PROJECTION MONITOR RECEIVER PRO-610HD PRO-510HD Operating Instructions
FEATURES Progressive Scan/HDTV READY 3D Y/C Separation Circuit Combination with the SH-D09 digital tuner, sold separately, makes it possible to receive all ATSC 18 formats. All SDTV and HDTV signals are converted to 1080i signals and displayed at high resolution. This three-dimensional Y/C separation circuit reproduces clearer picture quality.
Thank you for purchasing this PIONEER Projection Monitor Receiver. Please read the precautionary instructions enclosed with these operating instructions please do so before proceeding. After learning how to operate the Projection Monitor, be sure to keep this manual handy for future reference. WARNING: Read and understand these 'Operating Instructions' before operating your Monitor. Follow the 'IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS' section and all the warnings on the product.
The following symbols are found in this manual and on the labels on the product. They alert the operators and service personnel of this equipment to potentially dangerous conditions. This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death. This symbol indicates an action that is prohibited. This symbol refers to a hazard or unsafe practice which can result in personal injury or property damage.
Do not subject your Monitor to impact of any kind. Be particularly careful not to damage the screen surface. 10. Unplug the Monitor from the wall outlet before cleaning. Do not use liquid cleaners or spray-type cleaners. Use a damp cloth for cleaning. 11-1. Do not place this Monitor on an unstable, uneven or an inclined location. The Monitor may overturn, causing serious injury (to a person), and serious damage to the appliance. 11-2. Be careful when placing the Monitor on a cart to move it.
17. An outdoor antenna system should not be located in the vicinity of overhead power lines/ electric lights or power circuits, or where it can fall onto such power lines or circuits. When installing an outdoor antenna system, extreme care should be taken to keep it from touching such power lines or circuits as contact with them might be fatal. 18.
CONTENTS INTRODUCTION HOW TO READ THIS OPERATING INSTRUCTIONS ...................... 8 INSTALLING THE MONITOR ........................................................ 9 BASIC OPERATIONS BEFORE USE .............................................................................. CONNECTING THE ANTENNA ................................................... CONNECTING VIDEO/AUDIO EQUIPMENT ................................ FRONT PANEL FUNCTIONS .......................................................
HOW TO READ THIS OPERATING INSTRUCTIONS The following page is an example of the way that basic operating instructions are shown in this manual. The explanation method varies from page to page. AUTO CHANNEL PRESET The broadcast frequencies that can be received depend on your area. Memorize the broadcast stations that can be received in your area in the preset. 1 Select TV. 2 Press MENU and select SET UP by using the 5 or ∞ button and then pressing SET/ ENTER. (Refer to page 26.
INSTALLING THE MONITOR INSTALLATION PRECAUTIONS: DO NOT: • Do not use strong cleansers, solvents, polishes, or chemically treated cloths to clean the screen or cabinet. • Do not touch or scratch the screen. • Do not fasten or place rubber or vinyl items on the Monitor. • Do not stick adhesive tape onto the Monitor. • Do not put any object on the Monitor. DO: • Use a soft cloth to dust the screen and cabinet. • Handle the screen with care to avoid scratches or damages.
INSTALLING THE MONITOR HOW TO ATTACH THE PROVIDED PROTECTIVE SCREEN WE RECOMMEND ATTACHING THE PROTECTIVE SCREEN BEFORE USING THE MONITOR. To improve the image reproduction characteristics of the monitor and to protect the screen from damage or dust, attach the provided protective screen to the screen frame of the monitor following the given procedure. If you decide not to install the protective screen, attach the upper and lower panel frames as indicated and attach the corresponding trim.
INSTALLING THE MONITOR 5. Attach the remaining frame covers to the upper and lower panel frames: first, insert the edge of the frame cover into the outer groove of the panel frame, then starting at one end, push the inner part of the frame cover over the inner edge of the panel frame snapping it into place. Upper frame cover Panel frame Remove Attach Frame cover Side view Screws Lower frame cover HOW TO REMOVE THE PROTECTIVE SCREEN Five screws type Panel frame Side view Screws Three screws type 4.
BEFORE USE Before you watch the TV, perform the following procedure. For viewing DTV broadcasts, the SH-D09 digital tuner (sold separately) is necessary. For connecting the digital tuner, see page 78. UHF VHF Connect the cables of the VHF antenna and UHF antenna to the ANTENNA A terminal. (See pages 14 and 15) Mixer ANTENNA /CABLE A Connect the CATV converter to the ANTENNA B terminal. (See pages 14 and 15) B CATV converter ◊B√¿≥??ÙÛ Connect the power cord to the AC wall socket.
BEFORE USE Inserting batteries into the remote control unit BASIC OPERATIONS 1. CAUTION Incorrect use of batteries may lead to leakage or rupture. Always be sure to follow these instructions. A. Never mix new and used batteries. Two DURACELL® 'AA' MN1500 1.5V ALKALINE dry cell batteries 2. 9 ( B. Batteries of the same size may have different voltages depending on their type. Do not mix different types of batteries.
