® PicoScope Oscilloscope Diagnostics Tes t le ads • Current clamps • probes • hoses .....
-CHANNEL STARTER KIT 4-CHANNEL STARTER KIT 2-Ch £595 $982 ¤720 4-Ch £975 $1609 ¤1180 2-CHANNEL PicoScope 4225 2-channel scope with rubber case 1 x Small crocodile clip black & red, 2 x BNC to 4 mm test leads: blue and red, 1.
4-CHANNEL DIESEL KIT £1475 $2434 ¤1785 PicoScope 4425 4-channel scope with rubber case Oscilloscope probe for use with CAN, LIN and FlexRAY signals 2 x S Hook, 2 x Multimeter style test probe black & red, 2 x Small crocodile clip black & red, Back-pinning probes, 2 pin breakout lead, 2 x Shrouded to unshrouded 4mm adaptor black & red, 20A/ 60A DC current clamp, 2000A/200A Current clamp with BNC 4 x BNC to 4 mm test leads: blue, red, green, yellow, 1.
Fix it right first time Whether or not you have a fault code, swapping parts risks repeat customer visits or unnecessary expense. A PicoScope lets you see what’s really happening on the vehicle to eliminate guesswork. Whether it is drivability concerns, intermittent problems or just not an obvious fault, a PicoScope reveals the information a scan tool can’t, so you can find faults and fix them right first time. Our kits come with selected accessories to assist you with the job at hand.
60 A / 20 A CURRENT CLAMP The 60 A current clamp allows you to measure current up to 60 amps in a wire without cutting, disconnecting or stripping the wire. It plugs directly into the PicoScope, and is ideal for measuring current waveforms from fuel pumps, injectors and ignition coils. When the correct preset test is selected, PicoScope shows current readings in amps. BNC 60 A current clamp TA018 £99 $165.35 ¤119.
SECONDARY IGNITION PICKUP COIL-ON-PLUG (COP) PROBE EXTENSION LEADS The secondary ignition pickup enables the PicoScope to measure high-tension (HT) voltages in secondary ignition circuits. It clips onto the HT lead with no need to disconnect the lead. The lead includes a ground clip that you must always connect to battery negative (earth) to prevent stray voltages from damaging the PicoScope. These extension leads give access to the HT (secondary) ignition circuit in coil-on-plug engines.
Flexible Back-pinning probes SMALL CROCODILE CLIPS Like TA008 back-pinning probes, these probes are designed for back-probing under the insulation of multi-plug terminals. The TA161 and TA162 have a flexible section to improve access to difficult areas. Each probe fits onto the 4mm plug of our BNC to 4mm test leads. Note that, unlike the probes in the TA008, the probe tips are not replaceable. Flexible back-pinning Probe (black) TA161 £4 $6.60 ¤4.84 Flexible back-pinning Probe (red) TA162 £4 $6.60 ¤4.
Battery Clips MULTIMETER PROBES These plier-type clips are designed for connection to the vehicle battery terminals and fit all our BNC-to-4mm test leads. These probes fit all our BNC-to-4-mm test leads. They are used to make contact with exposed wires and terminals. Multimeter probe (black) TA001 £4 $6.60 ¤4.84 Multimeter probe (red) TA002 £4 $6.60 ¤4.84 SPRUNG HOOK PROBES These probes fit all our BNC-to-4-mm test leads. They allow you to make hands-free contact with exposed wires and terminals.
60 MHZ OSCILLOSCOPE PROBE 4 MM SHROUDED TO UNSHROUDED ADAPTORS This 60 MHz oscilloscope probe is used for accurately measuring fast signals like CAN bus and FlexRay. A two position slide switch allows attenuation of either x1 or x10 to be selected. Standard BNC plug 1.2m long. 60 MHz oscilloscope probe MI007 £15 $24.75 ¤18.15 DIFFERENTIAL PROBES Converts the shrouded 4-mm (banana) plug on our test leads to an unshrouded plug for use with the PP619 CAN Test Box or vehicle manufacturers’ breakout boxes.
FUSE EXTENSION LEADS 2-PIN BREAKOUT LEAD For regular blade (ATO/ATC) and mini blade (ATM) fuses. Use with the Pico current probes for fuse-based diagnosis (see tutorials on picoauto.com) and measurements. Fuse extension leads PP408 £35 $57.75 ¤42.35 For standard 2-pin sensors and actuators. With 4mm plugs to connect to PicoScope test leads. 2-pin breakout lead TA012 £25 $41.25 ¤30.
6-WAY UNIVERSAL BREAKOUT LEADS No need to pierce insulation or back-pin connectors. Fully shrouded and insulated for safety. These breakout leads simply connect into the existing cable loom and enable voltage readings to be taken from numerous sensors in the engine compartment. Micro 0.6mm TA063 £49 $80.85 ¤59.29 Small 1.5mm TA024 £49 $80.85 ¤59.29 Medium 2.3mm TA025 £49 $80.85 ¤59.29 Large 2.8mm TA026 £49 $80.85 ¤59.29 Breakout lead kit (S, M, L) PP327 £129 $212.85 ¤156.
WPS500X PRESSURE TRANSDUCER CAN TEST BOX The CAN Test Box allows you to connect your PicoScope oscilloscope to the 16 pin diagnostic connector enabling you to monitor any signals present, such as the CAN High and Low signals. The CAN Test Box terminal pin ports are accessible with standard 4 mm plugs. The CAN Test Box uses numbered backlit LEDs which illuminate when signal data is present on the corresponding pin of the Data Link Connector (subject to the vehicle manufacturer’s specification).
VACUUM HOSE EXHAUST ADAPTOR This hose allows you to connect to the intake manifold for vacuum testing. Insert this hose into the tailpipe to detect engine misfires. Vacuum hose TA085 £12 $19.80 ¤14.52 Exhaust adaptor TA087 £20 $33 ¤24.20 BLEED HOSE FUEL HOSES Fits on the PP652 WPS500X pressure transducer’s bleed port, allowing you to drain off fluid cleanly. Bleed hose TA086 £10 $16.50 ¤12.10 HIGH STRENGTH COMPRESSION HOSES Enables connection to fuel systems with WPS500X.
S-HOOK Use this S-hook to keep test leads tidy in the engine bay. CARRY CASE S-hook MI168 £2 $3.30 ¤2.42 TRAINING DVD The hard outer shell of these cases protects your kit from the inevitable knocks and bumps of workshop life. Designed to help you benefit from the extensive experience of Pico experts and users, troubleshooting problems in today’s vehicles. Kit carry case PA084 £75 $123.75 ¤90.75 PicoScope Training Resources DVD DI090 £80 $132 ¤96.
PicoDiagnostics NVH Kit • Includes accelerometer and microphone • Full screen, high–resolution results are presented clearly and accurately • No external memory required– saves directly to laptop or PC • Record up to 500 seconds of data • Automatic analysis • Detects multiple vehicle vibrations • Customer report function • Plugs into your automotive PicoScope (sold separately) The PicoDiagnostics NVH Kit is the cost–effective answer to the many NVH problems facing technicians today.
ABS Diesel injectors Petrol injectors Carbon canister solenoid AFM (hot wire) EGR valve Primary ignition amps MAP sensor (analog) Alternator ripple Idle speed control valve CAN bus Primary ignition volts Compression test Pico Technology James House Colmworth Business Park ST. NEOTS PE19 8YP United Kingdom +44 (0) 1480 396395 +44 (0) 1480 396296 sales@picotech.
