ORDER NO. ARP3051 PROJECTION MONITOR RECEIVER PRO-610HD PRO-510HD SD-582HD5 SD-532HD5 THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). Model Type Power Requirement Remarks PRO-610HD PRO-510HD SD-582HD5 SD-532HD5 KUXC/CA KBXC AC120V –– –– –– AC120V This service manual should be used together with the following manual(s): Model No. Order No. PRO-610HD ARP3047 Remarks CONTENTS 6. ADJUSTMENT ................................................ 195 7. GENERAL INFORMATION ...........
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 194
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6. ADJUSTMENT 6.1 INTRODUCTION • IMPORTANT When replacement of the following assemblies are required during repairs, be sure to replace the EEPROMs with the mounted ones in order to retain the adjustment data of the unit and to facilitate adjustment after the replacement of the assemblies. Name of Assy SIGNAL Assy EEPROM IC2454 [24LC32(I)P] DIGITAL CONV.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6.3 ADJUSTMENT LOCATION AND ITEMS Assembly Adjustment Location Focus VR (VR1) B G Focus VR R Front View Lens assy (For Green) Lens assy Lens assy (For Blue) (For Red) B CONV. AMP ASSY C DIGITAL CONV.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Assembly Adjustment Location Guide If POWER SUPPLY ASSY is repaired or replaced No adjustment is required If DEFLECTION SERVICE ASSY is repaired or replaced 1 3 5 6 7 If CONV.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6.4 FACTORY ADJ MODE Start Factory Adjustment Mode 1st FAC Select 1st FACTORY ADJ Mode Select 1st FACTORY ADJ mode, then adjust. Selecting the mode for adjustment operations. Start Normal picture Front panel TV TV/ CBL VCR DVD DTV /SAT /LD TV Start adjusting ON/OFF TV POWER DTV INPUT 1 2 3 SPLIT SEARCH SELECT ANT FREEZE 4 SCREEN SUB CH MODE DTV AUDIO POWER The 2nd FACTORY ADJ mode is not used in the adjustment.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 1 OTHER OFFSET mode To enter the OFFSET mode of each picture quality, use the following keys and codes of the remote control unit: A C D B V L T 2 STD OFFSET MODE COMP (15 kHz) OFFSET MODE COMP (31 kHz, 33 kHz) OFFSET MODE TV OFFSET MODE COLOR TEMP B&W for STD COLOR TEMP FILM for STD & GAME RGB OFFSET MODE Key(s) on the Remote Control Unit DOWN P in P CH-, SUB CHP in P CH+, SUB CH+ RED DTV MENU INFO CH ENTER The screen size modes change cyclically with each p
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 2 Deflection Yoke Adjustment 2 -1 Deflection Yoke Lean Adjustment Start • Input a stable signal (e.g. from an LD player or SG) to the INPUT 1 connector. • MENU → SETUP → Enter the MULTI-POINT (FULL) in the CONVERGENCE. • The cross hatch disappears if there is no operation with the remote control unit for about 8 minutes. If the cross hatch disappears, repeat the above operation with the remote control unit.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 3 Focus Adjustment 3 -1 Focus Adjustment of Lens Assy Start Cross hatch Lens assy (For Green) Lens assy Lens assy (For Red) (For Blue) "Best focusing" 3 -2 Focus VR Adjustment Cross hatch Focus VR (VR1) B G R FOCUS VR Turn the Focus VR for best focusing.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 4 Test-cross Position Check • Check the test-cross position. If it is located within ± 20 mm from the center of the screen, no adjustment is required. If it is not, adjust the position as follows: • Input a stable NTSC (480i) signal (e.g. from an LD player) and adjust the position.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 5 Screen Size Adjustment Check if both vertical and horizontal sizes are within 91% ±2%.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Note : Screen mode : FULL 5 -3 Horizontal Size Adjustment Start Note : • After the V. SIZE adjustment, enter the H. SIZE adjustment by pressing "1" key. • After the H. SIZE adjustment, check that V. SIZE is 91± 2%. If not, readjust the V. SIZE. 1st FAC INPUT 1:Monoscope Green screen ANT 1 H.SIZE 91% ± 2% or INPUT TV General broadcasting VOL Adjust the size so that the picture is completely displayed on the screen.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6 CONVERGENCE ADJUSTMENT 1. Procedures 1. When replacinf the DIGITAL CONV. Assy, replace the EEPROM of new DIGITAL CONV. Assy with the EEPROM of old DIGITAL CONV. Assy. 2. Check the initial data for the convergence adjustment. 3. Perform the coarse adjustment for the green to roughly correct distortion of the green. 4. Fine-adjust the green to eliminate any distortion. The green becomes the standard for the red and the blue. If necessary, repeat steps 3 and 4.