CONNECTING THE ANTENNA • A good color picture depends on a good TV signal. So does good multichannel (stereo program and SAP) sound. Ask your dealer for advice on how to install your external antenna to receive the best possible signal. • If you subscribe to Cable TV or have a central antenna for your building, you will not need an external antenna. Connect the TV signal source to your Monitor properly. Use a 75-ohm coaxial cable with an F-type connector and connect the cable as shown in the illustration.
CONNECTING THE ANTENNA Connecting the CATV converter with VCR ANTENNA /CABLE Cable TV Splitter A BASIC OPERATIONS CATV converter B VCR IN VCR OUT ANTENNA Connecting VHF/UHF antenna and CATV converter VHF antenna UHF antenna ANTENNA /CABLE A U/V mixer UHF VHF B Cable TV CATV converter 15
CONNECTING VIDEO/AUDIO EQUIPMENT DVD/LD player VCR ◊B√¿≥??ÙÛ VCR VCR VCR Video movie, etc. SAT tuner or Digital tuner • Refer to the instructions of your VCR or DVD/LD player for the detailed connections. • Before making or changing connections, set the power switch to off and unplug the power cord from the AC outlet. • If both the VIDEO terminal (pin-jack type) and S-VIDEO terminal are connected, the signals from the S-VIDEO terminal will have priority.
CONNECTING VIDEO/AUDIO EQUIPMENT SIGNAL VCR DVD/LD player BASIC OPERATIONS VCR OUTPUT AUDIO R L R V L R VIDEO S-VIDEO V L SIGNAL L V SIGNAL Use this terminal to input signals from an DVD/LD player which has a BNC video output terminal.
CONNECTING VIDEO/AUDIO EQUIPMENT Front panel S-VIDEO VIDEO L-AUDIO-R (MONO) R L VIDEO S-VIDEO OUTPUT INPUT 4 V L R R L V Video movie/VCR INPUT jacks COMPONENT VIDEO INPUT jack There are 4 sets of inputs for VCR and DVD/LD players. Use RCA-type pin plug cords (the same as those used in Hi-Fi systems) for connections. When the audio source to be connected is monaural, connect the source to the L-(MONO) jack.
CONNECTING VIDEO/AUDIO EQUIPMENT BASIC OPERATIONS ANTENNA /CABLE INPUTS INPUT INPUT 1 INPUT 2 INPUT 3 INPUT 1 OUTPUTS INPUT S-VIDEO A MONITOR /DTV TV CENTER VIDEO AUDIO VIDEO L (MONO) L AUDIO AUDIO R S-VIDEO/VIDEO RGB INPUT 3 SELECT R FIXED/VAR B COMPONENT VIDEO OUTPUT Y S-VIDEO/VIDEO INPUT 3 SELECT RGB PB CONTROL RGB IN OUT SIGNAL R L PR INPUT 3 INPUT Rear panel SIGNAL R L OUTPUT AUDIO R L RGB Digital tuner NOTE: Setting the INPUT 3 SELECT switch to ‘RGB’ will c
FRONT PANEL FUNCTIONS A flip-down door conceals the control panel. Push gently and release, to open the door. To close the door, lift it back up into place. 1 POWER STANDBY/ON indicator NOTE: If you accidentally pull the door, it may not shut properly. Push the door back in to shut it. 2 DTV indicator red: STANDBY green: ON Lights when receiving a digital television broadcast.
FRONT PANEL FUNCTIONS 8 RETURN button 0 INPUT 4 jacks Press to set the Projection Monitor to its initial mode. These inputs are for Video Movie and VCR. Use RCA-type pin plug cords (the same as those used in Hi-Fi systems) and SVIDEO cords for connections. When the audio source to be connected is monaural, connect the source to the L-(MONO) jack. Initial mode • Set to TV. Remains at the last channel set. Remains at the last setting. OFF CAUTION: STD Set to 0.
REMOTE CONTROL UNIT FUNCTIONS Set the mode switch to TV/DTV. 1 TV POWER button (STANDBY/ON) Turns the power of the monitor on and off. Mode switch 2 Input Selector buttons (TV, DTV*1, INPUT 1 to INPUT 4) Press the button to select the source you wish to watch. The screen will display your selection. TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF 1 TV POWER DTV 3 SCREEN MODE button Press to select the SCREEN MODE.
REMOTE CONTROL UNIT FUNCTIONS BASIC OPERATIONS 0 SPLIT/SEARCH screen buttons SPLIT: Press to turn the SPLIT screen function on and off. SEARCH: Press to select the SEARCH screen mode. SELECT: Selects the screen for switching the channel or input source.*2 FREEZE: When this button is pressed with the regular screen, the screen will change to the SPLIT screen and the picture at the time the button was pressed will become the sub-picture, displayed as a frozen image.
