TOP VIEW / Draufsicht

When you are satisfied with the alignment,

use a pencil to trace around the left and

right of the stabilizer where it meets the

fuselage(6B)

Cut away only

the covering

both side

Cut 7/8” (22mm) long slots along the hinge line in the

trailing edge of the vertical stabilizer for the rudder

torque rod bearings. Position of the slot on the side of

the vertical stabilizer, 2”(50mm) from the bottom (6A)

Test-fit the rudder torque rods into the slot.

NOTE: You may need to open up the slots so that

the torque rod bearing are not too difficult to push

* WARNING: When removing any covering from the airframe,

please ensure that you secure the cut edge with CA or similar

cement. This will ensure the covering remain tight.

! Securely glue together If coming off during

fly, you lose control of your air plane.

Remove the vertical stabilizer from the fuselage.

Using the sharp hobby knife, carefully cut away the

covering inside the lines which were marked above(6C)

6- Vertical Stabilizer

Seitenleiwerk

FUSELAGE

REAR VIEW

FUSELAGE

REAR VIEW

3x15mm screw / Schraube

...........................................2

Spring...............................................2

Main landing gear (5mm).................2

Landing gear (5mm).........................1

2- Landing gear / Fahrwerk

Aluminum tube

Hauptfahrwerk

Fahrwerksdraht

Two holes on the left and the right side of the fuselage are pre-drilled at factory

5mm Main landing gear

5mm landing

gear

Aluminum tube

Stopper (metal)

5.5mm Collar

Collar

Stellring

3x12mm screw

...................8

Nylon strap

............4

Stopper (metal)

...........2

..............4

3mm set screw

Kunststoffstreifen

1- Landing gear / Fahrwerk

5.5mm Collar

...........4

5mm gear (rear)

5mm landing gear

(front)

5mm landing gear

(rear)

L/R

BOTTOM - VIEW / Unteransicht

Caution: All holes on the bottom of the

fuselage are pre-drilled at factory

All blindnuts are

installed at factory

3x12mm screw

3- Tail gear / Heckspornrad

BOTTOM - VIEW / Unteransicht

3mm collar

3x12mm screw......4

Tail gear mount...1

12- Brushless Motor

5x70mm.......4

4mm.......x12

FRONT-VIEW

5mm

! Align with the marks

Plywood motor mounting plate

Sperrholztrager Platten

Vorderansicht

An den Markierungen ausrichten

3mm

1/8”

Aluminum motor

mounting plate

! Align with the marks

An den Markierungen ausrichten

Montagekreuz aus

Alu (nicht enthalten)

- Using a plywood motor mounting plate as a template, mark the fire wall

where the four holes are to be drilled (12A).

- Using a aluminum motor mounting plate as a template, mark the

plywood motor mounting plate where the four holes are to be drilled (12C).

- Remove the aluminum motor mounting plate and drill a 1/8”(3mm) hole

through the plywood at each of the four marks marked (12D).

- Remove the plywood motor mounting plate and drill a 13/64”(5mm) hole

through the fire-wall at each of the four marks marked (12B).

Firewall

123~125mm

B’

B=B’

A=A’

A’

TOP-VIEW / Draufsicht

SIDE-VIEW / Seitenansicht

Motorspant

Note the side thrust for motor!

Sturz und Zug beachten!

12A

12B

12C

12D

12E

12F

12G

12H

12I

Control horn

......................2

2x30mm screw

................4

2mm

8- Horizontal Stabilizer

Hohenleitwerk

9- Servo

BOTTOM - VIEW

Unteransicht

Put the Li-Po battery

in place.

Magnetic battery hatch.

Full the magnetic battery

hatch out of the fuselage.

13- Fuel tank / Tankeinbau

13A

13B

Put the fuel tank

in place.

13C

13D

Control horn

...................2

2x30mm screw

..........4

......2

Aileron servo

extension

cord

Aileron control horn

15- Servo

15A

15B

BOTTOM - VIEW

Unteransicht

Tail gear control horn B

4- Tail gear / Heckspornrad

5- Tail gear / Heckspornrad

Tail gear push rod

Note: Slide the tail gear

push rod in to he hole of

the tail gear control horn

B first.

3x12mm screw

...........4

Tail gear control arm

...2

Hatch (plywood)

........2

BOTTOM - VIEW / Unteransicht

BOTTOM - VIEW

Unteransicht

Connector

Tail wheel push rod

5C5D

..........1

Rudder arm

Rudder push rod

Rudder servo