Installation & Assembly

ManualsBrandsPioneer ManualsBathroom Remodel & Bathroom FixturesLegacy Centerset Bathroom Faucet

Installation Guide

Single Handle Lavatory Faucet:

3LG160* • 3LG171* • 3LG170B* •

3LG161* • 3LG160B* • 3LG161G* •

3LG170* • 3LG180 • 3PM160* •

3LG180B • 3LG181 • 3LG160H* •

This product meets the following standards:

ASME A112.18.1 •

ANSI A117.1 •

ANSI / NSF 61, SECTION 9 •

CUPC / IAPMO LISTED / ADA COMPLIANT•

CONTAINS NO MORE THAN 0.25% WEIGHTED •

AVERAGE LEAD CONTENT

REV-01 14, 13

Engineering Excellence

Engineering E xcellence

Summary of content (9 pages)

PAGE 1
Engineering Excellence Engineering E xcellence Installation Guide Single Handle Lavatory Faucet: • 3LG160* • 3LG171* • 3LG170B* • 3LG161* • 3LG160B* • 3LG161G* • 3LG170* • 3LG180 • 3PM160* • 3LG180B • 3LG181 • 3LG160H* This product meets the following standards: • • • • • ASME A112.18.1 ANSI A117.1 ANSI / NSF 61, SECTION 9 CUPC / IAPMO LISTED / ADA COMPLIANT CONTAINS NO MORE THAN 0.25% WEIGHTED AVERAGE LEAD CONTENT Pioneer Industries, Inc.
PAGE 2
Thank you for purchasing this Pioneer quality product. Tools Required Adjustable Wrench Teflon Tape Rags 3/32” Allen Wrench Prior to Installation • • • • • Observe all local plumbing and building codes before you begin installation. Carefully shut off both hot and cold water supplies from under the sink. Plug the sink drain with a soft cloth to prevent intrusion of debris or the loss of any faucet parts.
PAGE 3
Faucet Installation • • • • • • • • Slide the base plate (A) to the underside of the faucet. Apply adequate plumbers putty or sealant along the boundary of the base plate (A) if necessary. Clean the mounting surface If necessary. Insert the faucet through sink hole. Thread the mounting bolt (B) into the faucet from beneath. Slide the mounting plate (C) through the mounting bolt. Thread the mounting nut (D) from underside. Secure the faucet to the sink with mounting nut (D) supplied with the faucet.
PAGE 4
Pop-up Drain Installation 1. 2. 3. 4. 5. 6. 7. 8. Remove the pop-up stopper (E) and pop-up flange (F) from the pop-up assembly. Apply adequate amount of plumbers putty underside of pop-up flange (F). Then insert pop-up drain assembly from underside of the sink and secure the pop-up flange (F) from the top. Rotate the drain body so that horizontal rod hole faces back of the faucet.Hold the pop-up assembly in place and tighten the locknut (G). Remove the excess putty.
PAGE 5
Pop-up Drain Installation 5 REV-01 14, 13
PAGE 6
Grid Drain Installation 1. 2. 3. 4. 5. Remove the grid trim ring (N) from the grid drain assembly (O). Apply adequate amount of plumbers putty underside of the grid trim ring (N). Attache the grid trim ring (N) from top of the drain hole. Insert the grid drain assembly (O) from under the lavatory sink. Hold the grid trim ring (N) in place while threading the locknut (P) until the locknut is snug with the underneath the lavatory sink. Tighten the locknut (P). Remove the excess putty.
PAGE 7
Main Supply Connection • • • • • • Connect the faucet inlet tubes (Q) to inlet supply lines (R). Connect the supply stops (S) to the inlet supply lines (R) (left is hot water supply and right is cold water supply). Make sure inlet supply lines (R) are securely tighten. Do not over- tighten. Turn on water. Check for any leaks. Make sure all the connections are secure. Remove aerator (T). Open the handle. Flush and allow water to run at full flow for at least one minute. Replace aerator (T).
PAGE 8
To Set or Adjust Temperature Limit Stop Caution: Ceramic cartridge is preset at the factory at maximum temperature. Adjust as necessary. Please see the instructions below: • • • • • • Turn off water and relieve the pressure. Remove handle (U) by removing Button (W) and loosening set screw (V) and lift off the handle (U). Note: For 3LG180, 3LG180B and 3LG181- Remove handle (U) by remove button (W) (located on the top of the handle) and loosening Phillips screw.
PAGE 9
Engineering Excellence Engineering E xcellence 3325 S. Garfield Ave. | Commerce, CA 90040 Telephone: (800) 338-9468 | (323) 888-8873 | Fax: (323) 888-9515 Hours: M - F, 7:30am to 5:00pm PST www.pioneerind.