TO WATCH TV Best Horizontal and Vertical Viewing Angle • The optimum viewing angle is 140˚ in horizontal and 45˚ in vertical. • Watch from at least 10 feet (3m) away from the screen (optimum viewing distance is 10 to 23 feet). Remote control unit 1 ON/OFF POWER TV 1 2 DTV 3 SPLIT SEARCH SELECT INPUT 4 SCREEN ANT Turn on the POWER. The green STANDBY/ON indicator lights up. Remote control unit Control panel of the monitor Green indicator TV SUB CH MODE 140˚ Turn on the MAIN POWER switch.
TO WATCH TV VHF L TV 2-6 A-5(95) A-4(96) A-3(97) 2-6 A-2(98) (STD) A-1(99) 1-6 (HRC) (IRC) VHF H SUPER 7-13 A(14) B(15) C(16) D(17) E(18) 7-13 F(19) G(20) H(21) I (22) HYPER UHF 14-69 J(23) Q(30) W+1(37) W+11(47) W+21(57) W+31(67) W+41(77) W+51(87) W+61(102) W+71(112) W+81(122) K(24) R(31) W+2(38) W+12(48) W+22(58) W+32(68) W+42(78) W+52(88) W+62(103) W+72(113) W+82(123) L(25) S(32) W+3(39) W+13(49) W+23(59) W+33(69) W+43(79) W+53(89) W+63(104) W+73(114) W+83(124) M(26) T(33) W+4(40) W+14(50) W+24(
CHECKING THE MENU Press MENU on the remote control unit. The MAIN MENU will be displayed on the screen. Select the desired menu item using 5 or ∞ button of the remote control unit, and press SET/ENTER button to perform the desired operations and settings. EDIT/ TV/SAT/DVD LEARN MENU DTV/DVD TOP MENU SOURCE DTV/SAT 5 POWER 2 GUIDE 3 SET/ ENTER 8 INFO FAVORITE CH • When the menu screen appears, the mode will switch from SCREEN to FULL.
CHECKING THE MENU SCREEN setting menu (See page 39) 5 SET/ ENTER 3 ∞ SET/ ENTER SCREEN C I N EMA W I D E V .
AUTO CHANNEL PRESET The broadcast frequencies that can be received depend on your area. Memorize the broadcast stations that can be received in your area in the preset. 1 Select TV. 2 Press MENU and select SET UP by using the 5 or ∞ button and then pressing SET/ ENTER. (Refer to page 26.) 3 Select CHANNEL SET UP in the same way.
AUTO CHANNEL PRESET 6 Select TV/CABLE MODE , then select the broadcast system to be received from AIR, CATV STD, CATV HRC or CATV IRC.
CONVERGENCE ADJUSTMENT Earth magnetism may deviate the color misconvergence in some areas. After setting up the TV, or if the picture color is misconverged, be sure to realign color convergence, after the TV has warmed up for 30 minutes or more. TV/ CBL VCR DVD DTV /SAT /LD TV 1 Press MENU and select SET UP by using the 5 or ∞ button and then pressing SET/ ENTER. (Refer to page 26.) 2 Select CONVERGENCE in the same way.
CONVERGENCE ADJUSTMENT 4 Move the red line onto the green line. Move the vertical line. 5 SET/ ENTER 3 ON/OFF DTV TV POWER ∞ INPUT 1 2 3 4 SPLIT SEARCH SELECT ANT FREEZE USE: Move the horizontal line. SUB CH SCREEN MODE DTV AUDIO 5 DISPLAY 1 2 3 4 5 6 7 8 9 0 ENTER 2 AD J CONV E RG E NC E SET/ ENTER 3 SET/ ENTER ∞ USE: ¢ CH END: MENU 5 END: MENU Move the blue line onto the yellow line.
PROGRAM BLOCK (V. CHIP) FUNCTION Since laws have been passed in the United States requiring a way of blocking undesirable programming, the V-chip has become a required component in television sets. The V-chip is a computer chip which decodes signals added to broadcast signals transmitted by television broadcasters. These signals are classified by programming content (e.g., amount of violence or sexual content) and age, and viewers may specify settings which block certain types of programming.
PROGRAM BLOCK (V. CHIP) FUNCTION SETTING THE PROGRAM BLOCKING LEVEL 1 Press MENU and select SET UP by using the 5 or ∞ button and then pressing SET/ ENTER. (Refer to page 26.) 2 Select PROGRAM BLOCK in the same way.
PROGRAM BLOCK (V. CHIP) FUNCTION 5 Set BLOCK to ON. 5 2 SET/ ENTER TV/ CBL VCR DVD DTV /SAT /LD TV DTV EX I T INPUT 1 2 3 SPLIT SEARCH SELECT ANT FREEZE SUB CH 6 DTV AUDIO END: MENU Select MPAA RATING or TV PARENTAL GUIDELINES .
