Black plate (1,1) English Installation Manual Manuel d’installation Français MULTIMEDIA NAVIGATION RECEIVER RECEPTEUR DE NAVIGATION MULTIMEDIA AVIC-8000NEX AVIC-7000NEX AVIC-6000NEX AVIC-5000NEX AVIC-X8610BS 1
Black plate (2,1) Contents Precautions Your new product and this manual 3 Important safeguards 3 Connection Precautions before connecting the system 5 Before installing this product 5 To prevent damage 6 – Notice for the blue/white lead 6 Parts supplied 7 Connecting the power cord (1) 8 Connecting the power cord (2) 10 Connecting the system 12 Connecting to separately sold power amp 13 Connecting an iPhone with Lightning connector 14 – Connecting via the USB port 14 – Connecting via the HDMI port 14 – Con
Black plate (3,1) Section Precautions 01 English Your new product and this manual Important safeguards ! The navigation features of this product (and the rear view camera option if purchased) are intended solely to aid you in the operation of your vehicle. It is not a substitute for your attentiveness, judgment and care when driving. ! Never use this product to route to hospitals, police stations, or similar facilities in an emergency. Please call the appropriate emergency number.
Black plate (4,1) Section 01 Precautions ! Certain country and government laws may prohibit or restrict the placement and use of this product in your vehicle. Please comply with all applicable laws and regulations regarding the use, installation and operation of this product.
Black plate (5,1) Section Connection WARNING Do not take any steps to tamper with or disable the parking brake interlock system which is in place for your protection. Tampering with or disabling the parking brake interlock system could result in serious injury or death. CAUTION ! If you decide to perform the installation yourself, and have special training and experience in the mobile electronics installations, please carefully follow all of the steps in the installation manual.
Black plate (6,1) Section 02 Connection To prevent damage WARNING ! Use speakers over 50 W (output value) and between 4 W to 8 W (impedance value). Do not use 1 W to 3 W speakers for this unit. ! The black cable is ground. When installing this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly connected to metal parts of the car’s body.
Black plate (7,1) Section Connection 02 English Parts supplied Parts marked (*) are supplied with AVIC8000NEX, AVIC-7000NEX and AVIC-6000NEX.
Black plate (8,1) Section 02 Connection Connecting the power cord (1) Yellow To terminal supplied with power regardless of ignition switch position. Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF. Orange/white To lighting switch terminal. Black (ground) To vehicle (metal) body. Note When a subwoofer is connected to this product instead of a rear speaker, change the rear output setting in the initial setting. (Refer to Operation Manual.
Black plate (9,1) Section Connection 02 English This product 14 cm (5-1/2 in.) Power supply Yellow/black (MUTE) If you use equipment with a mute function, connect that equipment to the Audio Mute lead. If not, keep the Audio Mute lead free of any connections. Power cord Fuse (10 A) Note Audio source will be set to mute or attenuate, while the following sounds will not be muted or attenuated. For details, refer to Operation Manual.
Black plate (10,1) Section 02 Connection Connecting the power cord (2) Pink (CAR SPEED SIGNAL INPUT) This product is connected here to detect the distance the vehicle travels. Always connect the vehicle’s speed detection circuit. Failure to make this connection will increase errors in the vehicle’s location display.
Black plate (11,1) Section Connection 02 English This product Power supply Power cord Violet/white (REVERSE-GEAR SIGNAL INPUT) This is connected so that this product can detect whether the vehicle is moving forwards or backwards. Connect the violet/white lead to the lead whose voltage changes when the shift lever is put in reverse.
Black plate (12,1) Section 02 Connection Connecting the system iDatalink adapter input Please refer to the instruction manual for the iDatalink adapter (sold separately). This product SiriusXM Connect Vehicle Tuner Please refer to the instruction manual for SiriusXM Connect Vehicle Tuner (sold separately). Antenna jack 4 m (13 ft. 1 in.) Wired remote input Please refer to the instruction manual for the Hard-wired remote control adapter (sold separately). Vehicle antenna GPS antenna 3.55 m (11 ft.
