Black plate (1,1) English Operation Manual Manual de instrucciones Español CD Receiver Receptor de CD DEH-P7950UB 1
Black plate (2,1) Contents Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, keep this manual in a safe place for future reference.
Black plate (3,1) Contents English – Using balance adjustment 25 – Using the equalizer 25 – Adjusting loudness 26 – Using subwoofer output 26 – Boosting the bass 27 – Using the high pass filter 27 – Adjusting source levels 27 Initial Settings 28 – Adjusting initial settings 28 – Selecting the display language 29 – Setting the clock 29 – Setting the FM tuning step 29 – Setting the AM tuning step 29 – Switching the warning tone 29 – Switching the face auto open 30 – Switching the auxiliary setting 30 – Swit
Black plate (4,1) Contents – – – – – Clearing memory 46 Setting the automatic answering 46 Setting the automatic rejecting 46 Switching the ring tone 46 Echo canceling and noise reduction 47 – Displaying BD (Bluetooth Device) address 47 – Displaying system version for repair 47 Multi-CD Player 47 – Basic Operations 47 – Selecting a track directly 48 – Introduction of advanced operations 48 – Using ITS playlists 49 – Using disc title functions 50 – Using CD TEXT functions 50 DVD Player 51 – Basic Operatio
Black plate (5,1) Section Before You Start CAUTION ! Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, this unit damage, smoke, and overheat could result from contact with liquids. ! Keep this manual handy as a reference for operating procedures and precautions. ! Always keep the volume low enough so that you can hear sounds from outside the vehicle. ! Protect this unit from moisture.
Black plate (6,1) Section 01 Before You Start — iPod nano or 5 th generation iPod or later — Firmware Ver. 1.2 or later ! This unit can control previous generations of iPod with a Pioneer iPod adapter (e.g. CD-IB100N). In this case, most functions are essentially the same as iPod connected to USB interface of this unit. However, functions related to Audiobooks and Podcast can not be used. For details concerning operation with iPod adapter, refer to Playing songs on iPod on page 34.
Black plate (7,1) Section Before You Start 1 Make sure the inner cover is closed. 2 Replace the front panel by clipping it into place. Important The red lead (ACC) of this unit should be connected to a terminal coupled with ignition switch on/off operations. If this is not done, the vehicle battery may be drained.
Black plate (8,1) Section 01 Before You Start Use and care of the remote control Installing the battery Slide the tray out on the back of the remote control and insert the battery with the plus (+) and minus (–) poles pointing in the proper direction. ! When using for the first time, pull out the film protruding from the tray. Important ! Do not store the remote control in high temperatures or direct sunlight.
Black plate (9,1) Section Operating this unit 02 English b 12 a c 3 k 1 j i h 7 d e f g a 9 8 7 6 54 What’s What 7 DISPLAY button Press to select different displays. Head unit 8 SW button Press to select the subwoofer setting menu. Press and hold to select the bass boost setting menu. 1 SOURCE button This unit is turned on by selecting a source. Press to cycle through all the available sources.
Black plate (10,1) Section 02 Operating this unit Functions are the same as MULTI-CONTROL except for volume control. e DIRECT button Press to directly select the desired track. Power ON/OFF Turning the unit on % Press SOURCE to turn the unit on. f CLEAR button Press to cancel the input number when 0 to 9 are used. Turning the unit off g 0 to 9 buttons Press to directly select the desired track, preset tuning or disc.
Black plate (11,1) Section Operating this unit Adjusting the volume % Use MULTI-CONTROL to adjust the sound level. English ! External unit refers to a Pioneer product (such as one available in the future) that, although incompatible as a source, enables control of basic functions by this unit. Two external units can be controlled by this unit. When two external units are connected, the allocation of them to external unit 1 or external unit 2 is automatically set by this unit.
Black plate (12,1) Section 02 Operating this unit Storing and recalling broadcast frequencies Introduction of advanced operations You can easily store up to six broadcast frequencies for later recall. ! Up to 18 FM stations, six for each of the three FM bands, and six AM stations can be stored in memory. 1 Press MULTI-CONTROL to display the main menu. FUNCTION, AUDIO and ENTERTAINMENT appear on the display. 1 When you find a frequency that you want to store in memory press LIST.
Black plate (13,1) Section Operating this unit 3 Use MULTI-CONTROL to select the desired station. Turn to change the station; press to select. # You can also change the station by pushing MULTI-CONTROL up or down. English # To cancel the storage process, press MULTI-CONTROL again. 02 Built-in CD Player Basic Operations The built-in CD player can play back audio CD (CD-DA) and compressed audio (WMA/MP3/ AAC/WAV) recorded on CD-ROM. (Refer to page 59 for files that can be played back.
Black plate (14,1) Section 02 Operating this unit Disc loading slot 2 Insert a CD (CD-ROM) into the disc loading slot. Front panel is closed automatically, and playback will start. # Be sure to turn up the label side of a disc. # After a CD (CD-ROM) has been inserted, press SOURCE to select the built-in CD player. # You can eject a CD (CD-ROM) by pressing EJECT. 3 Push MULTI-CONTROL up or down to select a folder when playing a compressed audio.
Black plate (15,1) Section Operating this unit 1 Press MULTI-CONTROL to display the main menu. FUNCTION, AUDIO and ENTERTAINMENT appear on the display. 2 Use MULTI-CONTROL to select FUNCTION. Turn to change the menu option; press to select. The function name appears on the display. 3 Turn MULTI-CONTROL to select the function.
Black plate (16,1) Section 02 Operating this unit 3 When you find the desired track press MULTI-CONTROL to turn scan play off. # If the display has automatically returned to the playback display, select Scan mode again by using MULTI-CONTROL. # After scanning of a disc (folder) is finished, normal playback of the tracks will begin again. Pausing disc playback 1 Use MULTI-CONTROL to select Pause in the function menu. 2 Press MULTI-CONTROL to turn pause on. Playback of the current track pauses.
Black plate (17,1) Section Operating this unit 7 Press BAND to return to the playback display. Notes ! Titles remain in memory, even after the disc has been removed from the unit, and are recalled when the disc is reinserted. ! After data for 48 discs has been stored in memory, data for a new disc will overwrite the oldest one. ! If you connect a multi-CD player, you can input disc titles for up to 100 discs.
Black plate (18,1) Section 02 Operating this unit 1 Press LIST to switch to the file name list mode. Names of files and folders appear in the display. Playing songs on USB portable audio player/USB memory Basic Operations 1 2 Use MULTI-CONTROL to select the desired file name (or folder name). Turn to change the name of file or folder; press to play; push right to see a list of the files (or folders) in the selected folder.
Black plate (19,1) Section Operating this unit ! When the USB portable audio player having battery charging function connects to this unit and the ignition switch is set to ACC or ON, the battery is charged. ! You can disconnect the USB portable audio player/USB memory anytime you want to finish listening to. When disconnecting the USB portable audio player/USB memory from this unit during playback, No Device is displayed.