PROGRAM BLOCK (V. CHIP) FUNCTION 9 After setting, press MENU to turn the menu off. TV/SAT/DVD MENU HOW TO REMOVE BLOCKING FROM A PROGRAM IN PROGRESS REMOVING BLOCKING IN MULTI-SCREEN MODE • P R O G R AM B L O C K E D • MP A A R A T I N G :R _ _ _ _ Just as in normal single-screen mode, programs are blocked in SPLIT screen and SEARCH screen mode (see pages 40 and 41), but blocking may be removed only from the Main picture.
CHANGING PASSWORD A password must be entered to turn program blocking on and off. While the password is set to ‘1234’ at shipping time, it is strongly recommended that the password be changed after purchase. Note that this password is also used as the password required for the SHD09 digital tuner (sold separately). TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF POWER TV 1 2 3 SPLIT SEARCH SELECT ANT FREEZE 1 Press MENU and select SET UP by using the 5 or ∞ button and then pressing SET/ ENTER.
CHANGING PASSWORD 4 TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF TV POWER DTV Enter new password. • Press numeric buttons ‘0’ through ‘9’ to enter a four-digit password and press the SET/ENTER button.
CHANGING SCREEN SIZE SETTING SCREEN MODE The size of the picture or the picture's range projected on the screen can be changed between five screen sizes. Press the SCREEN MODE button. TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF POWER TV DTV 1 2 3 SPLIT SEARCH SELECT ANT FREEZE INPUT SCREEN 4 MODE SCREEN SUB CH MODE DTV AUDIO DISPLAY 1 2 3 4 5 6 7 8 9 0 ENTER • Each time the SCREEN MODE button is pressed, the mode changes in the following order.
CHANGING SCREEN SIZE TO ADJUST THE SCREEN POSITION In the CINEMA WIDE or ZOOM mode, the screen position can be adjusted to the top or bottom. TV/ CBL VCR DVD DTV /SAT /LD TV 1 Press MENU and select SCREEN by using the 5 or ∞ button and then pressing SET/ ENTER. (Refer to page 26.) 2 Select V. POSITION in the same way.
MULTI-SCREEN FUNCTION VIEWING TWO SCREENS (SPLIT screen) The screen can be split vertically, making it possible to view different images on the left and right. Press the SPLIT button. TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF POWER TV DTV ANT . A 3 6 INPUT 1 2 3 SPLIT SEARCH SELECT ANT FREEZE ANT . A 3 6 ANT .
MULTI-SCREEN FUNCTION SEARCHING FOR A PROGRAM ON A DIFFERENT CHANNEL (SEARCH screen) The screen on the right side can be made into nine or three different screens, making it possible to search for programs or enjoy multiple images. TV/ CBL VCR DVD DTV /SAT /LD TV Press the SEARCH button.
CLOSED CAPTION DECODE FUNCTION The closed caption broadcasting multiplexes caption signals (character information) in the video signal to allow the displaying of characters on the screen. This unit incorporates a closed caption decoder which allows, with the use of the remote control unit, to display character information when receiving character-multiplexed broadcasting signals (closed caption broadcasting) or playing a video cassette or Video Disc with the CC mark etc..
CHANGING CHANNEL SET UP TO ADD OR DELETE PRESET CHANNELS TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF DTV TV POWER INPUT 1 2 3 4 SPLIT SEARCH SELECT ANT FREEZE SUB CH SCREEN MODE DTV AUDIO Broadcast stations preset by auto channel preset which are unnecessary can be deleted. Broadcast stations to be watched that were not preset by auto channel preset can be preset. ADD ........... Manually presets channels that were not preset by AUTO CHANNEL PRESET. DEL ............
CHANGING CHANNEL SET UP 5 Select CHANNEL , then select a channel. 5 2 TV/ CBL VCR DVD DTV /SAT /LD TV 3 DTV EX I T INPUT 1 2 3 SPLIT SEARCH SELECT 5 SUB CH ANT FREEZE DTV AUDIO DISPLAY 1 2 3 4 5 6 7 8 9 0 ENTER 2 SET/ ENTER 3 CH 6 USE: END: MENU Select SETTING , then select ADD (addition) or DEL (deletion).
CHANGING CHANNEL SET UP 7 Select LABEL and input the label characters. • TV/ CBL VCR DVD DTV /SAT /LD TV 5 ON/OFF DTV TV POWER INPUT 1 2 3 SPLIT SEARCH SELECT 4 ANT FREEZE 2 SET/ ENTER 3 SET UP CHANN E L ADD / D E L AN T E NNA : A CHANN E L : 1 2 5 S E T T I NG : ADD L AB E L : ABCD SET/ ENTER ∞ SUB CH SCREEN MODE When ADD has been selected in step 6, a label of 4 characters can be input for the added channel.
