Installation Guide

ManualsBrandsPioneer Industries ManualsBathtub Faucets4BR810

Installation Guide

Two Handle Roman Tub Set:

4AM610* • 4BR710* • 4CL610*•

4MT610* • 4BR720 •

4MT620* • 4BR730*•

4BR600* • 4BR800*•

4BR610* • 4BR810*•

4BR620 • 4BR820•

4BR630* • 4BR830*•

4BR700*•

This product meets the following standards:

ASME A112.18.1 •

ANSI A117.1•

CUPC/ IAPMO LISTED/ *ADA COMPLIANT•

REV-10 31, 12

Engineering Excellence

Engineering E xcellence

Summary of content (8 pages)

PAGE 1
Engineering Excellence Engineering E xcellence Installation Guide Two Handle Roman Tub Set: • • • • • • • • 4AM610* 4MT610* 4MT620* 4BR600* 4BR610* 4BR620 4BR630* 4BR700* • • • • • • • 4BR710* 4BR720 4BR730* 4BR800* 4BR810* 4BR820 4BR830* • 4CL610* This product meets the following standards: • • • ASME A112.18.1 ANSI A117.1 CUPC/ IAPMO LISTED/ *ADA COMPLIANT Pioneer Industries, Inc.
PAGE 2
Thank you for purchasing this Pioneer quality product. Tools Required Adjustable Wrench Teflon Tape Rags 3/32” Allen Wrench Prior to Installation • Observe all local plumbing and building codes before you begin installation. • Carefully shut off both hot and cold water supplies. • Plug the tub drain with a soft cloth to prevent intrusion of debris or the loss of any parts. • Pioneer reserves the right to make changes in the design of faucets without notice.
PAGE 3
Valve Installation 1. 2. 3. 4. 5. 6. Thread the locknut (C) and rubber washer (B) from bottom of the spout shank (A). Slide the spout shank (A) from the spout mounting hole. Slide the rubber washer (B) from underneath of the shank. Thread the locknut (C) from underneath of the shank. Adjust the shank height to X” from finished deck or finished rim. Install the ‘T” connector (E) to beneath of the shank (A). Do not forget to place the washer (D) between the ‘T’ connector (E) and the shank (A).
PAGE 4
Valve Installation 4 REV-10 31, 12
PAGE 5
Valve Installation 7. 8. 9. 10. 11. 12. 13. Carefully install the hose (I) to the valve outlets. The other end connect it to ‘T‘ connector (E). Do not overtighten the hose with adjustable wrench as it may damage the valve assembly. Ensure that hot and cold side stems are turning in correct direction. Connect the valve assembly inlets to water supply tubes ( left is hot water supply and right is cold water supply). Do not overtighten the hose with adjustable wrench as it may damage the valve assembly.
PAGE 6
Valve Installation 6 REV-10 31, 12
PAGE 7
Trim Installation 14. After installed the finished deck , remove the mud guards. Ensure the supplied o-ring is placed underneath of the spout (K) 15. Install the spout (K) on the spout shank (A) and secure it with the help of allen screw (L). Place the hole cover (M). Clean the mounting surface if necessarry. 16. Install the cold side and hot side handle (N) by tightening screw with the help of philips head screwdriver. Place the cap on the handle (N). 17. Ensure the handle works properly.
PAGE 8
Engineering Excellence Engineering E xcellence 3325 S. Garfield Ave. | Commerce, CA 90040 Telephone: (800) 338-9468 | (323) 888-8873 | Fax: (323) 888-9515 Hours: M - F, 7:30am to 5:00pm PST www.pioneerind.