Black plate (20,1) Section Operating this unit 02 2 Use MULTI-CONTROL to select Random mode in the function menu. Displaying text information of an audio file 3 Press MULTI-CONTROL to turn random play on. Audio files will play in a random order. % Press DISPLAY to select the desired text information.
Black plate (21,1) Section Operating this unit Playing songs on iPod You can connect and listen to songs on an iPod with Dock Connector or USB interface. When using an iPod with Dock Connector, iPod Dock Connector to USB Cable is required. English # You can also change the name of file or folder by pushing MULTI-CONTROL up or down. # To return to the previous list (the folder one level higher), push MULTI-CONTROL left.
Black plate (22,1) Section 02 Operating this unit ! If an error message such as ERROR-11 is displayed, refer to Error messages on page 55. ! When the ignition switch is set to ACC or ON, the iPod’s battery is charged while the iPod is connected to this unit. ! While the iPod is connected to this unit, the iPod itself cannot be turned on or off. ! Before connecting the dock connector of this unit to the iPod, disconnect the headphones from the iPod.
Black plate (23,1) Section Operating this unit # You can also select the function by pressing FUNCTION on the remote control. # To return to the playback display, press BAND. # If you do not operate functions within about 30 seconds, the display is automatically returned to the ordinary display. Repeating play For playback of the songs on the iPod, there are two repeat play ranges: Repeat One (repeat one song) and Repeat All (repeat all songs in the list).
Black plate (24,1) Section 02 Operating this unit 2 Press MULTI-CONTROL to select your favorite setting. Press MULTI-CONTROL repeatedly until the desired setting appears in the display. Audio Adjustments Introduction of audio adjustments ! Faster – Playback faster than normal speed ! Normal – Playback in normal speed ! Slower – Playback slower than normal speed 1 1 Audio display Shows the audio adjustment status. 1 Press MULTI-CONTROL to display the main menu.
Black plate (25,1) Section Operating this unit You can change the fader/balance setting so that it can provide you an ideal listening environment in all occupied seats. 1 Custom1 Custom 1 Custom2 Custom 2 Flat Flat S.Bass Super bass English Using balance adjustment 02 Use MULTI-CONTROL to select Fader. # If the balance setting has been previously adjusted, Balance will be displayed. 2 Push MULTI-CONTROL up or down to adjust front/rear speaker balance.
Black plate (26,1) Section 02 Operating this unit +6 to –4 (or –6) is displayed as the equalizer curve is increased or decreased. +6 to –6 is displayed as the level is increased or decreased. # The actual range of the adjustments are different depending on which equalizer curve is selected. # The equalizer curve with all frequencies set to 0 cannot be adjusted. # You can then select another band and adjust the level.
Black plate (27,1) Section Operating this unit Adjusting subwoofer settings When the subwoofer output is on, you can adjust the cut-off frequency and the output level of the subwoofer. 1 Use MULTI-CONTROL to select Sub W.2. # You can also select the subwoofer setting menu by pressing SW on the unit. # When the subwoofer output is on, you can select Sub W.2. 2 Push MULTI-CONTROL left or right to select cut-off frequency.
Black plate (28,1) Section Operating this unit 02 1 Compare the FM tuner volume level with the level of the source you wish to adjust. 2 Initial Settings Adjusting initial settings Use MULTI-CONTROL to select SLA. 3 Push MULTI-CONTROL up or down to adjust the source volume. Each time MULTI-CONTROL is pushed up or down, source volume increases or decreases. SLA +4 to SLA –4 is displayed as the source volume is increased or decreased.
Black plate (29,1) Section Operating this unit 02 For your convenience, this unit equips multiple language display. You can select the language best suited to your first language. 1 Use MULTI-CONTROL to select Language select. 2 Press MULTI-CONTROL to select the language. Each press of MULTI-CONTROL selects languages in the following order: English—Español—Português Setting the clock Use these instructions to set the clock. 1 Use MULTI-CONTROL to select Clock.
Black plate (30,1) Section Operating this unit 02 Switching the face auto open To protect against theft, this unit features detachable front panel. To detach the front panel easily, the front panel opens automatically. This function is on as a default. 1 Use MULTI-CONTROL to select Face auto open. 2 Press MULTI-CONTROL to turn the face auto open on. # To turn the face auto open off, press MULTI-CONTROL again.
Black plate (31,1) Section Operating this unit 02 reverse, and then continue reversing every 10 seconds. Sound from this system is muted or attenuated automatically when the signal from the equipment with mute function is received. ! The sound is muted or attenuated, MUTE or ATT are displayed and no audio adjustment is possible. ! Sound from this system returns to normal when the muting or attenuation is canceled. 1 Use MULTI-CONTROL to select Reverse mode. 1 Use MULTI-CONTROL to select Mute.
Black plate (32,1) Section 02 Operating this unit Entering PIN code for Bluetooth wireless connection To connect your cellular phone to this unit via Bluetooth wireless technology, you need to enter PIN code on your phone to verify the connection. The default code is 0000, but you can change this in this function.
Black plate (33,1) Section Operating this unit Setting the AUX title The title displayed for each AUX1 or AUX2 source can be changed. 1 After you have selected AUX as the source, use MULTI-CONTROL and select FUNCTION to display TitleInput "A". 2 Enter a title in the same way as the built-in CD player. For details concerning operation, refer to Entering disc titles on page 16. Turning the clock display on or off You can turn the clock display on or off.
Black plate (34,1) Section 03 Available accessories Playing songs on iPod Listening to songs on your iPod You can use this unit to control an iPod adapter, which is sold separately. 1 3 2 1 Song number indicator 2 Play time indicator 3 Song time (progress bar) 1 Press SOURCE to select iPod. While the iPod is connected to this unit, PIONEER (or (check mark)) is displayed on the iPod. 2 To perform fast forward or reverse, push and hold MULTI-CONTROL left or right.
Black plate (35,1) Section Available accessories % Press DISPLAY to select the desired text information. Play time— : album title and play time— : song title and play time— : artist name and play time— : artist name and : album title — : song title and : album title # If the characters recorded on the iPod are not compatible with this unit, those characters will not be displayed.
Black plate (36,1) Section 03 Available accessories Bluetooth Audio Basic Operations If you connect Bluetooth adapter (e.g. CDBTB100) to this unit, you can control Bluetooth audio player via Bluetooth wireless technology. Important ! Depending on the Bluetooth audio player connected to this unit, the available operations with this unit are limited to the following two levels: — Lower level: Only playing back songs on your audio player is possible.