CHANGING CHANNEL SET UP FAVORITE CHANNEL SET UP Assigning your favorite channels to the four buttons (blue, green, red and yellow) on the remote control unit makes it easy to call them up. Four channels can be assigned to each button, making it possible to set a total of 16 channels. TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF TV POWER DTV 1 Press MENU and select SET UP by using the 5 or ∞ button and then pressing SET/ ENTER. (Refer to page 26.) 2 Select CHANNEL SET UP in the same way.
CHANGING CHANNEL SET UP 5 Select number. SET UP F A VOR I T E CHANN E L Y E L L OW A N T CH 5 2 SET/ ENTER TV/ CBL VCR DVD DTV /SAT /LD TV ∞ ON/OFF DTV TV POWER 3 EX I T INPUT 1 2 3 SPLIT SEARCH SELECT ANT FREEZE USE: 114 56 23 5 SET/ ENTER END: MENU 4 SUB CH SCREEN MODE A B A A 1 2 3 4 6 Select antenna.
PICTURE ADJUSTMENTS This device has three types of picture quality settings in memory. You can select your favorite from them or set the picture quality you desire and store it in memory. RECALL THE DESIRED SETTINGS TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF DTV TV POWER 1 Press MENU and select PICTURE by using the 5 or ∞ button and then pressing SET/ENTER. (Refer to page 26.) 2 Select MODE in the same way.
PICTURE ADJUSTMENTS STORING THE SET PICTURE QUALITY IN MEMORY USER mode can be set for each input source: TV , DTV and INPUT 1 to INPUT 4. TV/ CBL VCR DVD DTV /SAT /LD TV 1 ON/OFF TV POWER DTV INPUT 1 2 3 4 SPLIT SEARCH SELECT Select the input source and show the image on the screen. ON/OFF SCREEN SUB CH ANT MODE TV DTV FREEZE INPUT DTV AUDIO 1 DISPLAY 2 3 4 5 6 7 8 9 0 ENTER ¢ 2 3 4 If VCR or DVD/LD has been selected, start playback for the relevant device.
PICTURE ADJUSTMENTS TO ADJUST THE PICTURE QUALITY The CONTRAST , BLACK LEVEL (brightness), COLOR, TINT and SHARP (sharpness) can be adjusted. TV/ CBL VCR DVD DTV /SAT /LD TV 1 Press MENU and select PICTURE . (Refer to page 26.) 2 Select the adjustment item.
PICTURE ADJUSTMENTS OTHER PICTURE QUALITY ADJUSTMENTS The following six fine adjustments are available. 1 3D Y/C LEVEL 2 3D NR LEVEL 3 COLOR TEMP (Color T emperature) 4 FLESH TONE 5 PURECINEMA 6 SVM (Scan V elocity Modulation) TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF DTV TV POWER INPUT 1 2 3 4 SPLIT SEARCH SELECT SUB CH SCREEN ANT MODE 1 Press MENU and select PICTURE . (Refer to page 26.) 2 Select OTHER .
PICTURE ADJUSTMENTS 2 To adjust 3D NR LEVEL Reduces the noise level of the luminance and chrominance signals when there is S-VIDEO input. NOTE: This function can be used only when viewing a source that has been connected to the S-VIDEO input terminal. TV/ CBL VCR DVD DTV /SAT /LD TV Select 3D NR LEVEL .
PICTURE ADJUSTMENTS 4 To adjust FLESH TONE By the time video signals from a broadcast station arrive at your projection monitor (on air or cable TV), they have experienced significant degradation. Flesh tone reduces color noise, improves color uniformity and corrects unnatural flesh tones to give your natural images. NOTE: This function cannot be used when 1080i or 480p component signals have been input or when a DTV broadcast is being watched (with the digital tuner, sold separately).
PICTURE ADJUSTMENTS Select the desired PURECINEMA mode. 5 2 3 ∞ TV/ CBL VCR DVD DTV /SAT /LD TV SET/ ENTER P U R E C I N EMA : ON/OFF STD USE: END: MENU DTV TV POWER SET/ ENTER INPUT 1 2 3 SPLIT SEARCH SELECT ANT FREEZE HQ ........... Maximum PURECINEMA effects. STD .......... Standard PURECINEMA effects. OFF ..........
SOUND ADJUSTMENTS WATCHING STEREO AND BILINGUAL PROGRAMS The multichannel TV sound (MTS) decoder enables stereo program and Second Audio Program (SAP) to be received. (SAP is often used for a second language). This MTS decoder can only be used if a broadcast of stereo program or SAP is received. TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF DTV TV POWER INPUT 1 2 3 4 SPLIT SEARCH SELECT ANT FREEZE 1 Press MENU and select SOUND by using the 5 or ∞ button and then pressing SET/ ENTER.
SOUND ADJUSTMENTS TO ADJUST THE SOUND QUALITY BASS, TREBLE and BALANCE can be adjusted. 1 Press MENU and select SOUND . (Refer to page 26.) 2 Select the adjustment item. TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF DTV TV POWER INPUT 1 2 3 4 SPLIT SEARCH SELECT ANT FREEZE SUB CH SCREEN MODE 5 DTV AUDIO DISPLAY 1 2 3 4 5 6 7 8 9 0 ENTER ¢ CH CH 2 SET/ ENTER ∞ 3 RETURN EX I T USE: SET/ ENTER END: MENU Adjust by pressing 2 or 3 .
