506 Twin Oaks Drive Johnson City, TN 37601 LUXURY PLUS SERIES Air and Whirlpool Therapy Bath Installation Instructions
TABLE OF CONTENTS Important Safety Information .........................................................................................................................3 Important Installation Information .................................................................................................................4 Testing Prior to Taking Indoors .......................................................................................................................
ATTENTION INSTALLER: SAVE THESE INSTRUCTIONS GIVE THIS MANUAL TO THE BATH OWNER. CONTAINS IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS READ AND FOLLOW ALL INSTRUCTIONS WARNING: Risk of accidental injury or drowning. Do not use this hydrotherapy bath unless all suction guards or intake covers for suction pumps are installed and in good condition to prevent body and hair entrapment. WARNING: Risk of accidental injury or drowning.
IMPORTANT!: Signature Baths are intended for indoor use only with installation in accordance with all instructions in this book. IMPORTANT!:To reduce the risk of personal injury and discoloration of the acrylic surface, water temperatures from the inlet should not exceed 140º F. Use supply lines suitable for 167º F, including the temperature rating of supply conductors to be used. IMPORTANT!: Do not drop or insert any object into any opening.
8. While the bath is still filled with water, plug the pump into a 120V GFCI outlet and allow to run for 10 minutes. Inspect for leaks. Inspect each jet and confirm water is flowing from each one. Turn the lights on and confirm each light is working. Rotate the waterfall valve to confirm the flow of water increases and decreases. *Your Signature Bath features a continuous flow waterfall.
ELECTRICAL CONNECTIONS DANGER: Risk of severe injury from electric shock or death by electrocution. This bath must be must be connected directly to a dedicated 120V 20 amp supply circuit that is protected by a Ground Fault Circuit Interrupter (GFCI) installed by a qualified, licensed electrician in accordance with national electric and local codes and the GFCI manufacturer’s instructions. The GFCI should be tested regularly. To test the GFCI, push the “TEST” button.
FRAMING THE BATH For proper drainage and stability, your Signature bath must be level and the full bottom of the full bath be seated firmly on the sub-floor. If the sub-floor requires leveling, measurements must be adjusted to include clearance for mortar between the floor and the bottom of the bath. The rim of the bath will not support weight. Three Wall Alcove Installation: The interior of the alcove must be the same size as the exterior dimension of the bath.
PLUMBING CONNECTIONS Important: Risk of damage to bath bottom and sub-floor. It is the installer’s responsibility to ensure watertight seal on installed connections. Important: Proper installation of the hardware and compliance with codes is the responsibility of the installer. Signature Bath does not warrant connections of water supply fittings and lines, fill systems, or drain/overflow systems and is not responsible for damage to the bath that occurs during installation.
OPERATING INSTRUCTIONS DANGER: Risk of accidental injury or drowning. Do not permit children to use this bath unless they are closely supervised by a responsible adult at all times. Never leave a full bath unattended. WARNING: Risk of severe injury by electric shock. Do not permit electric appliances (such as a hair dryer, lamp, telephone, radio or television) within 5 feet of this bath. WARNING: Risk of accidental injury or drowning.
Press to turn pump speed down. Minimum speed is 1. Press once to turn pulsating pump mode ON. Pump speed varies automatically every 10 seconds. Press a second time to turn pulsating pump mode OFF. Press once to turn lights ON, Press a second time to turn lights OFF. it Press once to turn air blower and lights ON. When button is pressed, the blower speed increases gradually for 5 seconds before returning to default setting. The “+”, “-” and “mode buttons are disabled during start up.
• • • • • • • • CARING FOR YOUR SIGNATURE BATH Do not use bubble bath or oil based additives in your Signature Bath. The bath should be drained after each use. Each bather should use fresh water. Certain cleaning products will permanently damage the bath surface. Read the product label carefully before use to be certain it specifically says it’s safe for acrylic surfaces.
SIGNATURE BATH MANUFACTURER’S LIMITED WARRANTY for Luxury and Luxury Plus Baths Warranty Coverage Throughout this document, Signature Bath shall be referred to as the “MANUFACTURER”. The following expressed limited lifetime warranty is given to the original consumer of a Luxury or Luxury Plus Series Signature Bath purchased for personal or single family residential use. Any commercial applications are excluded from all warranties.
506 Twin Oaks Drive Johnson City, TN 37601