Black plate (37,1) Section Available accessories 1 Press MULTI-CONTROL to display the main menu. FUNCTION, AUDIO and ENTERTAINMENT appear on the display. 2 Use MULTI-CONTROL to select FUNCTION. Turn to change the menu option; press to select. The function name appears in the display. 3 Turn MULTI-CONTROL to select the function.
Black plate (38,1) Section 03 Available accessories 2 Press MULTI-CONTROL to stop the playback. Playback of the current song stops. Disconnecting a Bluetooth audio player 1 Use MULTI-CONTROL to select Disconnect audio in the function menu. 2 Press MULTI-CONTROL to disconnect the Bluetooth audio player. Disconnected is displayed. The Bluetooth audio player is now diconnected from this unit. Displaying BD (Bluetooth Device) address 1 Use MULTI-CONTROL to select Device info in the function menu.
Black plate (39,1) Section Available accessories ! Battery strength indicator may differ from the actual battery strength. ! If the battery strength is not available, nothing is displayed in the battery strength indicator area. 5 Incoming call notice indication Shows when an incoming call has been received and not checked yet. ! Incoming call notice is not displayed for calls made when your cellular phone is disconnected from this unit.
Black plate (40,1) Section 03 Available accessories Taking a phone call Answering an incoming call 1 When a call comes in, push MULTI-CONTROL up. # If the private mode is selected on the cellular phone, hands-free phoning may not be performed. 2 To end the call, push MULTI-CONTROL down. The estimated call time appears in the display (this may differ slightly from the actual call time). Rejecting an incoming call % When a call comes in, push MULTI-CONTROL down. The call is rejected.
Black plate (41,1) Section Available accessories # You can also select the function by pressing FUNCTION on the remote control. # PH.B.Name view (phone book name view) cannot be selected for cellular phone registered guest phone. # If cellular phone is connected to this unit via Bluetooth wireless technology with HSP (Head Set Profile), PH.B.Name view, Clear memory, Number dial and Refuse calls cannot be selected. # To return to the playback display, press BAND.
Black plate (42,1) Section 03 Available accessories Registering connected cellular phone 1 Use MULTI-CONTROL to select Set phone in the function menu. 2 Push MULTI-CONTROL up or down to select a registration assignment. P1 (user phone 1)—P2 (user phone 2)—P3 (user phone 3)—G1 (guest phone 1)—G2 (guest phone 2) # As you select each assignment, you can see whether or not a phone is already registered there. If the assignment is empty, No data is displayed.
Black plate (43,1) Section Available accessories 2 Press MULTI-CONTROL to enter in the phone book transfer standby mode. Transfer appears in the display. 3 Use cellular phone to perform phone book transfer. Perform phone book transfer using the cellular phone. For detailed instruction on this, refer to the instruction manual that came with your cellular phone. # The display indicates how many entries have been transferred and the total number to be transferred.
Black plate (44,1) Section 03 Available accessories Alphabet (upper case), numbers and symbols —alphabet (lower case)—numbers and symbols—European characters, such as those with accents (e.g., á, à, ä, ç) or Russian characters # Pressing and holding DISPLAY enables you to switch character set between ISO8859-1 (European characters) and ISO8859-5 (Russian characters) alternately. # European characters and Russian characters can’t be mixed.
Black plate (45,1) Section Available accessories Using the Call History Important You are required to park your vehicle and set the parking brake in order to perform this operation. The 12 most recent calls made (dialled), received and missed, are stored in the Call History. You can browse the Call History and call numbers from it. 1 Press LIST to display the list.
Black plate (46,1) Section 03 Available accessories 1 Use MULTI-CONTROL to select Number dial in the function menu. # You can also enter in this menu from the standby display by pressing DIRECT on the remote control. 3 Push MULTI-CONTROL right to determine the item that you want to delete from this unit. Clear memory YES is displayed. Clearing memory is now on standby. 2 Push MULTI-CONTROL up or down to select a number.
Black plate (47,1) Section Available accessories 03 Multi-CD Player 1 Use MULTI-CONTROL to select Echo cancel in the function menu. Basic Operations 2 Press MULTI-CONTROL to turn echo canceling on. # To turn echo canceling off, press MULTI-CONTROL again. Displaying BD (Bluetooth Device) address 1 Use MULTI-CONTROL to select Device info in the function menu. The device name (Pioneer BT Unit) of this unit appears in the display.
Black plate (48,1) Section 03 Available accessories Notes ! When the multi-CD player performs the preparatory operations, Ready is displayed. ! If an error message such as ERROR-11 is displayed, refer to the multi-CD player owner’s manual. ! If there are no discs in the multi-CD player magazine, No disc is displayed. Selecting a track directly The operation is basically the same as that of the built-in CD player. For details concerning operation, refer to Selecting a track directly on page 14.
Black plate (49,1) Section Available accessories ! If you select other discs during repeat play, the repeat play range changes to M-CD repeat. ! If you perform track search or fast forward/reverse during Track repeat, the repeat play range changes to Disc repeat. ! After track or disc scanning is finished, normal playback of the tracks will begin again. ! When playing a CD TEXT disc on a CD TEXT compatible multi-CD player, you cannot switch to TitleInput "A".
Black plate (50,1) Section 03 Available accessories 2 Use MULTI-CONTROL to select ITS memo in the function menu. 3 Select the desired track by pushing MULTI-CONTROL left or right. 4 Push MULTI-CONTROL down to erase the track from your ITS playlist. The currently playing selection is erased from your ITS playlist and playback of the next track from your ITS playlist begins. # If there are no tracks from your playlist in the current range, ITS empty is displayed and normal play resumes.
Black plate (51,1) Section Available accessories English The operation is the same as that of the builtin CD player. Refer to Displaying text information on disc on page 17. 03 DVD Player Basic Operations You can use this unit to control a DVD player or multi-DVD player, which is sold separately. For details concerning operation, refer to the DVD player’s or multi-DVD player’s operation manual.
Black plate (52,1) Section 03 Available accessories Selecting a disc ! You can operate this function only when a multi-DVD player is connected to this unit. % Press any of 1 to 6 on the remote control to select the desired disc. Selecting a folder ! You can operate this function only when a DVD player which is corresponding to compressed audio playback is connected to this unit. % Push MULTI-CONTROL up or down to select a folder.
Black plate (53,1) Section Available accessories Refer to Using ITS playlists on page 49. TitleInput "A" Refer to Entering disc titles on page 16. Notes ! If you select other discs during repeat play, the repeat play range changes to Disc repeat. ! During video CD or CD playback, if you perform track search or fast forward/reverse during Track repeat, the repeat play range changes to Disc repeat.
Black plate (54,1) Section 03 Available accessories Storing and recalling broadcast stations Storing the strongest broadcast stations sequentially You can easily store up to 12 broadcast stations for later recall. ! Up to 24 stations, 12 for each of two TV bands, can be stored in memory. 1 Press MULTI-CONTROL to display the main menu. FUNCTION, AUDIO and ENTERTAINMENT appear on the display. 1 When you find a station that you want to store in memory press LIST.