SOUND ADJUSTMENTS TO SELECT THE DESIRED SURROUND MODE Surround can be selected as desired. TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF TV POWER 1 Press MENU and select SOUND . (Refer to page 26.) 2 Select SURROUND .
SOUND ADJUSTMENTS TO ADJUST SUPER BASS Use this function to enjoy powerful bass sounds. 1 Press MENU and select SOUND . (Refer to page 26.) 2 Select SUPER BASS .
DPO FUNCTION The sensor of the DPO (Dynamic Picture Optimizer) on the TV front panel determines brightness and adjusts the CONTRAST, BLACK LEVEL (brightness) and COLOR automatically. 1 Press MENU and select SET UP by using the 5 or ∞ button and then pressing SET/ ENTER. (Refer to page 26.) 2 Select DPO in the same way.
MULTI-POINT CONVERGENCE ADJUSTMENT Convergence adjustment may be fined-tuned from here. 1 Press MENU and select SET UP by using the 5 or ∞ button and then pressing SET/ ENTER. (Refer to page 26.) 2 Adjust the center point convergence. (Refer to steps 2 to 5 on pages 30 to 31.) 3 Select ADJ MULTI-POINT .
MULTI-POINT CONVERGENCE ADJUSTMENT 6 Adjust the blue line. 5 2 SET/ ENTER TV/ CBL VCR DVD DTV /SAT /LD TV ∞ ON/OFF DTV TV POWER INPUT SET/ ENTER A D J MU L T I - P O I N T S E T : NE X T PO I NT USE: 1 2 3 SPLIT SEARCH SELECT ANT FREEZE END: MENU 4 • SUB CH SCREEN MODE 3 DTV AUDIO The brackets which shows the adjusting point will move in order. Move to the next point to be adjusted, and repeat steps 4 to 6.
CONNECTION WITH RECEIVER (1) The audio signal output from this unit can be reproduced on the receiver when this monitor is connected to the receiver. When this monitor is connected to the CENTER OUT terminal of the receiver, the speaker of this monitor can be used as the center speaker. • Before making or changing connections, set the power switch to off and unplug the power cord from the AC outlet. • For details of connecting DVD/LD player, VCR, SAT tuner, etc., refer to page 16.
CONNECTION WITH RECEIVER (1) SPEAKER and AUDIO OUT settings 1 Press MENU and select SET UP by using the 5 or ∞ button and then pressing SET/ ENTER. (Refer to page 26.) 2 Select SYSTEM IN/OUT in the same way.
CONNECTION WITH RECEIVER (1) 5 Select AUDIO OUT . • TV/ CBL VCR DVD DTV /SAT /LD TV 5 ON/OFF TV POWER DTV INPUT 1 2 3 4 SPLIT SEARCH SELECT 2 SET/ ENTER ANT 3 SET UP S Y S T EM I N / O U T S P E A K E R : N O RM A L AUD I O OU T : F I X E D S Y S T EM MO D E : O F F SET/ ENTER ∞ SUB CH SCREEN MODE If the speaker mode was set to CENTER IN in step 4, the AUDIO OUT mode will automatically change to FIXED, and VAR cannot be selected.
CONNECTION WITH RECEIVER (2) This unit can be used as the monitor for the receiver when this unit is connected to the receiver. When this unit is connected to the CENTER OUT terminal of the receiver, the speaker of this unit can be used as the center speaker. • Before making or changing connections, set the power switch to off and unplug the power cord from the AC outlet. • Connect the DVD/LD player, VCR, SAT tuner or similar component to the receiver.
CONNECTION WITH RECEIVER (2) SYSTEM MODE setting 1 Press MENU and select SET UP . (Refer to page 26.) 2 Select SYSTEM IN/OUT .
CONNECTING THE SYSTEM REMOTE CONTROL (When operating Pioneer units with Î mark) When the control terminals of Pioneer audio/video units with the Î mark are connected, these units can be operated using the Monitor's remote control unit (see pages 72 to 77). CONTROL IN OUT To other units bearing the Î mark.
REMOTE CODE SET UP To operate other manufacturers' audio/video units using the TV remote control unit, remote control signals need to be set.
REMOTE CODE SET UP Manufacturer's preset remote control signals CBL/SAT PIONEER 1 PIONEER 2 JERROLD 1 JERROLD 2 JERROLD 3 JERROLD 4 JERROLD 5 JERROLD 6 JERROLD 7 JERROLD 8 JERROLD 9 JERROLD 10 S. A. 1 S. A. 2 S. A. 3 S. A.
