Instructions for use

ManualsBrandsPichler ManualsElectric gliderMotorspatz V2 (white/red) 2500mm

Table Of Contents

Wing span approx : 99.2 in.

Length approx : 44.0 in.

Radio: 4Channel / 4 servos

INSTRUCTION MANUAL / MONTAGEANLEITUNG

SPECIFICATION

TECHNISCHE DATEN

Spannweite : 2520mm

Lange : 1120mm

Fernsteuerung: 4 Kanal / 4 servo

Electric Powered Glider

R/C Motorsegler

ARF BY

WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.

Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann

hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um

professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist

durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

Summary of content (8 pages)

PAGE 1
Electric Powered Glider R/C Motorsegler INSTRUCTION MANUAL / MONTAGEANLEITUNG SPECIFICATION Wing span approx : 99.2 in. Length approx : 44.0 in. Radio: 4Channel / 4 servos TECHNISCHE DATEN Spannweite : 2520mm Lange : 1120mm Fernsteuerung: 4 Kanal / 4 servo ARF BY WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
PAGE 2
REQUIRED FOR OPERATION (Purchase separately) BENOTIGTE KOMPONENTEN (Nicht im Lieferumfang enthalten) ECO Adapter 5.0mm Best.Nr. C6062 Klappluftschraube 13x8 Best.Nr C7127 Minimum 4 channel radio for airplane Minimum 4 Kanal Mini servo DS3012 Fernsteuerung # C49955 Regler: PULSAR A-50 # C6130 PULSAR 40 # C6217 Battery / Flugakku # C2141 LEMONRC 3700-11.
PAGE 3
1 4x30mm nylon bolt ............1 TOP VIEW Draufsicht Control horn ...........1 1A 1B 1D 1C MARK Trial fit the elevator half in place, check the alignment of the horizontal stabilizer and the elevator half. Using a pencil, mark on the leading edge of elevator, where the hole is to be drilled. 1E 1F Drill a 1.5mm hole of the mark made in Step 1D Marking sure that you drill the hole perpendicular to the leading edge of the elevator half. CA 1.5mm Securely glue together.
PAGE 4
2 BOTTOM - VIEW Unteransicht 2B White nylon push-rod guider 2A Cut away only the covering 2A Slide the elevator push-rod (in the hard-ware bag) into the white nylon push-rod guider. 2B Insert the Z bend into the control horn. 2C Push the foot of control horn into the slot on the elevator as shown. 2C 2D Secure the control horn in place using thin CA glue. CA Thin CA 2D Securely glue together. If coming off during flight, you lose control of your air plane.
PAGE 5
3 3A Control horn ...........1 CA Slide the rudder push-rod (in the hard-ware bag)into the white nylon push-rod guider. 3D 3B Insert the Z bend into the control horn. Thin CA 3C Push the foot of control horn into the slot on the rudder as shown. CA 3D 3C 3A 3B CA Cut away the covering 4 4x50mm screw ........1 ........2 ........2 ........1 BOTTOM - VIEW Unteransicht 4mm nut 4mm washer 4x40mm screw X 4mm washer 4x50mm screw 5 1.2x900mm rod.............
PAGE 6
Linkage Stopper set Gestängeanschluss ..............2 BOTTOM - VIEW Unteransicht Control horn...2 Aileron servo hatch (ply 3mm) Aileron servo hatch (ply 3mm) Cut away the covering CA Thin CA Fuhren Sie die Verklebungen mit gro ter Sorgfalt aus. 7 2.5x10mm screw ............
PAGE 7
8 TOP VIEW Draufsicht Aluminum wing joiner 4X20mm A B A B L/R 5 min. Epoxy 20x6mm woden dowel. TOP VIEW Draufsicht 4x20mm screw .....2 6x20mm wooden dowel .....4 WING HALVES INSTALLATION 1- Pull the magnetic top hatch out of the fuselage. 2- Carefully slide the wing halve to the fuselage as shown (Right picture), ensuring that the wing halve accurately aligned. 3- Carefully slide the second wing halve to the fuselage. Firmly press the two halves together.
PAGE 8
9 Do not try to fly an out-of balance model! Uberprufen Sie vor dem Flug den Schwerpunkt. Note: If necessary, move the battery pack or add weight to either the tail or nose until the correct balance is achieved. 68 ~ 72mm CG WARNING ! Securely install the receiver and power pack, ensuring they will not come loose or rattle during flight. Never fly before checking the Cg’s required position.