Black plate (55,1) Appendix Additional Information When you contact your dealer or your nearest Pioneer Service Center, be sure to record the error message. The connected USB portable audio player/ USB memory contains WMA files that are protected by Windows Media DRM 9/10 Play an audio file not protected by Windows Media DRM 9/10.
Black plate (56,1) Appendix Additional Information iPod Message Cause Action ERROR-11 Communication failure Disconnect the cable from iPod. Once iPod main menu is displayed, connect the cable again. Reset the iPod. ERROR-21 Old version of iPod Update the iPod version. ERROR-30 iPod failure Reset the iPod. ERROR-A0 iPod is not charged but operates correctly Check if the connection cable for iPod shorted out (e.g., not caught in metal objects).
Black plate (57,1) Appendix Additional Information USB audio player/USB memory USB audio player/USB memory compatibility ! Specification: USB 2.0 full speed ! USB Class: MSC (Mass Storage Class) device ! Protocol: bulk ! Maximum amount of memory: 250 GB ! File system: FAT12, FAT16, FAT32 ! Supply current: 500 mA Notes ! Partitioned USB memory is not compatible with this unit.
Black plate (58,1) Appendix Additional Information The sequence of audio files on USB memory For USB portable audio players, the sequence is different from that of USB memory and depends on the player. Example of a hierarchy : Folder : Compressed audio file 1 2 3 4 5 6 Level 1 Level 2 Level 3 Level 4 ! 01 to 05 represent assigned folder numbers. 1 to 6 represent the playback sequence. The user cannot assign folder numbers and specify the playback sequence with this unit.
Black plate (59,1) Appendix Additional Information ! You cannot operate the iPod Equalizer on the Pioneer products. We recommend that you set the iPod Equalizer to off, before connecting the iPod to this unit. ! You cannot set Repeat to off on the iPod when using this unit. Even if you set Repeat to off on the iPod, Repeat is changed to All automatically when connecting the iPod to this unit.
Black plate (60,1) Appendix Additional Information AAC ! Compatible format: AAC encoded by iTunes® version 6.0.5 and earlier ! Sampling frequency: 11.025 kHz to 48 kHz ! Transmission rate: 16 kbps to 320 kbps ! Apple Lossless: No WAV ! Compatible format: Linear PCM (LPCM), MS ADPCM ! Quantization bits: 8 and 16 (LPCM), 4 (MS ADPCM) ! Sampling frequency: 16 kHz to 48 kHz (LPCM), 22.05 kHz to 44.
Black plate (61,1) Appendix Additional Information General Rated power source ............... 14.4 V DC (allowable voltage range: 12.0 V to 14.4 V DC) Grounding system ................... Negative type Max. current consumption ..................................................... 10.0 A Dimensions (W × H × D): DIN Chassis ..................... 178 × 50 × 165 mm Nose ........................... 188 × 58 × 16 mm D Chassis ..................... 178 × 50 × 165 mm Nose ...........................
Black plate (62,1) Contenido Gracias por haber comprado este producto Pioneer. Lea con detenimiento estas instrucciones sobre el funcionamiento del aparato, para que pueda darle el mejor uso posible. Una vez que las haya leído, conserve este manual en un lugar seguro para consultarlo en el futuro.
Black plate (63,1) Contenido – Activación y desactivación de la visualización del reloj 97 – Uso de diferentes visualizaciones de entretenimiento 97 – Uso del botón PGM 97 Español – Cambio de la velocidad del audiolibro 86 Ajustes de audio 87 – Introducción a los ajustes de audio 87 – Uso del ajuste del balance 87 – Uso del ecualizador 88 – Ajuste de la sonoridad 89 – Uso de la salida de subgraves 89 – Intensificación de los graves 90 – Uso del filtro de paso alto 90 – Ajuste de los niveles de la fuente
Black plate (64,1) Contenido – Registro del teléfono móvil conectado 107 – Eliminación de un teléfono registrado 108 – Conexión a un teléfono móvil registrado 108 – Uso del Directorio de teléfonos 109 – Uso del Historial de llamadas 111 – Uso de números prefijados 111 – Realización de una llamada ingresando el número de teléfono 112 – Borrado de la memoria 112 – Ajuste de la respuesta automática 113 – Ajuste del rechazo automático 113 – Cambio del tono de llamada 113 – Cancelación del eco y reducción de r
Black plate (65,1) Sección Antes de comenzar Acerca de esta unidad PRECAUCIÓN Acerca de WMA El logo de Windows Media™ impreso en la caja indica que esta unidad puede reproducir datos WMA. WMA es la abreviatura de Windows Media Audio, y se refiere a la tecnología de compresión de audio desarrollada por Microsoft Corporation. Los datos WMA se pueden cifrar con la versión 7 o posterior del Windows Media Player.
Black plate (66,1) Sección 01 Antes de comenzar Compatibilidad con iPod® Esta unidad permite el control y la escucha de canciones en un iPod. Puede conectarse y escuchar canciones en un iPod con el conector del Dock o con el interfaz USB. ! Cuando utiliza un iPod con el conector del Dock, se requiere un conector Dock del iPod para el cable USB. ! El cable de interfaz CD-IU50 de Pioneer también está disponible. Para obtener información, consulte a su concesionario.
Black plate (67,1) Sección Antes de comenzar Extracción de la carátula 1 Mantenga presionado EJECT para abrir la carátula. Reinicialización del microprocesador Se debe reinicializar el microprocesador si se presentan las siguientes condiciones: ! Antes de utilizar esta unidad por primera vez después de su instalación ! Si la unidad no funciona correctamente ! Cuando aparecen mensajes extraños o incorrectos en el display Español 2 Deslice la carátula hacia usted y retírela.
Black plate (68,1) Sección 01 Antes de comenzar Modo de demostración de características La demostración de características se inicia automáticamente cuando se apaga la unidad mientras la llave de encendido está en ACC u ON. Al presionar el botón DISPLAY durante la demostración de características, se cancelará este modo de demostración. Vuelva a presionar el botón DISPLAY para iniciar el modo de demostración de características.
Black plate (69,1) Sección Utilización de esta unidad 02 b 12 a c 3 g a 9 8 7 6 Qué es cada cosa Unidad principal 1 Botón SOURCE Esta unidad se enciende al seleccionar una fuente. Presione este botón para visualizar todas las fuentes disponibles. 2 Botón LIST Presione este botón para visualizar la lista de títulos de los discos, la de títulos de las pistas, la de carpetas o la de canales presintonizados, según la fuente de que se trate.
