Installation Guide

ManualsBrandsPioneer Industries ManualsBathBrentwood Brushed Nickel 2-Handle 4-in Centerset WaterSense Bathroom Sink Faucet (Drain Included)

Installation Guide

Two Handle Lavatory Faucet:

3CB100* • 3BR120 • 3BR300*•

3CB101* • 3BR130* • 3BR310*•

3PR100* • 3BR200* • 3BR320•

3AM100* • 3BR210* • 3BR330*•

3BR100* • 3BR220 • 3MT100*•

3BR110* • 3BR230* • 3MT110*•

This product meets the following standards:

ASME A112.18.1 •

ANSI A117.1 •

ANSI / NSF 61, SECTION 9 •

CUPC / IAPMO LISTED / *ADA COMPLIANT•

CONTAINS NO MORE THAN 0.25% WEIGHTED •

AVERAGE LEAD CONTENT

REV-01 14, 13

Engineering Excellence

Engineering E xcellence

Summary of content (7 pages)

PAGE 1
Engineering Excellence Engineering E xcellence Installation Guide Two Handle Lavatory Faucet: • 3CB100* • 3BR120 • 3BR300* • 3CB101* • 3BR130* • 3BR310* • 3PR100* • 3BR200* • 3BR320 • 3AM100* • 3BR210* • 3BR330* • 3BR100* • 3BR220 • 3MT100* • 3BR110* • 3BR230* • 3MT110* This product meets the following standards: • • • • • ASME A112.18.1 ANSI A117.1 ANSI / NSF 61, SECTION 9 CUPC / IAPMO LISTED / *ADA COMPLIANT CONTAINS NO MORE THAN 0.
PAGE 2
Thank you for purchasing this Pioneer quality product. Tools Required Adjustable Wrench Teflon Tape Rags 3/32” Allen Wrench Prior to Installation • • • • • Observe all local plumbing and building codes before you begin installation. Carefully shut off both hot and cold water supplies from under the sink. Plug the sink drain with a soft cloth to prevent intrusion of debris or the loss of any faucet parts.
PAGE 3
Faucet Installation • • • • • Clean lavatory surface (A) from oil, grease or debris. Apply adequate amount of plumbers putty or sealant underneath of base plate. Lead the faucet shank (B) through faucet holes. Slide the mounting washers (C) through faucet shank (B). Thread and hand tighten the mounting nut (D) through faucet shank (B). Make sure both side of mounting nuts (D) are securely tighten.
PAGE 4
Pop-up Drain Installation 1. 2. 3. 4. 5. 6. 7. 8. Remove the pop-up stopper (E) and pop-up flange (F) from the pop-up assembly. Apply adequate amount of plumbers putty underside of pop-up flange (F) then insert pop-up drain assembly from underside of the sink and secure the pop-up flange (F) from the top. Rotate the drain body so that horizontal rod hole faces back of the faucet.Hold the pop-up assembly in place and tighten the locknut (G). Remove the excess putty.
PAGE 5
Pop-up Drain Installation 5 REV-01 14, 13
PAGE 6
Main Supply Connection • • • • • • Connect the faucet shank to inlet supply lines (N). Connect the supply stops (O) to the inlet supply lines (N) (left is hot water supply and right is cold water supply). Make sure inlet supply lines (N) are securely tighten. Do not overtighten. Turn on water. Check for any leaks. Make sure all the connections are secure. Remove aerator (P). Open the handle. Flush and allow water to run at full flow for at least one minute. Replace aerator (P).
PAGE 7
Engineering Excellence Engineering E xcellence 3325 S. Garfield Ave. | Commerce, CA 90040 Telephone: (800) 338-9468 | (323) 888-8873 | Fax: (323) 888-9515 Hours: M - F, 7:30am to 5:00pm PST www.pioneerind.