Black plate (13,1) Section Connection 02 English Connecting to separately sold power amp Power amp (sold separately) RCA cables Rear outputs (REAR OUTPUT) (sold separately) Power amp (sold separately) 15 cm (5-7/8 in.) Power amp (sold separately) Front outputs (FRONT OUTPUT) This product Power supply White, Red (SWL, SWR) Power cord Blue/white To system control terminal of the power amp (max. 300 mA 12 V DC).
Black plate (14,1) Section 02 Connection Connecting an iPhone with Lightning connector Notes ! For details on how to connect an external device using a separately sold cable, refer to the manual for the cable. ! For details concerning the connection, operations and compatibility of iPhone, refer to Operation Manual. Connecting via the USB port Connecting via the HDMI port 8000NEX 7000NEX 6000NEX The following cables are required for the connection.
Black plate (15,1) Section Connection 02 ® ! When you connect the High Speed HDMI Cable, use the lock tie to fix it securely. = For details, refer to Securing the High ® Speed HDMI Cable on page 18. Connecting via the RGB input 5000NEX X8610BS The following cables are required for the connection. ! VGA/USB interface cable for iPod / iPhone (CD-IV202AV) (sold separately) ! USB interface cable for iPod / iPhone (CDIU52) (sold separately) ! Lightning to VGA Adapter (Apple Inc.
Black plate (16,1) Section 02 Connection Connecting via the RGB input The USB interface cable for iPod / iPhone (CDIU201S) (sold separately) is required for the connection. USB port 1 This product Connecting the Android™ device 8000NEX 7000NEX 6000NEX App Connectivity Kit (CD-AH200) (sold separately) is required for the connection. Notes RGB input iPhone with 30-pin connector ! For details on how to connect an external device using a separately sold cable, refer to the manual for the cable.
Black plate (17,1) Section Connection 02 This product Connecting the MirrorLink™ device The USB interface cable for use with MirrorLink™ devices (CD-MU200) (sold separately) is required for the connection.
Black plate (18,1) Section 02 Connection Securing the High Speed HDMI® Cable 8000NEX 7000NEX 6000NEX Be sure to fix the High Speed HDMI® Cable with the lock tie, when you connect the external device with the High Speed HDMI® Cable. 1 Insert the High Speed HDMI® Cable into the HDMI port. 2 Wrap the lock tie around the hook above the HDMI port and the High Speed HDMI® Cable, and then tighten it to secure the High Speed HDMI® Cable.
Black plate (19,1) Section Connection 02 English Connecting a rear view camera Rear view camera (ND-BC6) (sold separately) When this product is used with a rear view camera, it is possible to automatically switch from the video to rear view image when the shift lever is moved to REVERSE (R). Camera View mode also allows you to check what is behind you while driving. To video output RCA cable (supplied with ND-BC6) WARNING USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA.
Black plate (20,1) Section 02 Connection Connecting the external video component Connecting the video component This product Using AV input You can connect an external video component or external camera to this product. Connecting an external camera This product 15 cm (5-7/8 in.) 23 cm (9 in.) Yellow (VIDEO INPUT OR CAMERA INPUT) Red, white (AUDIO INPUT) RCA cables (sold separately) 15 cm (5-7/8 in.
Black plate (21,1) Section Connection 02 CAUTION This product AUX input Be sure to use a mini-jack AV cable (CD-RM10) (sold separately) for wiring. If you use other cables, the wiring position might differ resulting in disturbed images and sounds. English Using an AUX input OK L V G R Mini-jack AV cable (CD-RM10) (sold separately) L: R: V: G V R G: L Left audio (White) Right audio (Red) Video (Yellow) Ground Mini-jack extension cable 2 m (6 ft. 7 in.
Black plate (22,1) Section 02 Connection Connecting an HDMI device Connecting the rear display 8000NEX 7000NEX 6000NEX This product This product Yellow (V OUT) Rear audio output HDMI port Mini pin plug cable (sold separately) High Speed HDMI® Cable (sold separately) To video input To audio inputs HDMI device (sold separately) Notes ! For details concerning the operations of HDMI device, refer to Operation Manual. ! When you connect the High Speed HDMI® Cable, use the lock tie to fix it securely.
Black plate (23,1) Section Installation CAUTION ! Never install this product in places where, or in a manner that: — Could injure the driver or passengers if the vehicle stops suddenly. — May interfere with the driver’s operation of the vehicle, such as on the floor in front of the driver’s seat, or close to the steering wheel or shift lever. ! Make sure there is nothing behind the dashboard or paneling when drilling holes in them.