Black plate (70,1) Sección 02 Utilización de esta unidad b Botones VOLUME Presione este botón para aumentar o disminuir el volumen. k Botón AUDIO Presione este botón para seleccionar los diversos controles de calidad del sonido. c Botón FUNCTION Presione este botón para seleccionar las funciones. d Joystick Mueva el joystick para utilizar los controles de sintonización por búsqueda manual, avance rápido, retroceso y búsqueda de pista. También se usa para controlar las funciones.
Black plate (71,1) Sección Utilización de esta unidad Funciones básicas Encendido y apagado Encendido de la unidad % Presione SOURCE para encender la unidad. % Mantenga presionado SOURCE hasta que se apague la unidad. Selección de una fuente Puede seleccionar una fuente que desee escuchar. Para cambiar al reproductor de CD incorporado, cargue un disco en la unidad (consulte la página 74). % Presione SOURCE para seleccionar una fuente.
Black plate (72,1) Sección 02 Utilización de esta unidad Sintonizador Funciones básicas Si se utiliza esta unidad en América del Norte, América Central o América del Sur, se deberá cambiar el paso de sintonía de AM (consulte Ajuste del paso de sintonía de AM en la página 92). 1 2 3 4 5 6 1 Indicador de banda 2 Indicador de estéreo (5) Aparece cuando la frecuencia seleccionada se está transmitiendo en estéreo. 3 Indicador LOC Aparece cuando la sintonización por búsqueda local está activada.
Black plate (73,1) Sección Utilización de esta unidad # Si no se utiliza la lista en unos 30 segundos, el display volverá automáticamente a la visualización normal. Uso del mando a distancia # También se pueden recuperar las frecuencias de las emisoras de radio asignadas a los números de ajuste de presintonías presionando MULTI-CONTROL hacia arriba o abajo durante la visualización de frecuencias. Introducción a las funciones avanzadas 1 Presione MULTI-CONTROL para visualizar el menú principal.
Black plate (74,1) Sección 02 Utilización de esta unidad 1 Utilice MULTI-CONTROL para seleccionar Local en el menú de funciones. Reproductor de CD incorporado 2 Presione MULTI-CONTROL para activar la sintonización por búsqueda local. Funciones básicas # Vuelva a presionar MULTI-CONTROL para desactivar la sintonización por búsqueda local. 3 Presione MULTI-CONTROL izquierda o derecha para ajustar la sensibilidad.
Black plate (75,1) Sección Utilización de esta unidad 1 Presione EJECT para abrir la carátula. Aparece la ranura de carga de discos. Ranura de carga de discos 02 5 Para saltar y retroceder o avanzar hasta otra pista, presione MULTI-CONTROL izquierda o derecha. Notas # Asegúrese de que el lado de la etiqueta del disco esté hacia arriba. # Después de colocar un CD (CD-ROM), presione SOURCE para seleccionar el reproductor de CD incorporado. # Se puede expulsar un CD (CD-ROM) presionando EJECT.
Black plate (76,1) Sección 02 Utilización de esta unidad ! Cuando se reproducen ficheros de audio, puede seleccionar pistas en la carpeta actual. 1 Presione DIRECT. Se visualiza en el display el área para ingresar el número de pista. 2 Presione los botones 0 a 9 para ingresar el número de pista deseada. # Se puede cancelar el número ingresado presionando CLEAR. 3 Presione DIRECT. Se reproducirá la pista seleccionada.
Black plate (77,1) Sección Utilización de esta unidad 02 Pausa de la reproducción de un disco Con la reproducción aleatoria se reproducen las pistas en un orden aleatorio dentro de la gama de repetición seleccionada. Consulte Selección de una gama de repetición de reproducción en la página anterior. 1 Utilice MULTI-CONTROL para seleccionar Pause en el menú de funciones. 1 Utilice MULTI-CONTROL para seleccionar Random mode en el menú de funciones.
Black plate (78,1) Sección 02 Utilización de esta unidad 4 Mantenga presionado MULTI-CONTROL izquierda o derecha para buscar una pista cada 10 pistas en un disco (carpeta). # Si el número de pistas restantes es inferior a 10, mantenga presionado MULTI-CONTROL para recuperar la primera (última) pista. Uso de las funciones de títulos de discos Es posible ingresar títulos de CD y visualizar el título. La próxima vez que se coloque un CD cuyo título se haya ingresado, se visualizará el título de ese CD.
Black plate (79,1) Sección Utilización de esta unidad 1 Presione LIST para cambiar al modo de lista de títulos de las pistas. 2 Utilice MULTI-CONTROL para seleccionar el título de la pista deseada. Haga girar el control para cambiar el título de la pista y presione para seleccionarlo. # También puede cambiar el título de la pista presionando MULTI-CONTROL arriba o abajo. # Si no se utiliza la lista en unos 30 segundos, el display volverá automáticamente a la visualización normal.
Black plate (80,1) Sección 02 Utilización de esta unidad # Si no se utiliza la lista en unos 30 segundos, el display volverá automáticamente a la visualización normal. Reproducción de canciones en el reproductor de audio portátil USB/memoria USB Funciones básicas 1 5 2 3 4 1 Indicador WMA/MP3/AAC Muestra el tipo de fichero que se está reproduciendo actualmente.
Black plate (81,1) Sección Utilización de esta unidad ocho segundos, el modo se cancelará automáticamente. Introducción a las funciones avanzadas 1 Presione MULTI-CONTROL para visualizar el menú principal. FUNCTION, AUDIO y ENTERTAINMENT aparecen en el display. Notas ! Si el reproductor de audio portátil USB tiene una función de carga de la batería y se conecta a esta unidad, la batería se cargará al colocar la llave de encendido del automóvil en la posición ACC u ON.
Black plate (82,1) Sección Utilización de esta unidad 02 2 Presione MULTI-CONTROL repetidamente para seleccionar la gama de repetición. Presione MULTI-CONTROL repetidamente hasta que el ajuste deseado aparezca en el display. ! Track repeat – Sólo repite el fichero actual ! Folder repeat – Repite la carpeta actual ! All repeat – Repite todos los ficheros Notas ! Cuando reproduzca listas de reproducción, se visualizará Playlists.
Black plate (83,1) Sección Utilización de esta unidad Visualización de información de texto de un fichero de audio # Si los caracteres grabados en el fichero de audio no son compatibles con una unidad principal, no aparecerán en el display. # Si determinada información no se grabó en un fichero de audio, no se visualizará el título o el nombre. # Es posible que la información de texto de algunos ficheros de audio no se visualice correctamente.
Black plate (84,1) Sección 02 Utilización de esta unidad Para reproducir canciones en el iPod Puede conectarse y escuchar canciones en un iPod con el conector del Dock o con el interfaz USB. Cuando utiliza un iPod con el conector del Dock, se requiere un conector Dock del iPod para el cable USB. Funciones básicas 1 3 2 1 Indicador del número de canción 2 Indicador del tiempo de reproducción 3 Tiempo de canción (barra de progreso) 1 Presione SOURCE para seleccionar USB.