REMOTE CODE SET UP TO LEARN REMOTE CONTROL SIGNALS To operate other manufacturers' remote control signals not preset using the remote control unit, have the remote control unit learn these signals. Example) To learn the VCR power to turn on. Before operation: To set the mode switch to VCR when a video cassette recorder is connected (see page 16).
REMOTE CODE SET UP • Buttons which can be learnt are as follows. CABLE ....... SOURCE POWER, CH (+), CH (–), CH RETURN, CH ENTER, 1 to 9, 0 SAT ........... SOURCE POWER, CH (+), CH (–), 2, 3, 5, ∞, SET/ENTER, TV/SAT/DVD MENU, DTV/SAT GUIDE, DTV/(SAT) INFO, CH ENTER, 1 to 9, 0 VCR ........... SOURCE POWER, CH (+), CH (–), 8, 1, 7, 3, ¡, ¶ (VCR REC) DVD .......... SOURCE POWER, ¢, 4, 8, 1, 7, 3, ¡, 2, 3, 5, ∞, SET/ENTER, TV/SAT/DVD MENU, DTV/DVD TOP MENU LD .............
REMOTE CODE SET UP USING THE TV REMOTE CONTROL UNIT TO CONTROL OTHER DEVICES Transmitting LED 2 TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF 3 POWER TV DTV 1 2 3 SPLIT SEARCH SELECT ANT FREEZE REMOTE CONTROL UNIT SETTING BUTTONS INPUT 4 SCREEN 1 EDIT/LEARN button EDIT: When the EDIT/LEARN button is pressed at the same time as number button 1, the mode will change to preset code edit mode. (See page 68.
REMOTE CODE SET UP 1 SCREEN MODE button Press to select the SCREEN MODE. Mode switch 2 DTV AUDIO button Press to select the audio mode during multiaudio broadcasts.
REMOTE CODE SET UP CABLE CONTROL BUTTONS Mode switch CABLE and SAT cannot be selected at the same time. When the mode switch is set to CBL/SAT the cable converter connected to the Monitor can be operated using the buttons 1 to 5. Cable converters which are made by other makers and are not preset can also be operated using the remote control unit if buttons 1 to 5 have learnt the functions (see page 70).
REMOTE CODE SET UP SAT CONTROL BUTTONS Mode switch CABLE and SAT cannot be selected at the same time. When SAT is preset by REMOTE CODE SET UP, the remote control unit buttons will function as shown below. • When a satellite broadcast tuner is connected to the Monitor, press the input selector button that has the same number as the connected input terminal and set the mode switch to CBL/SAT. The tuner can be operated using buttons 1 to 7.
REMOTE CODE SET UP VCR CONTROL BUTTONS Mode switch If the VCR is preset by REMOTE CODE SET UP, the remote control unit button will function as follows when the mode switch of the remote control unit is set to VCR. When the input selector button having the same number as the input terminal connecting the VCR is pressed, the VCR can be operated using buttons 1 to 8.
REMOTE CODE SET UP When the input selector button having the same number as the input terminal connecting a DVD player or LD player is pressed, these players can be operated using buttons 1 to (buttons 7 to 9 are for DVD players only). DVD player/LD player which are made by other makers and are not preset can also be operated using the remote control unit if buttons 1 to - have learnt the functions (see page 70).
USING THE DIGITAL TUNER (sold separately) TO WATCH DTV See the digital tuner installation manual for instructions on installing the SH-D09 digital tuner. 1 Connect the digital tuner. • Connect the VHF/UHF and Cable TV signal to the digital tuner. UHF VHF Digital tuner AIR Splitter CABLE ANTENNA Mixer ANTENNA /CABLE A Cable TV Splitter B Rear panel 2 Set the mode switch to TV/DTV and then press the DTV button.
USING THE DIGITAL TUNER (sold separately) TO WATCH DTV 4 Press the YELLOW button. • The screen to the right will appear. 5 Press 2, 3 to select the Digital Audio Out setting. TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF TV POWER DTV INPUT 1 2 3 SPLIT SEARCH SELECT 4 6 Press the YELLOW button. • The screen to the right will appear. SUB CH SCREEN ANT MODE FREEZE 7 Press 5, ∞, 2, 3 to select the Input Source and the CATV Mode.
USING THE DIGITAL TUNER (sold separately) TO WATCH DTV 5 Select a channel. Digital broadcast channels Ch 35 Ch 36 10:00am Highdefinition program Digital television 12:00pm 2:00pm Program A Ch 35.10 Program B Ch 35.40 Program C Ch 35.80 High-definition program Ch 36.20 Digital Television (DTV) is an exciting new digital broadcast standard that will provide vastly improved picture and sound quality compared to current NTSC (National Television Standards Committee) analog technology.
