Installation Guide

ManualsBrandsPioneer Industries ManualsShower Heads4AM300T

Installation Guide

Single Handle Tub & Shower Trim Set:

4LG100T* • 4AM100T* • 4BR310T*•

4LG300T* • 4AM200T* • 4BR410T*•

4LG400T • 4BL100T* • 4AM300T* •

4BR120T • 4BL200T* • 4AM400T* •

4BR220T • 4BR100T* • 4BR320T•

4BL300T* • 4BR200T* • 4BR420T•

4BL400T* • 4BR300T* • 4BR130T*•

4DM100T* • 4BR400T* • 4BR230T*•

4DM200T* • 4BR110T* • 4BR330T*•

4DM300T* • 4BR210T* • 4BR430T*•

4DM400T* •

This product meets the following standards:

ASME A112.18.1 •

ANSI A117.1 •

CUPC / IAPMO LISTED / ADA COMPLIANT•

REV-01 17, 13

Engineering Excellence

Engineering E xcellence

Summary of content (9 pages)

PAGE 1
Engineering Excellence Engineering E xcellence Installation Guide Single Handle Tub & Shower Trim Set: • 4LG100T* • 4AM100T* • 4BR310T* • 4LG300T* • 4AM200T* • 4BR410T* • 4LG400T • 4BL100T* • 4AM300T* • 4BR120T • 4BL200T* • 4AM400T* • 4BR220T • 4BR100T* • 4BR320T • 4BL300T* • 4BR200T* • 4BR420T • 4BL400T* • 4BR300T* • 4BR130T* • 4DM100T* • 4BR400T* • 4BR230T* • 4DM200T* • 4BR110T* • 4BR330T* • 4DM300T* • 4BR210T* • 4BR430T* • 4DM400T* This prod
PAGE 2
Thank you for purchasing this pioneer quality product. Tools Required Teflon Tape 3/32” Allen Wrench Strap Wrench Thermometer Plumbers Putty Prior to Installation • Observe all local plumbing and building codes before you begin installation. • The finished wall and tub/shower valve(4020B) must be installed prior to installing this trim. • Pioneer reserves the right to make changes in the design of faucets without notice as specified in the pricebook. Caution: (1).
PAGE 3
Trim Installation • • • • • • • • • • Remove the temporary nipple. For Slip-Fit Installation (For 4LG100T,4BR1X0T, 4BR2X0T Only):The 1/2” nominal copper tube must be cut with a minimum length of A to maximum length of B from finished wall. The end of copper tube should be chamfered free of burrs to prevent cutting or nicking o-ring inside the tub spout. The outside surface may be sanded free from nicks and scratches.
PAGE 4
Trim Installation 4 REV-01 17, 13
PAGE 5
Trim Installation • • • • • • • • • Caution:- To avoid plugging the shower head spray outlet it is recommended to use teflon tape on the shower arm threads. Remove temporary nipple from the shower elbow. Use silicon to caulk the back of the shower arm flange(C). Slide the shower arm flange(C) over the shower arm(D). Apply the teflon tape on both threaded ends of shower arm(D) and install the shower arm(D) to the shower elbow. Carefully tighten with a clean strap wrench.
PAGE 6
Trim Installation 1. 2. 3. 4. 5. 6. Turn off the main water supply Remove test cap (F) with the help of 1-11/32” socket, ensure all the debris are flushed out of the system. relieve the water pressure. Thread sleeve (G) to the valve body. Insert the cartridge (H) to the valve body. Ensure the ‘UP’ symbol on the cartridge is on the top. Ensure the two notches underneath of the cartridge seats properly in the valve body. Hold the cartridge (H) and thread the locknut(I) to sleeve(G).
PAGE 7
Trim Installation 7 REV-01 17, 13
PAGE 8
Trim Installation • • • Slide the face plate(L) on the valve. Ensure the rubber gasket is placed behind the face plate (L) to form water tight seal. Secure the face plate(L) on the valve with the help of face plate screws (M). Use silicon to caulk around the face plate (L). Place the handle (N) on the stem. Secure the handle by tightening the allen screw (O). For 4DM100T,4DM200T & 4DM300T use 3/32” allen wrench and for 4LG100T & 4LG300T use 1/8” allen wrench.
PAGE 9
Engineering Excellence Engineering E xcellence 3325 S. Garfield Ave. | Commerce, CA 90040 Telephone: (800) 338-9468 | (323) 888-8873 | Fax: (323) 888-9515 Hours: M - F, 7:30am to 5:00pm PST www.pioneerind.