Black plate (85,1) Sección Utilización de esta unidad 3 Repita el paso 2 para encontrar una canción que desee escuchar. Visualización de información de texto en el iPod % Presione DISPLAY para seleccionar el texto de información deseado.
Black plate (86,1) Sección 02 Utilización de esta unidad 2 Presione MULTI-CONTROL repetidamente para seleccionar la gama de repetición. Presione MULTI-CONTROL repetidamente hasta que el ajuste deseado aparezca en el display.
Black plate (87,1) Sección Utilización de esta unidad Ajustes de audio Introducción a los ajustes de audio 02 # Si no se utilizan las funciones exceptuando 50Hz en unos 30 segundos, el display volverá automáticamente a la visualización normal. Uso del ajuste del balance 1 1 Visualización de audio Muestra el estado de los ajustes de audio. 1 Presione MULTI-CONTROL para visualizar el menú principal. FUNCTION, AUDIO y ENTERTAINMENT aparecen en el display. 2 Utilice MULTI-CONTROL para seleccionar AUDIO.
Black plate (88,1) Sección 02 Utilización de esta unidad Uso del ecualizador El ecualizador le permite ajustar la ecualización de acuerdo con las características acústicas del interior del automóvil. Recuperación de las curvas de ecualización Hay siete tipos de curvas de ecualización memorizadas que se pueden recuperar con facilidad en cualquier momento.
Black plate (89,1) Sección Utilización de esta unidad ! Se puede crear una curva Custom2 común a todas las fuentes. Si se realizan ajustes cuando la curva Custom2 está seleccionada, la curva Custom2 se actualizará. 2 Utilice MULTI-CONTROL para seleccionar el ajuste del ecualizador gráfico de 7 bandas. La frecuencia y el nivel (p. ej., 50Hz +4) aparecen en el display. 3 Presione MULTI-CONTROL izquierda o derecha para seleccionar la banda de ecualización a ajustar.
Black plate (90,1) Sección 02 Utilización de esta unidad 1 Utilice MULTI-CONTROL para seleccionar Sub W.2. # También puede seleccionar el menú de ajustes de subgraves presionando SW en la unidad. # Cuando la salida de subgraves está activada, se puede seleccionar Sub W.2. 2 Presione MULTI-CONTROL izquierda o derecha para seleccionar la frecuencia de corte.
Black plate (91,1) Sección Utilización de esta unidad 2 Utilice MULTI-CONTROL para seleccionar SLA. Notas ! El nivel del volumen del sintonizador de AM también se puede regular con el ajuste del nivel de fuente. ! El reproductor de CD incorporado y el reproductor de CD múltiple se definen automáticamente con el mismo ajuste del nivel de fuente. ! La unidad externa 1 y la unidad externa 2 se definen automáticamente con el mismo ajuste del nivel de fuente.
Black plate (92,1) Sección 02 Utilización de esta unidad # También se puede seleccionar la función presionando FUNCTION en el mando a distancia. # BT AUDIO y Pin code input sólo se pueden seleccionar cuando el adaptador Bluetooth (p. ej., CD-BTB100) está conectado a esta unidad. # Para cancelar los ajustes iniciales, presione BAND. Selección del idioma de visualización Para una mayor comodidad, esta unidad incluye un display en varios idiomas.
Black plate (93,1) Sección Utilización de esta unidad 02 2 Pulse MULTI-CONTROL para seleccionar el paso de sintonía de AM. Al pulsar MULTI-CONTROL repetidamente se cambiará el paso de sintonía de AM entre 9 kHz y 10 kHz. El paso de sintonía de AM seleccionado aparecerá en el display. utilizar equipos auxiliares, consulte Uso de la fuente AUX en la página 96. Cambio del tono de advertencia # Para desactivar la función AUX, vuelva a presionar MULTI-CONTROL.
Black plate (94,1) Sección 02 Utilización de esta unidad Ajuste de la salida posterior y del controlador de subgraves Cambio del silenciamiento/ atenuación del sonido La salida posterior de esta unidad (salida de cables de altavoces traseros y salida RCA posterior) se puede usar para la conexión de altavoces de toda la gama (Rear SP :F.Range) o subgraves (Rear SP :S/W).
Black plate (95,1) Sección Utilización de esta unidad ! También puede activar o desactivar la demostración de características, presionando DISPLAY mientras la unidad está apagada. Para obtener más detalles, consulte Modo de demostración de características en la página 68. 02 Activación de la fuente BT Audio Es necesario activar la fuente BT Audio para utilizar un reproductor de audio Bluetooth. ! Únicamente cuando un adaptador Bluetooth (p. ej.
Black plate (96,1) Sección 02 Utilización de esta unidad 4 Después de ingresar el código PIN (hasta 16 dígitos), presione MULTI-CONTROL. El código PIN que ha ingresado quedará en espera para almacenarse en memoria. Cuando presione de nuevo MULTI-CONTROL en el mismo display, el código PIN que ha introducido se almacenará en esta unidad. # Al presionar MULTI-CONTROL derecha en el display de confirmación, se volverá al display de ingreso de código PIN y se podrá cambiar.
Black plate (97,1) Sección Utilización de esta unidad Selección de AUX como la fuente % Presione SOURCE para seleccionar AUX como la fuente. Presione SOURCE hasta que AUX aparezca en el display. Ajuste del título AUX Se puede cambiar el título que se visualiza para cada fuente AUX1 o AUX2. 1 Después de haber seleccionado AUX como la fuente, utilice MULTI-CONTROL y seleccione FUNCTION para visualizar TitleInput "A".
Black plate (98,1) Sección 02 Utilización de esta unidad % Presione PGM para activar la pausa al seleccionar las siguientes fuentes: ! CD – Reproductor de CD incorporado ! Multi CD – Reproductor de CD múltiple ! USB – Reproductor de audio portátil USB/ memoria USB ! iPod – iPod ! BT Audio – Reproductor de audio Bluetooth ! DVD – Reproductor de DVD/reproductor de DVD múltiple # Para desactivar la pausa, vuelva a presionar PGM.
Black plate (99,1) Sección Accesorios disponibles Para reproducir canciones en el iPod Para escuchar canciones en su iPod Se puede utilizar esta unidad para controlar un adaptador de iPod, que se vende por separado. ! Cuando el iPod está conectado a esta unidad, no se puede encender ni apagar. ! Antes de conectar el conector del Dock de esta unidad al iPod, desconecte los auriculares del iPod.
Black plate (100,1) Sección 03 Accesorios disponibles # Para ir al menú superior de la búsqueda de listas, mantenga presionado MULTI-CONTROL izquierda. # Si no se utiliza la lista en unos 30 segundos, el display volverá automáticamente a la visualización normal. 3 Repita el paso 2 para encontrar una canción que desee escuchar. Visualización de información de texto en el iPod % Presione DISPLAY para seleccionar el texto de información deseado.
