PICHLER Joker XL Anleitung / Manual R/C Elektromodell / Electric Powered Model (Alle Versionen / All Versions) Vorbereitet für den Einbau eines Elektroantriebs und einer Schleppkupplung für den Seglerschlepp. Factory-prepared for use of electric motor and convinient glider towing system. 95% vormontiert ARF Vorbereitet für Landeklappen. Factory-prepared for Flaps.
JOKER XL Instruction Manual Dieses ferngesteuerte R/C Flugmodell ist für Anfänger nicht geeignet sondern richtet sich an fortgeschrittene Modellbauer. Trotz sehr hoher Vorfertigung erfordern die Endmontage und der Betrieb des Modells etwas Übung sowie grundlegende Erfahrungen. Wenn Sie unerfahren sind, bitten Sie einen Modellbaukollegen um Hilfe oder fragen Ihren Modellbau-Fachhändler vor Ort. Bevor Sie mit dem Zusammenbau beginnen, prüfen Sie den Inhalt auf Vollständigkeit, Passgenauigkeit bzw.
JOKER XL Anleitung / Manual Sonderzubehör für Joker XL / Accessories for Joker XL Nachstehendes Zubehör wurde von uns ausgiebig erprobt und wird für beste Flugeigenschaften empfohlen. Weitere Informationen und Bestellmöglichkeit unter www.pichler-modellbau.de These accessories have been extensively tested and are recommended for best flying performance. For more information please visit www.pichler-modellbau.
JOKER XL Instruction Manual SAFETY PRECAUTION. + This is not a toy + Be sure that no other flyers are using your radio frequency. + Wear safety glasses. + Keep loose clothing and wires away from the propeller. + Do not start the motor if people are near. Do not stand in line with the side of the propeller. + Make motor adjustments from behind the propeller only. Do not reach around the spinning propeller. D. C. B. A. A. E. A. Wing panel. E. Vertical stabilizer B. Fuselage. E.
JOKER XL Instruction Manual C/A glue AILERON SERVOS. 1.INSTALLING THE AILERON SERVOS. C/A glue 1) Install the rubber grommets and brass eyelets onto the aileron servos. C/A glue Attention: You can use either 1 or 2 aileron servos per wing panel. Achtung: Sie können entweder 1 oder 2 Querruderservos pro Tragflächenhälfte verwenden. C/A glue Flap. Aileron.
JOKER XL Instruction Manual 5. Instal servo tray with aileron servo into the wing as same as picture below. C/A glue C/A glue Secure. 2) Using a modeling knife, remove the covering at possition show below. 2.INSTALLING THE AILERON CONTROL HORN. Aileron control horn 3) Using the thread as a guide and using masking tape, tape the servo lead to the end of the thread: carefully pull the thread out. When you have pulled the servo lead out, remove the masking tape and the servo lead from the thread.
JOKER XL Instruction Manual FLAP SERVOS. 1.INSTALLING THE FLAP SERVOS. thread Electric wire. Aileron control horn. 3.INSTALLING THE AILERON LINKAGES. Installing the air brake linkages as pictures below. M3 lock nut. M3 Secure. 115 mm. Repeat the procedure for the other wing half. 2.INSTALLING THE FLAP CONTROL HORN. Flap control horn. Secure. 6 Repeat the procedure for the other wing half.
JOKER XL Instruction Manual Mark line. 408 mm Flap Control horn. Flap. Straight line. 3.INSTALLING THE FLAP LINKAGES. Installing the air brake linkages as pictures below. M3 lock nut. M3 115 mm. Flap. cut. hier trennen Wenn Sie Landeklappen nutzen möchten trennen Sie bitte hier das Querruder mit einer feinen Säge. If you want to use flaps, cut the aileron as shown above. Bottom side. Flap.
JOKER XL Instruction Manual INSTALLING ELECTRIC MOTOR. See picture below: INSTALLING THE SPINNER. Install the spinner backplate, propeller and spinner cone. The spinner cone is held in place using two 3mm x 15mm wood screws. Front view. 3 x15mm 3x 15mm Secure. Secure. Secure.
JOKER XL Instruction Manual INSTALLING THE BATTERY. See picture below: SERVO INSTALLATION.
JOKER XL Instruction Manual A+B Epoxy PLUS glue 3 x 15mm 10
JOKER XL Instruction Manual INSTALLING THE MAIN LANDING GEAR. Secure. PARTS REQUIRED 4x15mm 5 x35mm 1. The blind nuts are already mounted inside the fuselage. M3 lock nut . M3 2. The holes in the landing gear should be to accept the mounting bolts. 55mm Landing gear. 3. Using the hardware provided, mount the main landing gear to the fuselage. 4x15mm Secure.