Black plate (24,1) Section 03 Installation For AVIC-8000NEX and AVIC7000NEX users Do not install this product in a position where the opening of the LCD panel is obstructed by any obstacles, such as the shift lever. Before installing this product, be sure to leave sufficient space so that the LCD panel does not obstruct the shift lever when it is fully opened. This may cause interference with the shift lever, or a malfunction of the mechanism of this product.
Black plate (25,1) Section Installation 03 Do not cover this area. Installation using the screw holes on the side of this product % Fastening this product to the factory radio-mounting bracket. Position this product so that its screw holes are aligned with the screw holes of the bracket, and tighten the screws at three locations on each side. Use either the truss head screws (5 mm × 8 mm) or flush surface screws (5 mm × 9 mm), depending on the shape of the bracket’s screw holes.
Black plate (26,1) Section 03 Installation Fastening the detachable faceplate 6000NEX 5000NEX X8610BS If you do not plan to remove the detachable faceplate, the detachable faceplate can be fastened with the supplied screw.
Black plate (27,1) Section Installation 03 English Installing the GPS antenna Parts supplied CAUTION Do not cut the GPS antenna lead to shorten it or use an extension to make it longer. Altering the antenna cable could result in a short circuit or malfunction and permanent damage to this product. GPS antenna Metal sheet Installation notes ! The antenna should be installed on a level surface where radio waves will be blocked as little as possible.
Black plate (28,1) Section 03 Installation When installing the antenna inside the vehicle (on the dashboard or rear shelf) WARNING Do not install the GPS antenna over any sensors or vents on the dashboard of the vehicle, as doing so may interfere with the proper functioning of such sensors or vents and may compromise the ability of the metal sheet under the GPS antenna to properly and securely affix to the dashboard. 1 2 Make sure the surface is free of moisture, dust, grime, oil, etc.
Black plate (29,1) Section Installation 03 ! Install the microphone in a place where its direction and distance from the driver make it easiest to pick up the driver’s voice. ! Be sure to turn off (ACC OFF) the product before connecting the microphone. 2 Attach the microphone clip to the sun visor. 1 English Installing the microphone Parts supplied 2 Microphone Double-sided tape Mounting on the sun visor 1 Fit the microphone lead into the groove.
Black plate (30,1) Section 03 Installation Installation on the steering column 1 Detach the microphone base from the microphone clip by sliding the microphone base while pressing the tab. 1 Adjusting the microphone angle 2 4 1 2 3 4 1 Double-sided tape 2 Clamps Use separately sold clamps to secure the lead where necessary inside the vehicle. The microphone angle can be adjusted. 3 Microphone Tab Microphone base Microphone clip 2 Mount the microphone on the steering column.
Black plate (31,1) Section After installation 1 Reconnect the negative (–) terminal of the vehicle’s battery. First, double-check that all connections are correct and that this product is installed correctly. Reassemble all vehicle components that you previously removed. Then reconnect the negative (–) cable to the negative (–) terminal of the battery. 2 5 Drive down an unobstructed road until the GPS starts receiving the signal normally.
Black plate (32,1) Sommaire Précautions Votre nouveau produit et ce manuel 33 Importantes mesures de sécurité 34 Connexion Précautions à prendre avant de brancher le système 35 Avant d’installer ce produit 35 Pour éviter toute détérioration 36 – Remarque concernant le fil bleu/ blanc 37 Pièces fournies 37 Branchement du cordon d’alimentation (1) 38 Branchement du cordon d’alimentation (2) 40 Branchement du système 42 Connexion à un amplificateur de puissance vendu séparément 43 Connexion d’un iPhone avec
Black plate (33,1) Section Précautions Votre nouveau produit et ce manuel Si l’icône suivante s’affiche, la description s’applique uniquement au modèle indiqué. par ex. 8000NEX Français ! La fonction de navigation de ce produit (et la caméra de rétrovisée en option le cas échéant) est uniquement destinée à vous assister lors de la conduite de votre véhicule. Elle n’autorise en aucun cas un relâchement de votre attention, de votre jugement et de votre vigilance pendant la conduite.