Black plate (101,1) Sección Accesorios disponibles Audio Bluetooth Funciones básicas Importante ! Según el reproductor de audio Bluetooth conectado a esta unidad, las operaciones que puede realizar esta unidad se limitan a los dos niveles siguientes: — Nivel inferior: Es posible reproducir únicamente canciones en su reproductor de audio. — Nivel superior: Es posible reproducir, detener, seleccionar canciones, etc. (todas las operaciones descritas en este manual).
Black plate (102,1) Sección 03 Accesorios disponibles 3 Para saltar y retroceder o avanzar hasta otra pista, presione MULTI-CONTROL izquierda o derecha. Introducción a las funciones avanzadas 1 Presione MULTI-CONTROL para visualizar el menú principal. FUNCTION, AUDIO y ENTERTAINMENT aparecen en el display. 2 Utilice MULTI-CONTROL para seleccionar FUNCTION. Haga girar el control para cambiar la opción de menú y presiónelo para seleccionarla. Aparece el nombre de la función en el display.
Black plate (103,1) Sección Accesorios disponibles 2 Presione MULTI-CONTROL para activar la pausa. Se detiene temporalmente la reproducción de la canción actual. # Para desactivar la pausa, vuelva a presionar MULTI-CONTROL. 1 Utilice MULTI-CONTROL para seleccionar Stop en el menú de funciones. 2 Presione MULTI-CONTROL para detener la reproducción. Se detiene la reproducción de la canción actual.
Black plate (104,1) Sección 03 Accesorios disponibles Teléfono Bluetooth Funciones básicas Si utiliza un adaptador Bluetooth (p. ej., CDBTB100), puede conectar a esta unidad un teléfono móvil que posea tecnología inalámbrica Bluetooth para hacer llamadas inalámbricas de manos libres, incluso al conducir. Importante ! Puesto que esta unidad se encuentra en espera si se conecta con sus teléfonos móviles mediante la tecnología inalámbrica Bluetooth sin encender el motor puede descargar la batería.
Black plate (105,1) Sección Accesorios disponibles 03 Realización de una llamada telefónica Antes de poder hacer uso de la función manos libres, deberá configurar la unidad para su utilización con el teléfono móvil. Esto conlleva establecer una conexión inalámbrica Bluetooth entre esta unidad y su teléfono, registrar su teléfono en esta unidad, y ajustar el nivel de volumen.
Black plate (106,1) Sección 03 Accesorios disponibles 2 Presione MULTI-CONTROL abajo para finalizar todas las llamadas. Presione MULTI-CONTROL abajo para finalizar todas las llamadas, incluida una llamada en espera. # La llamada que está atendiendo se pondrá en retención. Para finalizar la llamada, su interlocutor y usted deberán colgar el teléfono. # Mientras las llamadas están retenidas, si presiona MULTI-CONTROL arriba le permitirá alternar entre las llamadas.
Black plate (107,1) Sección Accesorios disponibles Conexión de un teléfono móvil Búsqueda de los teléfonos móviles disponibles 1 Utilice MULTI-CONTROL para seleccionar Search & Connect en el menú de funciones. 2 Presione MULTI-CONTROL para hacer una búsqueda de los teléfonos móviles disponibles. Mientras se realiza la búsqueda, Searching destella.
Black plate (108,1) Sección 03 Accesorios disponibles # A medida que seleccione cada asignación, podrá ver si un teléfono ya está registrado o no. Si la asignación está vacía, se visualizará No data. Si ya se ha adoptado la asignación, aparecerá el nombre del dispositivo. Si desea sustituir una asignación con un nuevo teléfono, primero elimine la asignación actual. Para obtener instrucciones detalladas, consulte Eliminación de un teléfono registrado en esta página.
Black plate (109,1) Sección Accesorios disponibles Uso del Directorio de teléfonos Transferencia de entradas al Directorio de teléfonos 03 Llamada a un número del Directorio de teléfonos Importante Para realizar esta operación debe estacionar su vehículo y poner el freno de mano. 1 Utilice MULTI-CONTROL para seleccionar PH.B.Transfer en el menú de funciones. Una vez encontrado el número al que desea llamar en el Directorio de teléfonos, puede seleccionar la entrada y efectuar la llamada.
Black plate (110,1) Sección 03 Accesorios disponibles Edición del nombre de una entrada del Directorio de teléfonos Importante Para realizar esta operación debe estacionar su vehículo y poner el freno de mano. Importante Para realizar esta operación debe estacionar su vehículo y poner el freno de mano. Puede editar los nombres de las entradas del Directorio de teléfonos. Cada nombre puede tener una longitud de hasta 16 caracteres. Puede editar los números de las entradas del Directorio de teléfonos.
Black plate (111,1) Sección Accesorios disponibles 1 Visualice la lista detallada de su entrada del Directorio de teléfonos deseada. Consulte los pasos 1 al 5 en Llamada a un número del Directorio de teléfonos en la página 109 para el procedimiento. 3 Gire MULTI-CONTROL para cambiar a la pantalla de borrado de memoria.
Black plate (112,1) Sección 03 Accesorios disponibles Es posible asignar a la memoria los números que marca frecuentemente, para volver a marcarlos rápidamente. 4 Cuando haya terminado de ingresar el número, presione MULTI-CONTROL. Se mostrará la confirmación de llamada. 1 Seleccione un número de teléfono del Directorio de teléfonos o del historial de llamadas. O bien ingrese directamente el número de teléfono que desee.
Black plate (113,1) Sección Accesorios disponibles 4 Presione MULTI-CONTROL para borrar la memoria. Se visualiza Cleared y los datos del elemento seleccionado se borran de la memoria de esta unidad. Visualización de la dirección BD (Bluetooth Device) 1 Utilice MULTI-CONTROL para seleccionar Device info en el menú de funciones. El nombre del dispositivo (Pioneer BT Unit) de esta unidad se mostrará en el display. 1 Utilice MULTI-CONTROL para seleccionar Auto answer en el menú de funciones.
Black plate (114,1) Sección 03 Accesorios disponibles Reproductor de CD múltiple Funciones básicas Se puede usar esta unidad para controlar un reproductor de CD múltiple, que se vende por separado. ! Sólo las funciones descritas en este manual son compatibles con los reproductores de CD múltiple de 50 discos. ! Esta unidad no está diseñada para utilizar las funciones de lista de títulos de los discos con un reproductor de CD múltiple de 50 discos.
Black plate (115,1) Sección Accesorios disponibles # También se puede seleccionar la función presionando FUNCTION en el mando a distancia. # Para volver a la visualización de reproducción, presione BAND. # Si no se utilizan las funciones exceptuando ITS memo y TitleInput "A" en unos 30 segundos, el display volverá automáticamente a la visualización normal. Pause Consulte Pausa de la reproducción de un disco en la página 77. Compression Consulte Uso de la compresión y BMX en la página 77.
