PICO MACOM PRR Series Optical Return Receiver PRR Owners Manual Please read this manual thoroughly before use. Keep this manual handy for future reference. Visit Our Web-Site www.picomacom.com Contact Us 858.546.5050 Toll Free 800.421.
Fiber Optic Series PICO MACOM Pico Macom PRR Optical Return Receiver OWNERS MANUAL This manual is intended for use by purchasers of Pico Macom PRR receiver(s) and their qualified technicians. This document is the property of Pico Macom, and embodies proprietary subject matter. All design, manufacture, reproduction, use and sale rights regarding the same are expressly reserved. This manual may not be reproduced without written consent from Pico Macom.
PICO MACOM Fiber Optic Series IMPORTANT SAFEGUARDS Pico Macom strongly advises you to read and understand the following safety instructions prior to installing and operating this equipment. • Read These Instructions First. All safety and operating instructions should be read before installing or operating this equipment. Safety and operating instructions should be retained for future reference. • Retain This Instruction Manual. Safety and operating instructions should be retained for future reference.
PICO MACOM Fiber Optic Series Laser Safety Information: The PRR Receivers are designed for use with fibers that have output power levels that are classified as Class 1M per IEC/EN 60825-1/A2:2001 and comply with FDA/CDRH, 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50 dated 26 July, 2001.
PICO MACOM Fiber Optic Series TABLE OF CONTENTS Chapter 1 Introduction.................................................................................................................. 6 1. Introducing the Pico Macom PRR Optical Return Receiver............................................. 6-7 Chapter 2 Specifications................................................................................................................ 8 1. RF Performance............................................................
Fiber Optic Series PICO MACOM Chapter 1 Introduction 1. Introducing the Pico Macom PRR Optical Return Receiver OPTICAL RETURN PATH RECEIVER RECEIVER 1 POWER RF ADJUST ON LINE RECEIVER 1 OPTICAL RF ADJUST ON LINE RECEIVER 1 OPTICAL RF ADJUST ON LINE RECEIVER 1 OPTICAL RF ADJUST ON LINE OPTICAL The Pico Macom PRR Optical Return Receiver is a 1 RU (1.75 high x 19 inches wide) rack mountable chassis with one, two, or four Optical Return Receivers included.
PICO MACOM Fiber Optic Series The PRR receiver includes an autoranging power supply and may be installed in 120 or 240 VAC systems by purchasing an appropriate power cord at the local PC computer shop if the supplied cord is not appropriate. (A NEMA-15P is supplied in North America.) When powered, the front panel POWER LED will be lighted and each receiver’s ONLINE LED will be lighted.
Fiber Optic Series PICO MACOM Chapter 2 Specifications 1. RF Performance SPECIFICATION LIMITS Frequency Range 5 to 200 MHz Connector F-connector, female Impedance 75 ohm Output Return Loss > 8 dB Output RF Level > 45 dBmV RF Output Control Range > 10 dB RF Frequency Response (Flatness) + 1.5 dB Carrier–to-Noise Ratio > 50 dBc* Composite Second Order (CSO) > 60 dBc* Composite Triple Beat (CTB) > 65 dBc* Rear Panel Test Port Level -20 dB from primary output, typ.
PICO MACOM Fiber Optic Series Chapter 3 Installation and Operation 1. Unpacking the Unit Please inspect the cartons on receipt and note damage to the carton and inspect for possible unit damage. If damage is found, please contact shipper immediately, before unpacking, to follow that shipper’s procedure for claims. Please open the carton and unpack carefully. Locate the power cord. Do not connect a unit to power if there is serious mechanical damage to prevent possibly unsafe conditions. 2.
Fiber Optic Series PICO MACOM OPTICAL RETURN PATH RECEIVER RECEIVER 1 POWER 4. RF ADJUST ON LINE RECEIVER 1 OPTICAL RF ADJUST ON LINE RECEIVER 1 OPTICAL RF ADJUST ON LINE RECEIVER 1 OPTICAL RF ADJUST ON LINE OPTICAL Making Rear Panel Connections 2 OPTICAL IN 1 OPTICAL IN ON/OFF RF RF RF RF 90-264 VAC 47-63 Hz PRR Rear Panel (PRR-4 Shown) 4.1 Power Connection and Initial Power Up Insert the supplied power cord into the IEC320 male power socket on the chassis.
Fiber Optic Series PICO MACOM Example of a fiber cable cleaner (source: Fiber Instrument Sales, www.fiberinstrumentsales.com). 4.3 RF Output Connections Connect a RF output coax cable to a rear panel F-connector labeled RF OUT and route to combiners, transmitters or other equipment which use the RF signal. Install a second coax for the PRR-2 and up to 4 for the PRR-4, if desired. You may monitor each output signal from the rear panel test port.
PICO MACOM 6. Fiber Optic Series Maintenance The PRR receiver contains no internal user adjustments or maintenance points. 6.1 Decreased Performance Due to Contamination The most likely cause of decreased RF signal quality is contamination in the OPTICAL IN connector. The optical jumper connectors may be contaminated by the slightest touch to human skin or other apparently clean surfaces.
PICO MACOM Fiber Optic Series Chapter 4 Customer Support Information 1. If You Need Help If you need assistance while working with the Pico Macom products call Pico Macom Field Support at 858-546-5050, or 800 421-6511 between 8 AM and 5 PM Pacific Time. Alternatively, you may contact us via email at sales@picomacom.com. 2. Repair Procedure Pico Macom has established a streamlined process to ensure the rapid return of products when repair is required.
PICO MACOM Fiber Optic Series Limited Warranty Pico Macom warrants to the original purchaser that all of its new products are of sound design, quality materials and workmanship at the time of manufacture and will be free from related defects for one year from the original purchase date. Pico Macom will repair or, at its discretion, replace without cost to the original purchaser, the product which, upon inspection by Pico Macom, appears to be defective or not conforming to factory specifications.
Fiber Optic Series PICO MACOM To qualify for the program, you must have current open-terms with us and in good standing. We must receive your failed unit within one week after the loaner unit is shipped to you, and must likewise receive the loaner unit within one week after the repaired unit is shipped back to you. Daily rental fees not to exceed 10% of the equipment’s List Price will apply beyond one week after the loaner or repaired unit are shipped to you.
PICO MACOM 6260 Sequence Drive San Diego California 92121 Phone: 858.546.5050 Sales: 858.546.5055 Fax: 858.546.5051 www.picomacom.com sales@picomacom.com Printed in the U.S.A.