PIEGA User Manual PIEGA PS 1 / PS 2 Active-Subwoofer
«Music. That‘s really the only important issue when it comes to loudspeakers...» In our view, the superior loudspeaker is the one that does not interfere. One that adds no sound of its own. That accurately and naturally conveys what was played in the concert or recording studio. Since 1986 we have been working to perfect this ideal – with a pioneering spirit, inventiveness and exacting craftsmanship. You will now be able to hear for yourself how far we have succeeded.
Contents This user manual describes how to connect the PIEGA active subwoofer to different loudspeaker con figurations and the appropriate setting options for optimum operation in stereo and home cinema mode. It also contains instructions for unpacking and setting up the subwoofer.
Precautions Please read this user manual carefully and pay special attention to the following precautions and warnings. In your own interest, we advise you to strictly observe the following procedure when installing your new PIEGA subwoofer. Safety Precautions / Warnings: The PIEGA subwoofers have been designed for use with PIEGA loudspeaker products. Nevertheless, the subwoofer can also be operated with the loud speakers of other suppliers.
Unpacking Special care was taken in the packaging of your subwoofer in order to ensure that this new PIEGA quality product reaches your living room safely and undamaged. In order to avoid any damage when unpacking the loudspeaker, follow closely the instructions below. Procedure: Before unpacking, remove any jewelry such as watches, rings, bracelets etc.
Positioning The subwoofer can be installed flexibly and easily. Due to its relatively small size, it can be integrated in any unit and can be positioned as required virtually anywhere in the room. However, to ensure the most natural sound, the subwoofer should be placed on the floor near the two front loudspeakers. Ideal setup For both surround and stereo mode, position the subwoofer as close to the two front loudspeakers as possible. The connecting terminal of the PS 1 / PS 2 should face the wall.
Terminal area Its large range of connection options offers the subwoofer a wide number of configurations both for stereo and for surround mode. Refer to the appropriate user manual supplied for specific information on the loudspeakers used and components of your stereo or surround system.
Setup Procedure This connection configuration for 5.1 surround applications uses an AV receiver with a separate subwoofer output. Since the AV receiver handles the bass management in this configuration, the settings for each loud speaker can be adjusted individually via the menu. Note: in this case, the LOW PASS setting of the subwoofer has no effect. Refer to the user manual of your AV receiver for information on the individual setup controls.
Setup Procedure The power amplifiers of some manufacturers feature separate MAIN IN and PRE OUT terminals, allowing the preamplified signal to reach the subwoofer and to be looped back again filtered. In this way the loudspeakers are relieved in the deep range, thus gaining in precision and sound characteristics. Refer to the appropriate manual for information about operation and connection options for your power amplifier.
Setup Procedure Commonly used configuration in stereo mode, loudspeakers to be connected parallel to the subwoofer (not recommended for Surround mode because of overcharge of small satellite speakers). In this configuration the PS 1 / PS 2 will be connected to the amplifier. Refer to the appropriate manual for information about operation and connection options for your stereo amplifier.
Settings of the Sound Characteristics Thanks to the use of the most advanced active electronics, your new subwoofer is a cutting edge product in the field of subwoofers. The connection and setting options provided on the subwoofer allow the best possible connection to your stereo or surround sound system and can be adapted to your individual audio requirements.
Daily Use From development to production, right down to quality testing, PIEGA only uses materials and components of the highest quality. The Top of your new subwoofer has a polished aluminum surface. As this material is very sensitive, it should be treated with care.
Warranty Conditions The warranty is limited to six years on our loudspeakers and three years on our electronics in accordance with the conditions stated below. Read through the service and warranty conditions carefully, especially the warnings concerning the purchase of PIEGA loudspeakers from unauthorized dealers. Warranty conditions 1. Every Piega device leaves the factory in perfect condition.
PIEGA SA Bahnhofstrasse 29 CH-8810 Horgen Telephone +41 44 725 90 42 Fax +41 44 725 91 92 mail@piega.ch www.piega.ch Information for Exports PIEGA SA Bahnhofstrasse 29 CH-8810 Horgen Telephone +41 44 725 90 02 Fax +41 44 725 91 92 mail@piega.ch www.piega.
