Installation Guide

ManualsBrandsPioneer Faucets ManualsBathAmerican 8 in. Widespread 2-Handle Bathroom Faucet in Polished Chrome

Installation Guide

Two Handle Lavatory Widespread Faucet:

3AM400 •

This product meets the following standards:

ASME A112.18.1 •

ANSI A117.1 •

ANSI / NSF 61, SECTION 9 •

CUPC / IAPMO LISTED / ADA COMPLIANT•

CONTAINS NO MORE THAN 0.25% WEIGHTED •

AVERAGE LEAD CONTENT

REV-11 19, 12

Engineering Excellence

Engineering E xcellence

Summary of content (8 pages)

PAGE 1
Engineering Excellence Engineering E xcellence Installation Guide Two Handle Lavatory Widespread Faucet: • 3AM400 This product meets the following standards: • • • • • ASME A112.18.1 ANSI A117.1 ANSI / NSF 61, SECTION 9 CUPC / IAPMO LISTED / ADA COMPLIANT CONTAINS NO MORE THAN 0.25% WEIGHTED AVERAGE LEAD CONTENT Pioneer Industries, Inc.
PAGE 2
Thank you for purchasing this Pioneer quality product. Tools Required Adjustable Wrench Teflon Tape Rags 3/32” Allen Wrench Flex Hose Prior to Installation • Observe all local plumbing and building codes before you begin installation. • Carefully shut off both hot and cold water supplies. • Plug the sink drain with a soft cloth to prevent intrusion of debris or the loss of any parts. • Pioneer reserves the right to make changes in the design of faucets without notice.
PAGE 3
Faucet Installation • 1. 2. 3. 4. Note:- The spout & valve escutcheon is supplied with o-ring(B) to form watertight seal. Do not use o-ring(B) and plumbers putty both to form watertight seal. Place the spout escutcheon underneath of the spout(A). Ensure the o-ring(B) is placed underside of the escutcheon. Slide the spout(A) through center mounting hole. Slide the spout mounting washer(C) through spout shank from underside of center mounting hole. Thread and tighten the spout mounting nut(D).
PAGE 4
Faucet Installation 5. 6. 7. 8. The hot and cold side valves(H) are marked with ‘HOT’ and ‘COLD’ on the valve. Place washer(I) underneath of the ‘HOT’ side valve. Slide the valve through mounting hole. Place rubber washer(J) and steel washer(K) to the valve from underneath of the mounting surface. Ensure the handles are position correctly. Tighten the locknut(L) to the valve(H) with the help of 1-11/32” socket. Install the ‘COLD’ side valve same as ‘HOT’ side valve.
PAGE 5
Faucet Installation 9. Remove the pop-up stopper(N) and pop-up flange(O) from the pop-up assembly. 10. Apply adequate amount of plumbers putty underside of pop-up flange(O). Then insert pop-up drain assembly from underside of the sink and secure the pop-up flange(O) from the top. 11. Rotate the drain body so that horizontal rod hole faces back of the faucet. Hold the pop-up assembly in place and tighten the locknut(P). 12. Remove the excess putty. Connect the trap(Q).
PAGE 6
Faucet Installation 13. Remove rod nut(R). 14. Ensure the washers(S) is in place. Insert rod(T). Tighten the rod nut(R). 15. Push rod down to open drain. Insert the pop-up stopper(N) carefully. Test if the pop-up stopper(N) is working properly. 16. Connect pop-up bracket to the rod by using clip(V). Tighten the thumbscrew(U) to connect pop-up bracket to pop-up lift rod.
PAGE 7
Faucet Installation 17. Connect the supply stops to the inlet supply lines (left is hot water supply and right is cold water supply). Make sure inlet supply lines are securely tighten. Do not overtighten. Turn on supply stop. Remove aerator(W). 18. Check for any leaks. Make sure all the connection are secure. 19. Open the handles, flush and allow water to run at full flow for at least one minute. Close the handles. 20. Replace aerator(W).
PAGE 8
Engineering Excellence Engineering E xcellence 3325 S. Garfield Ave. | Commerce, CA 90040 Telephone: (800) 338-9468 | (323) 888-8873 | Fax: (323) 888-9515 Hours: M - F, 7:30am to 5:00pm PST www.pioneerind.