JOKER XL Bottom side. Instruction Manual 5. A drop of C/A glue on the wheel collar screws will help keep them from coming lose during operation. Repeat the process for the other wheel. Secure. 4. Assemble and mounting the wheel pants as shown in the following pictures. 5x 35mm Bottom side. ELEVATOR INSTALLATION. SERVO INSTALLATION. 1. Install the rubber grommets and brass collets into the elevator servo. Test fit the servo into the servo tray. 2.
JOKER XL Instruction Manual Right side. C/A glue C/A glue Secure. C/A glue elevator servo right side HORIZONTAL STABILIZER INSTALLATION Horizontal stabilize installation . C/A glue See picture below. Bottom side.
JOKER XL Instruction Manual Bottom side C/A glue C/A glue Bottom side 3x 15mm Top side. Secure. Bottom side. Check to mark sure the wing and stabilizer are paralell. If they are not, lightly sand the opening in the fuselage for the stabilizer until the stabilizer is paralell to the wing. 14 Top side.
JOKER XL Instruction Manual ELEVATOR CONTROL HORN INSTALLATION. Top side. Elevator control horn install as same as the way of aileron control horn. Please see pictures below. Elevator control horn. ELEVATOR PUSHROD INSTALLATION. Elevator pushrod install as same as the way of aileron pushrod. M3 lock nut. M3 160 mm. A+B Epoxy PLUS glue Elevator pushrod Top side. Elevator pushrod Elevator control horn.
JOKER XL Instruction Manual MOUNTING THE TAIL WHEEL BRACKET. 3x 12mm 1) Set the tail wheel assembly in place on the plywood plate. The pivot point of the tail wheel wire should be even with the rudder hinge line and the tail wheel bracket should be centered on the plywood plate. 3 x 12mm Secure. Bottom side. Push in to. RUDDER SERVO INSTALLATION. Rudder servo install as same as method of elevator servo. See picture below: Rudder servo. Left side Secure. Mark point.
JOKER XL Instruction Manual Rudder servo left side VERTICAL INSTALLATION. Vertical stabilizer installation See picture below. 2.Mark the shape of the vertical on the left and right side on the rudder using a felt-tip pen. Mark line. 1. Slide the rudder into the fuselage as same as picture below. Top side. 3.Now, remove the rudder and using a modeling knife, carefully cut just inside the marked lines and remove the film of the rudder.
Instruction Manual Push . JOKER XL Epoxy glue. Horizontal Stabilizer. 90º Vertical Stabilizer. 4. Put the vertical stabilizer back in place. Using a triangle, check to ensure that the vertical stabilizer is aligned 90 degree to the horizontal stabilizer. Epoxy glue. 18 C/A glue.
JOKER XL Instruction Manual C/A glue. Mark point. C/A glue. Carefully make a 90 degree bend down at the mark made. Cut off the excess wire, leaving about 20mm beyond the bend. Bend and cut. A+B Epoxy PLUS glue Be nd 90 de gr ee . Push. 20mm.
JOKER XL Instruction Manual 5) When you are sure that everything is a aligned correctly, mix up a generous amount of 30 minute epoxy. Apply a thin layer to the slot in the mounting platform and to the vertical stabilizer mounting area. Apply epoxy to the lower rudder hinge. Set the stabilizer in place and re-align. Double check all of your measurements once more before the epoxy cures.
JOKER XL Instruction Manual RUDDER PUSHROD INSTALLATION. Rudder pushrod install as same as the way of aileron pushrod. Do not permanently secure the receiver and battery until after balancing the model. 4. Using a 2mm drill bit, drill a hole through the side of the fuselage, near the receiver, for the antenna to exit. M3 lock nut. M3 160 mm. Receiver Rudder pushrod Receiver Top side. Rudder pushrod WING ATTACHMENT. Elevator pushrod Locate the aluminium wing dihedral brace. aluminium 19mm 520 mm.
JOKER XL Instruction Manual Left wing. Right wing. secure. 6x 45 mm wing bolt Secure.
JOKER XL Instruction Manual BALANCING. CG: 1) It is critical that your airplane be balanced correctly. Improper balance will cause your plane to lose control and crash. 110mm THE CENTER OF GRAVITY IS LOCATED MM BACK FROM THE LEADING EDGE OF THE WING. Schwerpunkt 2) Mount the wing to the fuselage. Using a couple of pieces of masking tape, place them on the top side of the wingmm back from the leading edge, at the fuselage sides. 3. Turn the airplane upside down.