Black plate (34,1) Section 01 Précautions Importantes mesures de sécurité AVERTISSEMENT Pioneer vous recommande de ne pas installer ce produit vous-même. Ce produit doit être exclusivement installé par un professionnel. Nous recommandons que seul le personnel d’entretien Pioneer agréé, qui dispose d’une formation et d’une expérience spéciales dans l’électronique mobile, configure et installe ce produit. N’INTERVENEZ JAMAIS SUR CE PRODUIT VOUS-MÊME.
Black plate (35,1) Section Connexion Précautions à prendre avant de brancher le système AVERTISSEMENT ATTENTION ! Si vous décidez de réaliser l’installation vous-même, et possédez une expérience spéciale en installation d’électronique automobile, veuillez suivre attentivement toutes les étapes du manuel d’installation. ! Attachez tous les fils avec des colliers ou des serre-câbles. Ne laissez aucun fil à nu. ! Ne raccordez pas directement le fil jaune conducteur de ce produit à la batterie du véhicule.
Black plate (36,1) Section Connexion OF Pas de position ACC ! Pour éviter les courts-circuits, recouvrez les fils déconnectés de ruban isolant. Il est particulièrement important d’isoler tous les fils conducteurs de haut-parleurs non utilisés pour éviter tout risque de court-circuit. ! Raccordez les connecteurs de même couleur au port de couleur correspondant, c’est-à-dire le connecteur bleu au port bleu, le noir au noir, etc.
Black plate (37,1) Section Connexion Remarque concernant le fil bleu/blanc Pièces fournies Les parties marquées d’un astérisque (*) sont fournies avec AVIC-8000NEX, AVIC-7000NEX et AVIC-6000NEX. Français ! Lorsque le commutateur d’allumage est sur Marche (ACC ON), un signal de commande est émis par le biais du fil bleu/ blanc.
Black plate (38,1) Section 02 Connexion Branchement du cordon d’alimentation (1) Jaune Vers la borne fournie avec l’alimentation quelle que soit la position du contacteur d’allumage. Rouge Vers la borne électrique commandée par le contacteur d’allumage (12 VCC) ON/OFF. Orange/blanc Vers la borne du contacteur d’éclairage. Noir (masse) Vers la carrosserie (métal) du véhicule.
Black plate (39,1) Section Connexion 02 Ce produit 14 cm Français Jaune/noir (MUTE) Si vous utilisez un équipement avec une fonction silence, connectez cet équipement sur le fil Audio Mute. Dans le cas contraire, ne rien connecter sur ce fil. Alimentation Fusible (10 A) Cordon d’alimentation Remarque La source audio sera coupée ou atténuée, alors que les sons suivants ne seront ni coupés ni atténués. Pour en savoir plus, reportez-vous au Manuel de fonctionnement.
Black plate (40,1) Section 02 Connexion Branchement du cordon d’alimentation (2) Rose (CAR SPEED SIGNAL INPUT) Ce produit est connecté ici pour détecter la distance parcourue par le véhicule. Toujours connecter le circuit de détection de vitesse du véhicule. Ne pas procéder à cette connexion augmente les erreurs dans l’afficheur d’emplacement du véhicule.
Black plate (41,1) Section Connexion 02 Ce produit Français Alimentation Cordon d’alimentation Violet/blanc (REVERSE-GEAR SIGNAL INPUT) Il est connecté afin que ce produit puisse détecter si le véhicule avance ou recule. Connectez le fil violet/blanc sur le fil dont la tension varie lorsque la marche arrière est enclenchée.
Black plate (42,1) Section 02 Connexion Branchement du système Entrée d’adaptateur iDatalink Reportez-vous au manuel d’instructions de l’adaptateur iDatalink (vendu séparément). Ce produit Syntoniseur pour véhicule SiriusXM Connect Reportez-vous au manuel d’instructions du syntoniseur pour véhicule SiriusXM Connect (vendu séparément). Prise d’antenne 4m Entrée de commande à distance câblée Reportez-vous au manuel d’instructions de l’adaptateur de commande à distance câblée (vendu séparément).