Black plate (116,1) Sección 03 Accesorios disponibles Uso de listas de reproducción ITS La función ITS (selección instantánea de pista) le permite crear una lista de reproducción de las pistas favoritas incluidas en el cargador del reproductor de CD múltiple. Después de añadir sus pistas favoritas a la lista de reproducción, puede activar la reproducción ITS y reproducir sólo las pistas seleccionadas.
Black plate (117,1) Sección Accesorios disponibles 3 Seleccione la pista deseada presionando MULTI-CONTROL izquierda o derecha. # Si no hay pistas de la lista de reproducción en la gama actual, se visualiza ITS empty y se reanuda la reproducción normal. 5 Presione BAND para volver a la visualización de reproducción. Borrado de un CD de la lista de reproducción ITS Puede borrar todas las pistas de un CD de la lista de reproducción ITS, si la función de reproducción ITS está desactivada.
Black plate (118,1) Sección 03 Accesorios disponibles # Cuando reproduzca un disco CD TEXT, presione MULTI-CONTROL derecha para visualizar una lista de las pistas en el disco seleccionado. Presione MULTI-CONTROL izquierda para volver a la lista del disco. # Si no se ha ingresado un título para un disco, se visualizará No D.Title. # Se visualiza No disc al lado del número del disco cuando no hay discos en el cargador.
Black plate (119,1) Sección Accesorios disponibles 2 Para realizar el avance rápido o retroceso, mantenga presionado MULTI-CONTROL izquierda o derecha. 3 Para saltar y retroceder o avanzar hasta otro capítulo/pista, presione MULTI-CONTROL izquierda o derecha. ! Se puede utilizar esta función sólo si un reproductor de DVD múltiple está conectado a esta unidad. % Presione cualquiera de los botones 1 a 6 para seleccionar el disco deseado.
Black plate (120,1) Sección 03 Accesorios disponibles Nombre de la función Operación Play mode Consulte Selección de una gama de repetición de reproducción en la página 76. Pero la gama de repetición de reproducción que puede seleccionar varía según el tipo de disco o sistema. Las gamas de repetición para la reproducción del reproductor de DVD/reproductor de DVD múltiple son como se indican a continuación: Durante la reproducción PBC de un vídeo CD, no se puede utilizar esta función.
Black plate (121,1) Sección Accesorios disponibles Sintonizador de TV Funciones básicas 1 2 3 1 Indicador de banda 2 Indicador del número de presintonía 3 Indicador de canal 1 Presione SOURCE para seleccionar el sintonizador de TV. 2 Presione BAND para seleccionar una banda. Presione BAND hasta que visualice la banda deseada: TV-1 o TV-2. 3 Para utilizar la sintonización manual, presione MULTI-CONTROL izquierda o derecha.
Black plate (122,1) Sección 03 Accesorios disponibles % Cuando encuentre la emisora que desea almacenar en la memoria, presione uno de los botones de ajuste de presintonías 1 a 6 y manténgalo presionado hasta que el número de presintonía deje de destellar. El número seleccionado destellará en el indicador del número de presintonía y quedará iluminado. La emisora seleccionada se ha almacenado en la memoria.
Black plate (123,1) Apéndice Información adicional Reproductor de audio USB/memoria USB Cuando contacte con su concesionario o con el servicio técnico Pioneer más cercano, asegúrese de anotar el mensaje de error. Mensaje Causa Acción No Audio No hay canciones Transfiera ficheros de audio al reproductor de audio portátil USB/memoria USB y conéctelo. La memoria USB está conectada con la seguridad activada Para desactivar la seguridad, siga las instrucciones de la memoria USB.
Black plate (124,1) Apéndice Información adicional CHECK USB N/A PLAYLIST El conector USB o el cable USB está cortocircuitado. Verifique que no esté enganchado en algo ni dañado el conector USB o el cable USB. El reproductor de audio portátil USB/memoria USB conectado consume más de 500 mA (corriente máxima admisible). Desconecte el reproductor de audio portátil USB/memoria USB y no lo utilice.
Black plate (125,1) Apéndice Información adicional Discos dobles ! Los discos dobles son discos de dos caras que incluyen CD grabable de audio en una cara y DVD grabable de vídeo en la otra cara. ! Debido a que la cara CD de los discos dobles no es físicamente compatible con el estándar CD general, es posible que no se pueda reproducir la cara CD en esta unidad. ! La carga y expulsión frecuente de un disco doble puede producir rayaduras en el disco.
Black plate (126,1) Apéndice Información adicional Reproductor de audio USB/ memoria USB ! No deje el reproductor de audio portátil USB/memoria USB expuesto a la luz solar directa durante un largo periodo de tiempo. La exposición prolongada a la luz solar directa puede causar un fallo de funcionamiento del reproductor de audio portátil USB/memoria USB como consecuencia de la alta temperatura generada. ! No deje el reproductor de audio portátil USB/memoria USB en un lugar con altas temperaturas.
Black plate (127,1) Apéndice Información adicional Compatibilidad con audio comprimido WMA ! Formato compatible: WMA codificado con Windows Media Player Ver. 7, 7.1, 8, 9 o 10 ! Velocidad de grabación: 5 kbps a 384 kbps (CBR), VBR ! Frecuencia de muestreo: 32 kHz, 44,1 kHz, 48 kHz ! Windows Media Audio 9 Professional, Lossless, Voice: No MP3 ! Formato compatible: MPEG-1, 2, 2.
Black plate (128,1) Apéndice Información adicional ! Se pueden visualizar sólo 64 caracteres desde el principio como nombre de fichero (incluida la extensión, como .wma, .mp3, .m4a o .wav) o nombre de carpeta. ! La secuencia de selección de carpetas u otras operaciones pueden cambiar, dependiendo del código de codificación o escritura.
Black plate (129,1) Apéndice Información adicional Especificaciones Generales Audio Potencia de salida máxima ..................................................... 50 W × 4 50 W × 2/4 W + 70 W × 1/2 W (para altavoz de subgraves) Potencia de salida continua ..................................................... 22 W × 4 (50 Hz a 15 000 Hz, 5% THD, 4 W de carga, ambos canales activados) Impedancia de carga ............. 4 W a 8 W × 4 4Wa8W×2+2W×1 Nivel de salida máx.
Black plate (130,1) 130 Es 130
Black plate (131,1) Español Es 131 131
Black plate (132,1) PIONEER CORPORATION 4-1, MEGURO 1-CHOME, MEGURO-KU TOKYO 153-8654, JAPAN PIONEER ELECTRONICS (USA) INC. P.O. Box 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: (0) 3/570.05.11 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555 PIONEER ELECTRONICS AUSTRALIA PTY. LTD.