USING THE DIGITAL TUNER (sold separately) TO WATCH DTV There are four methods for this. TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF TV POWER 1 Select by pressing the number button and DTV button INPUT 1 2 3 4 SPLIT SEARCH SELECT SCREEN ANT MODE (Example) SUB CH Channel 12.34 ......... 1 → 2 → → 3 → 4 DISPLAY Channel 5.67 ......... 0 → 5 → → 6 → 7 FREEZE DTV AUDIO 1 2 3 4 5 6 7 8 9 0 CH ¢ ENTER • Press the button between the main and sub channels.
USING THE DIGITAL TUNER (sold separately) TO WATCH DTV RECORDING DTV PROGRAMS SIGNAL AIR CABLE ANTENNA Digital tuner ANTENNA /CABLE INPUTS INPUT INPUT 1 INPUT 2 INPUT 3 INPUT 1 INPUT OUTPUTS Mixer Splitter S-VIDEO A MONITOR /DTV CENTER TV VIDEO AUDIO VIDEO L AUDIO AUDIO R FIXED/VAR COMPONENT VIDEO Y S-VIDEO/VIDEO INPUT 3 SELECT RGB PB CONTROL RGB IN SIGNAL OUTPUT R B L R V L (MONO) OUT PR INPUT 3 INPUT Rear panel R L V INPUT R L AUDIO VIDEO VCR VCR for reco
USING THE DIGITAL TUNER (sold separately) TO WATCH DTV TV/ CBL VCR DVD DTV /SAT /LD TV ON/OFF DTV TV POWER INPUT 1 2 3 SPLIT SEARCH SELECT ANT FREEZE 1 Connect the rear panel MONITOR/DTV OUTPUT jack and the VCR input jack. 2 Select the channel of the DTV program you wish to record. (Refer to steps 2 to 5 on pages 78 to 81.) 3 Press MENU and select SET UP by using the 5 or ∞ button and then pressing SET/ ENTER. (Refer to page 26.) 4 Select DTV OUT in the same way.
USING THE DIGITAL TUNER (sold separately) TO WATCH DTV CONNECTION WITH RECEIVER • Before making or changing connections, set the power switch to off and unplug the power cord from the AC outlet. • After completing connections, perform the “SYSTEM MODE setting” operation. DOLBY DIGITAL AUDIO-OUT DIGITAL SIGNAL Connect the VHF/UHF signal to the digital tuner.
USING THE DIGITAL TUNER (sold separately) TO WATCH DTV 1 Set the SYSTEM MODE to ON. (Refer to page 66.) • • TV/ CBL VCR DVD DTV /SAT /LD TV • ON/OFF TV POWER DTV Monitor input will be fixed to INPUT 1 and the picture from the input source selected by the receiver displayed. To watch TV, switch the receiver input to where the monitor’s TV OUTPUT signal connects. Channels can be selected using the monitor’s remote control.
MENU INDEX Main menu (See page 26) PICTURE adjustment menu (See page 48) PICTURE SOUND SCREEN CC SET UP PICTURE MO D E : S T D CON T RA S T BLACK LVL .
MENU INDEX CHANNEL SET UP menu (See page 28) SET UP CHANN E L S E T UP AU T O CHANN E L PR E S E T CHANN E L ADD / D E L F A VOR I T E CHANN E L AUTO CHANNEL PRESET menu (See page 28) SET UP AU T O CHANN E L PR E S E T AN T E NNA : A T V / C A B L E MO D E : AIR AUTO PRE S E T S T ART EX I T USE: END: MENU CONVERGENCE menu (See pages 30 and 60) SET UP CONV E RG E NC E NA T URA L W I D E C I N EMA W I D E Z O OM F U L L A N D 4 : 3 N O RMA L F U L L F OR HD EX I T USE: EX I T USE: END: MENU CHANNE
TROUBLESHOOTING Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with the Monitor, check the points below. Sometimes the trouble may lie in another component. Investigate the other component and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.
TROUBLESHOOTING The following symptoms may be mistakenly regarded as malfunctioning. In many cases, they are not the faults of the Monitor. SYMPTOM CAUSE When there are 2 or 3 layers of images (ghost phenomenon) Influence of waves from the broadcast stations reflected by nearby mountains and high-rise buildings.
SPECIFICATIONS Display and amplifier section Electrical section, miscellaneous Reception system ........ American TV standard NTSC system Screen size ................................................. 58" (PRO-610HD) 53" (PRO-510HD) CRT ..................................................... 7" High focus CRT x 3 Brightness (White peak) ....... 420 Foot-Lambert (PRO-610HD) 500 Foot-Lambert (PRO-510HD) [White window signal input contrast Max.] without protective screen Horizontal resolution ......
OTHERS 91
Should this product require service in the U.S.A. and you wish to locate the nearest Pioneer Authorized Independent Service Company, or if you wish to purchase replacement parts, operating instructions, service manuals, or accessories, please call the number shown below. 800–421–1404 Please do not ship your product to Pioneer without first calling the Customer Service Department at the above listed number for assistance. PIONEER ELECTRONICS SERVICE, INC. CUSTOMER SERVICE DEPARTMENT P.O.