Owner's Manual

<A1-000036-9L-A> 15 <A1-000036-9L-A> 16<A1-000036-9L-A> 13 <A1-000036-9L-A> 14
En En
4 Attach the top panel cover and Badge.
Use the removed screws to attach the top
panel cover (fastening torque 0.6 to 0.8
N·m).
Remove the release paper and affix the
Badge in the orientation shown in the
following illustration.
1
2
3
1 Screws
2 Badge
3 Top panel cover
Additional information
Specications
Power source ...................... 14.4 V DC (10.8 V to 15.1 V
allowable)
Grounding system .............. Negative type
Current consumption ......... 41 A (at continuous power,
4 W,
Normal mode)
56 A (at continuous power,
4 W,
High power mode)
Average current consumption
.......................................... 9.3 A (4 W for six channels,
Normal mode)
12.5 A (4 W
for six channels,
High power mode)
14.5 A (2 W
for six channels,
Normal mode)
16.7 A (2 W
for six channels,
High power mode)
Fu
se ..................................... 40 A × 2
Dimensions (W × H × D) ..
260 mm × 50.6 mm × 180 mm
(10-1/4 in. × 2 in. × 7-1/8 in.)
Weight ................................. 2.6 kg (5.7 lbs)
(Leads for wiring not
in
cluded)
Continuous power output .. 75 W × 6 (at 14.4 V, 4 W,
20 Hz to 20 kHz, ≤ 1 % THD,
No
rmal mode)
100 W × 6 (at 14.4 V, 2 W,
1 kHz, ≤ 1 % THD, Normal
m
ode)
150 W × 3 (at 14.4 V, 4 W,
MONO, 1 kHz, ≤ 1 % THD,
No
rmal mode)
100 W × 6 (at 14.4 V, 4 W,
20 Hz to 20 kHz, ≤ 1 % THD,
Hi
gh power mode)
100 W × 6 (at 14.4 V, 2 W,
1 kHz, ≤ 1 % THD, High
p
ower mode)
200 W × 3 (at 14.4 V, 4 W,
MONO, 1 kHz, ≤ 1 % THD,
Hi
gh power mode)
Load impedance ................. 4 W (2 W to 8 W allowable)
Frequency response ...............10 Hz to 50 kHz (+0 dB, –3 dB)
Signal-to-noise ratio ........... 95 dB (IHF-A network)
Distortion ............................ 0.05 % (10 W, 1 kHz)
Low pass filter:
Cut off frequency ........ 50 Hz to 500 Hz
Cut off slope ................ –12 dB/oct
High pass filter:
Cut off frequency ........ 50 Hz to 500 Hz
Cut off slope ................ –12 dB/oct
Gain control:
RCA .............................. 0.2 V to 6.5 V
Speaker ........................ 0.8 V to 16 V
Maximum input level / impedance:
RCA .............................. 6.5 V / 25 kW
Speaker ........................ 16 V / 12 kW
CTA2006 Specications
Power output....................... 75 W RMS × 6 Channels (at
14.4 V, 4 W, 20 Hz to 20 kHz
and ≤ 1 % THD+N, Normal
mode)
100 W RMS × 6 Channels
(
at 14.4 V, 4 W, 20 Hz to 20
kHz and ≤ 1 % THD+N,
High power mode)
S/N ratio ............................... 75 dBA (reference: 1 W into
4 W)
Accessories
Speaker line input RCA cable × 3
Hexagonal wrench × 1
Mounting screw (4 × 25 mm) × 4
Logo Badge× 1
Fuse cover × 1
Cover for RCA Terminal × 6
Notes
 Specifications and design are subject to mod-
ification without notice.
 The average current consumption is nearly
the maximum current consumption by this
unit when an audio signal is input. Use this
value when working out total current con-
sumption by multiple power amplifiers.
 Install tapping screws in such a way that the
screw tip does not touch any wire. This is
important to prevent wires from being cut by
vibration of the boat, which can result in fire.
 Make sure that wires do not get caught in
the sliding mechanism or touch the legs of a
person in the boat as short-circuit may result.
CAUTION
 Place all cables away from hot places, such
as near the heater outlet.
 The optimal installation location differs
depending on the boat model. Secure the
amplifier at a sufficiently rigid location.
 Check all connections and systems before
final installation.
Example of installation on
the chassis
1 Place the amplier in the desired
installation location.
Insert the supplied tapping screws (4 mm
× 25 mm) into the screw holes and push
on the screws with a screwdriver so they
make an imprint where the installation
holes are to be located.
2 Drill 2.5 mm (1/8 in.) diameter holes in
the chassis.
3 Install the amplier with the use of
supplied tapping screws (4 mm × 25
mm).
1
5
3
4
2
1 Tapping-screws (4 mm × 25 mm)
2 Installation surface
3 Hole-to-hole distance: 228.3 mm (9 in.)
4 Hole-to-hole distance: 160.8 mm (6-11/32 in.)
5 Hole-to-hole distance: 226 mm (8-29/32 in.)