Owner manual

Thank you for buying this PIONEER product.
Please read through these operating instructions so you will
know how to operate your model properly. After you have
finished reading the instructions, put them away in a safe
place for future reference.
In some countries or regions, the shape of the power plug
and power outlet may sometimes differ from that shown in
the explanatory drawings. However, the method of
connecting and operating the unit is the same.
WARNING : TO PREVENT FIRE OR SHOCK HAZARD,DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
This product complies with the Low voltage Directive (73/23/
EEC), EMC Directives (89/336/EEC, 92/31/EEC) and CE Marking
Directive (93/68/EEC).
THE POWER SWITCH IS SECONDARY CONNECTED AND
THEREFORE DOES NOT SEPARATE THE UNIT FROM MAINS
POWER IN STANDBY POSITION.
IMPORTANT
A
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SER
VICE PERSONNEL.
A
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
IMPORTANT
FOR USE IN THE UNITED
KINGDOM
The wires in this mains lead are coloured in
accordance with the following code :
blue: neutral
brown: live
If the plug provided is unsuitable for your socket outlets, the
plug must be cut off and a suitable plug fitted.
The cut-off plug should be disposed of and must not be
inserted into any 13 amp socket as this can result in electric
shock. The plug or adaptor or the distribution panel should be
provided with 5 amp fuse. As the colours of the wires in the
mains lead of this appliance may not correspond with coloured
markings identifying the terminals in your plug, proceed as
follows :
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected
to the terminal which is marked with the letter L or coloured
red.
Do not connect either wire to the earth terminal of a
three pin plug.
NOTE
After replacing or changing a fuse, the fuse cover in the plug
must be replaced with a fuse cover which corresponds to the
colour of the insert in the base of the plug or the word that
is embossed on the base of the plug, and the appliance must
not be used without a fuse cover. If lost, replacement fuse
covers can be obtained from your dealer.
Only 5 A fuses approved by B.S.I. or A.S.T.A. to B.S.
1362 should be used.
Location
Power-cord Caution
Install the tuner in a well-ventilated location where it
will not be exposed to high temperatures or humidity.
Do not install the tuner in a location which is exposed to direct rays
of the sun, or near hot appliances or radiators. Excessive heat can
adversely affect the cabinet and internal components. Installation
of the tuner in a damp or dusty environment may result in a
malfunction or accident. (Also avoid installation near cookers, etc.,
where the tuner may be exposed to smoke, steam, or heat.)
Condensation
When this unit is brought into a warm room from previously cold
surroundings or when the room temperature rises
sharply,condensation may from inside,and the unit may not be able
to attain its full performance. In this case, allow the unit to stand for
about an hour or raise the room temperature gradually.
Handle the power cord by the plug. Do not pull out the plug by
tugging the cord and never touch the power cord when your hands
are wet as this could cause a short circuit or electric shock. Do not
place the unit, a piece of furniture, etc., on the power cord, or pinch
the cord. Never make a knot in the cord or tie it with other cords.
The power cords should be routed such that they are not likely to
be stepped on. A damaged power cord can cause fire or give you
an electrical shock. Check the power cord once in a while. When
you find it damaged, ask your nearest PIONEER authorized service
center or your dealer for a replacement.
Maintenance of External Surfaces
• Use a polishing cloth or dry cloth to wipe off dust and dirt.
• When the surfaces are very dirty, wipe with a soft cloth dipped
in some neutral cleanser diluted five or six times with water,
and wrung out well, and then wipe again with a dry cloth. Do
not use furniture wax or cleaners.
• Never use thinners, benzine, insecticide sprays or other chemi
cals on or near this unit, since these will corrode the surfaces.