User manual Douglas DC-3 (Dakota) - 1800mm

ManualsBrandsPichler ManualsARF aircraftDouglas DC-3 (Dakota) / 1800mm

Table Of Contents

Wingspan:.........................1800mm (70.8in.)

Length:..............................1200mm (47.2in.)

Electric Motor:.....................x2

Equipment Used).

Radio:....................6 Channel / 4..8 Servos

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.

Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um

professionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist

durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

Radio control model / Flugmodell

Instruction manual / Montageanleitung

Spannweite:...................................1800mm

Lange:............................................1200mm

Elektroantrieb.............(siehe nächste Seite)

Brushless Motor:.............x 2

Fluggewicht:.......................................3.2Kg

Fernsteuerung................6 Kanal / 4..8 Servos

Summary of content (19 pages)

PAGE 1
Radio control model / Flugmodell Instruction manual / Montageanleitung Wingspan:.........................1800mm (70.8in.) Length:..............................1200mm (47.2in.) Electric Motor:.....................x2 Equipment Used). Radio:....................6 Channel / 4..8 Servos Spannweite:...................................1800mm Lange:............................................1200mm Elektroantrieb.............(siehe nächste Seite) Brushless Motor:.............x 2 Fluggewicht:........................
PAGE 2
Sonderzubehör (empfohlen) / Optional Accessories (recommended): # C8802 Fernsteuerung GigaProp 6 Radio Set GigaProp 6 #C9218 Elektrisches Einziehfahrwerk Electric Retracts Alle Infos zu diesem Zubehör unter: More infos about these Accessories: www.pichler-modellbau.de X3598-120 Klebestoffe (nicht mitgeliefert) (Purchase separately) 5-Min Epoxy Cyanoacrylate Glue (thin type) Hex Wrench Phillip screw driver Hobby knife Awl Needle nose Pliers Scissors Wire Cutters Sander ...........................
PAGE 3
1- CENTER WING:ELECTRIC RETRACT INSTALLATION (OPTION) Tragflächenmittelstück CENTER WING - BOTTOM VIEW Ansicht von unten Cut away the leading edge as show. Note: Cut away the leading edge in case of the electric retract use only. Cut away the leading edge as show.
PAGE 4
2- CENTER WING: ELECTRIC RETRACT INSTALLATION (OPTION) Tragflächenmittelstück CENTER WING - BOTTOM VIEW Ansicht von unten Step 2A Note: Connect the electric retract to the receiver, with the retract switch on your radio in ON position, the electric retract will be in extended position. (Option) #C9218 Step 2B 3x12mm 2mm 3x12mm Secure the electric retracts in place using the eight 3x12mm screws. 2mm 3x12mm screw .........
PAGE 5
3- CENTER WING: ELECTRIC RETRACT INSTALLATION (OPTION) Tragflächenmittelstück 3x12mm screw ......4 3mm collar CENTER WING - BOTTOM VIEW Ansicht von unten .........2 .........2 Step 3A 2mm 2mm Fahrwerksabstützung Landing gear brace STEP 3B: FIXED GEAR INSTALLATION Note: In case of fixed gear using, do not cut the leading edge 3x12mm 2mm Fahrwerksträger Landing gear mount 1-Position the landing gear mount (plywood) onto the hard wood mounts as shown.
PAGE 6
4- CENTER WING Plastic control horn Tragflächenmittelstück .....................1 Ansicht von unten Step 4A 3x12mm screw 3x12mm screw ......4 2mm Bend the steel wire for the adjusting. 2mm Adjuster screw Fahrwerksabstützung Step 4B 2x8mm Korrekt ausrichten Ensuring that they are accurately aligned. 2X8mm screw ......
PAGE 7
5- CENTER WING Ansicht von oben Step 5A Ansicht von oben Step 5B Motorträger Seitenansicht -Using a aluminum motor mounting as a template, mark the firewall where the four holes are to be drilled. -Remove the motor and drill a 1/8”(3mm) hole through the plywood at each of the four marks marked .
PAGE 8
6- CENTER WING Tragflächenmittelstück Ansicht von oben Step 6A Step 6B
PAGE 9
7- CENTER WING Tragflächenmittelstück 2x8mm Ansicht von unten Step 7A 1.5mm 2x8mm 2X8mm screw ......6 1.
PAGE 10
8- CENTER WING 2x8mm Ansicht von oben Step 8A 2x8mm 1.5mm 2x8mm 1.5mm 2x8mm 1.5mm 1.5mm 2X8mm screw ......14 9- RIGHT (LEFT) WING Step 9A Plastic control horn .....................2 Die Löcher für die Ruderhörner und Servos sind werksseitig vorgesehen und können unter der Folie ertastet werden.
PAGE 11
10- RIGHT (LEFT) WING Rechte und linke Flächenhälfte Rechte Flächenhälfte von oben Step 10A Connector ...2 2 mm 1.2x175mm rod ....
PAGE 12
- JOINING THE WING Flächenteile langsam und spaltfrei zusammenschieben
PAGE 13
- JOINING THE WING Do the same way with the right wing. 3x15mm screw .........2 Aluminum tube inside 2.mm drill bit Secure the wing in place using 3x15mm screw.
PAGE 14
- HORIZONTAL STABILIZER Bitte korrekt ausrichten Trial fit the horizontal stabilizer in place on the fuselage. Check the alignment of the horizontal stabilizer by measuring from a fixed point along the center line of the fuselage to the leading edge on each side of the horizontal stabilizer. The distance must be equal on both sides.
PAGE 15
- HORIZONTAL STABILIZER AND TAIL WHEEL Remove the horizontal stabilizer from the fuselage. Using a straight edge and a sharp hobby knife, carefully cut away the covering inside the lines which were marked. Be cautious not to cut into the wood - this will weaken the structure. 1 1- Insert the tail wheel pushrod into the hole on the tail gear control horn (as show). 2- Install the tail wheel control horn in place. 3- Instal the tail wheel gear in place.
PAGE 16
- TAIL WHEEL COVER 1.5mm 2x8mm 2x8mm 17- VERTICAL STABILIZER Cut away only the covering Remove the horizontal stabilizer from the fuselage. Using a straight edge and a sharp hobby knife, carefully cut away the covering inside the lines which were marked. Be cautious not to cut into the wood - this will weaken the structure.
PAGE 17
18- VERTICAL STABILIZER continued Slide the rudder push-rod through the plastic cover and the plastic push-rod tube into the fuselage.
PAGE 18
19- LINKAGES Belt Tail wheel push-rod Rudder push-rod Left elevator push-rod Right elevator push-rod
PAGE 19
20- BALANCE AND CONTROL SURFACE Schwerpunkt und Ruderausschläge (100 ~ 110mm) Wing center section Höhenruder 15mm 12mm 15mm 12mm Querruder 20mm 20mm Seitenruder 20-25mm Landeklappen