Black plate (43,1) Section Connexion 02 Connexion à un amplificateur de puissance vendu séparément Amplificateur de puissance (vendu séparément) Câbles RCA (vendus séparément) Sorties arrière (REAR OUTPUT) Français Amplificateur de puissance (vendu séparément) 15 cm Amplificateur de puissance (vendu séparément) Sorties avant (FRONT OUTPUT) Ce produit Blanc, rouge (SWL, SWR) Alimentation Cordon d’alimentation Bleu/blanc Vers la borne de commande du système d’amplificateur de puissance (300 mA 12
Black plate (44,1) Section 02 Connexion Connexion d’un iPhone avec connecteur Lightning Remarques ! Pour en savoir plus sur la connexion d’un périphérique externe à l’aide d’un câble vendu séparément, reportez-vous au manuel du câble. ! Pour en savoir plus sur la connexion, le fonctionnement et la compatibilité d’un iPhone, reportez-vous au Manuel de fonctionnement. Connexion via le port USB Connexion via le port HDMI 8000NEX 7000NEX 6000NEX Les câbles suivants sont nécessaires pour la connexion.
Black plate (45,1) Section Connexion 02 = Pour en savoir plus, reportez-vous à la ® page 48, Fixation du câble HDMI haute vitesse. Connexion d’un iPhone avec connecteur à 30 broches Remarques Connexion via l’entrée RGB Les câbles suivants sont nécessaires pour la connexion. ! Câble d’interface VGA/USB pour iPod / iPhone (CD-IV202AV) (vendu séparément) ! Câble d’interface USB pour iPod / iPhone (CD-IU52) (vendu séparément) ! Adaptateur Lightning vers VGA (produits Apple Inc.
Black plate (46,1) Section 02 Connexion Connexion via l’entrée RGB Le câble d’interface USB pour iPod / iPhone (CD-IU201S) (vendu séparément) est nécessaire pour la connexion. Port USB 1 Ce produit Connexion d’un périphérique Android™ 8000NEX 7000NEX 6000NEX Le kit de connexion aux applications (CDAH200) (vendu séparément) est nécessaire pour la connexion.
Black plate (47,1) Section Connexion 02 Connexion d’un périphérique Android via un port MHL Ce produit Connexion d’un périphérique MirrorLink™ Le câble d’interface USB utilisé avec les périphériques MirrorLink™ (CD-MU200) (vendu séparément) est nécessaire pour la connexion.
Black plate (48,1) Section 02 Connexion Fixation du câble HDMI® haute vitesse 8000NEX 7000NEX 6000NEX Veillez à fixer le câble HDMI® haute vitesse à l’aide de l’attache de blocage lorsque vous connectez un périphérique externe à l’aide du câble HDMI® haute vitesse. 1 Insérez le câble HDMI® haute vitesse dans le port HDMI. 2 Enroulez l’attache de blocage autour du crochet situé au-dessus du port HDMI et du câble HDMI® haute vitesse, puis serrezla afin de fixer le câble HDMI® haute vitesse.
Black plate (49,1) Section Connexion Connexion d’une caméra de rétrovisée 02 Caméra de rétrovisée (ND-BC6) (vendu séparément) Quand ce produit est utilisé avec une caméra de rétrovisée, il est possible de commuter automatiquement entre le signal vidéo et l’image de rétrovisée quand le levier de vitesse est placé sur la position REVERSE (R). Le mode Point de vue de la caméra vous permet également de vérifier ce qu’il y a derrière le véhicule quand vous conduisez.
Black plate (50,1) Section 02 Connexion Connexion d’un élément vidéo externe Connexion d’un composant vidéo Ce produit Utilisation de l’entrée AV Vous pouvez connecter un élément vidéo externe ou une caméra externe à ce produit.
Black plate (51,1) Section Connexion 02 Utilisation d’une entrée AUX Ce produit Entrée AUX ATTENTION Veillez à utiliser un câble AV mini-jack (CD-RM10) (vendu séparément) pour le raccordement. Si vous utilisez un autre type de câble, la position du raccordement pourrait différer, entraînant une déformation du son et des images.
Black plate (52,1) Section 02 Connexion Connexion d’un périphérique HDMI Connexion de l’afficheur arrière 8000NEX 7000NEX 6000NEX Ce produit Ce produit Jaune (V OUT) Sortie audio arrière Port HDMI Câble connecteur mini-prise (vendu séparément) Câble HDMI® haute vitesse (vendu séparément) Vers les entrées audio Appareil HDMI (vendu séparément) Remarques ! Pour en savoir plus sur le fonctionnement du périphérique HDMI, reportez-vous au Manuel de fonctionnement.
Black plate (53,1) Section Installation Précautions à prendre avant l’installation 03 ! ATTENTION ! ! ! ! Français ! Ne jamais installer ce produit dans un endroit ou de telle sorte qu’il : — risque de blesser le conducteur ou les passagers en cas d’arrêt brusque. — puisse interférer avec les commandes de manœuvre du conducteur tel que sur le plancher, en face du siège conducteur, ou à proximité du volant ou du levier de vitesse.
Black plate (54,1) Section 03 Installation Avant de procéder à l’installation ! Consultez le concessionnaire le plus proche si l’installation nécessite de percer des trous ou toute autre modification du véhicule. ! Avant d’installer ce produit définitivement, connectez le câblage provisoirement pour vous assurer que les connexions sont correctes et que le système fonctionne normalement. peut entraîner un dysfonctionnement de la localisation du véhicule.
Black plate (55,1) Section Installation 03 ! Les câbles ne doivent pas traverser la zone indiquée dans la figure ci-dessous, afin que la chaleur dégagée par les amplificateurs et le mécanisme de navigation puisse se dissiper librement. Installation en utilisant les trous de vis sur les côtés de ce produit Français % Fixez ce produit au support de montage radio d’usine.
Black plate (56,1) Section 03 Installation Fixation de la façade amovible 6000NEX 5000NEX X8610BS Si vous n’avez pas l’intention de retirer la façade amovible, vous pouvez la fixer en place avec la vis fournie.
Black plate (57,1) Section Installation 03 Installation de l’antenne GPS Pièces fournies ATTENTION Antenne GPS Plaque métallique Français Ne coupez pas le câble d’antenne GPS pour le raccourcir et n’utilisez pas d’extension pour le rallonger. Le fait d’intervenir sur le câble d’antenne risque d’entraîner un courtcircuit ou un dysfonctionnement et d’endommager de manière irrémédiable ce produit.
Black plate (58,1) Section 03 Installation Installation de l’antenne dans le véhicule (sur le tableau de bord ou la lunette arrière) AVERTISSEMENT N’installez pas l’antenne GPS par dessus un capteur ou une bouche d’air du tableau de bord du véhicule, car cela pourrait perturber le fonctionnement normal du capteur ou de la bouche d’air et compromettre la capacité de la plaque métallique sous l’antenne GPS d’assurer une fixation correcte et sûre sur le tableau de bord.
Black plate (59,1) Section Installation 03 Installation du microphone 2 Fixez l’agrafe pour micro au pare-soleil. 1 ! Installez le microphone dans un endroit permettant une bonne réception de la voix du conducteur. ! Éteignez ce produit (ACC OFF) avant de connecter le microphone. Français Pièces fournies 2 Microphone Bande adhésive à double face Installation sur le pare-soleil 1 Insérez le fil du microphone dans la fente.
Black plate (60,1) Section 03 Installation Installation sur la colonne de direction 1 Retirez la base du microphone de l’agrafe pour micro en faisant glisser la base du microphone tout en enfonçant la languette. 2 1 2 4 1 2 3 4 3 Microphone Languette Base du microphone Agrafe pour micro 2 Montez le microphone sur la colonne de direction. Installez le microphone sur la colonne de direction, à distance du volant.
Black plate (61,1) Section Après l’installation Après avoir installé ce produit 2 5 Roulez sur une route sans obstacle jusqu’à ce que le GPS commence à recevoir le signal normalement. Remarque Une fois l’installation terminée, vérifiez le bon fonctionnement du véhicule dans un endroit sécurisé. Français 1 Raccordez à nouveau la borne négative (–) de la batterie du véhicule. Vérifiez une nouvelle fois que toutes les connexions ont été bien faites et que ce produit est correctement installé.
Black plate (62,1) 62 Fr 62
Black plate (63,1) Français Fr 63 63
Black plate (64,1) PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, JAPAN PIONEER ELECTRONICS (USA) INC. P.O. Box 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 PIONEER ELECTRONICS OF CANADA, INC. 340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901 TEL: 905-479-4411 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique TEL: (0) 3/570.05.11 PIONEER ELECTRONICS ASIACENTRE PTE. LTD.