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Table 2 OFFSET CONVER DATA OFFSET CONVER MODE 1 Numeric Adjustment Key Item 1 2 3 DFH DFV HDP Screen Mode F Z C N H FULL ZOOM CINEMA NATURAL HD FULL 0F0 070 010 0D0 070 010 0D0 070 010 0D0 070 010 The cross-hatch signal is generated inside the unit, and is automatically displayed in OFFSET CONVER. mode and MANUAL CONVERGENCE mode. You can turn on and off the cross-hatch signal with the YELLOW key.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 • Pattern for each adjustment item Key No. ` STATIC Key No. 1 Key No. 8 SKEW SIZE = Fixed position GH Key No. ` Key No. 1 STATIC SKEW Key No. 6 Key No. 8 PIN SIZE GV Note 1: When the green CRT is replaced, or when the deflection yoke for the green is replaced, prior to the convergence adjustment, tune the center of the image to the center of the screen by turning the centering magnet. Note 2: When the CONVER. AMP Assy or DIGITAL CONV.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 3.4.3 3.4.4 Press the SET/ENTER key when the point to be adjusted is determined. When adjustment of the selected point is finished, press the SET/ENTER key, then adjust the other adjustment points by repeating 3.4.1 to 3.4.4. Screen indication 3.4.5 Make the adjustment for the green in each screen mode, and use the green as the standard screen for the red and the blue. To change screen modes, use the SCREEN mode key.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 4th step In a case of an error in convergence: Repeat 2nd and 3rd steps to take total balance. Then the adjustment for the green is completed. To return from the fine adjustment mode to the coarse adjustment mode, press the MENU key once, then the DOT key. Adjustable points Good adjustment: 5 20 2 Adjustment data -5 30 -3 Adjustment data Note: When the MENU key is pressed to quit MANUAL CONVERGENCE mode, the display will be unstable for several seconds.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 • Pattern for each adjustment item Key No. ` STATIC Key No. 1 Key No. 7 Key No. 8 SKEW LIN SIZE Key No. 1 Key No. 4 Key No. 6 RH BH Key No. ` STATIC SKEW KEY PIN RV BV Key No. 8 SIZE = Fixed position Note 1: When the red CRT is replaced, or when the deflection yoke for the red is replaced, prior to adjustment, tune the center of the image to the center of the screen by turning the centering magnet. Note 2: When the CONVER.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 3.6.5 Repeat procedures 3.6.2 through 3.6.4 for the other screen modes. (Completion of the red adjustment) 3.7 Coarse Adjustment and Fine Adjustment of the Blue Make coarse and fine-adjustments of the blue in the same manner as with the red, described in 3.5 and 3.6. 3.8 Confirmation of Adjustment After the green, red, and blue adjustments are finished, check convergence errors with the patterns for all three colors on the monitor.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 7 -2 White Balance Adjustment Start This mode is to set the standard picture quality for a normal picture.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Adjustment Procedure of White Balnce OFFSET Data Table COLOR TEMP Setting STD I Without RGB Input RGB Input NEWS LIVE FILM STD FILM MOVIE B&W STD B&W MOVIE NEWS LIVE FILM B&W J K L M V X β γ Y Z MOVIE E TV B User Mode Input Signal COMPORNENT 15K C GAME F COMPORNENT 31K 33K D STD OFFSET A RGB T Adjustments are required for A, C, D, T, L, and V in the table above. Data in other parts are fixed.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 DIRECT KEY OFFSET MODE OFFSET DATA (VIDEO) ADJ :Adjustment item The numerical value is shipping a set value in the factory. A set value is data of 1999.11 present provinces. DIRECT KEY OFFSET MODE KEY ADJ NAME MODEL PRO-610HD SD-582HD5 PRO-510HD SD-532HD5 DOWN STD OFFSET A 1 COLOR 2 TINT 3 CONTRAST 4 BRIGHT 5 SHARPNESS 6 DETAIL 7 S. V.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 8 Panel Adjustment Start • Mode for adjusting the brightness, contrast LEFT and RIGHT of the gray part (panel) of the 4:3 normal screen.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Size Adjustment of the Panel Part of the 4:3 Normal Screen "Monoscope signal" Set the LEFT data item to 91 ± 2%. 3 9 4 Panel Adjustment for DTV (PRO-610HD, PRO-510HD ONLY) Start 1st FAC • Mode for adjusting the brightness, contrast LEFT and RIGHT of the gray part (panel) of the 4:3 normal screen of the DTV tuner. TV/ CBL VCR DVD DTV /SAT /LD TV Set the RIGHT data item to 91 ± 2%.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 218
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 7. GENERAL INFORMATION 7.1 DIAGNOSIS 7.1.1 DIAGNOSIS METHOD How to diagnose a failure Various protection circuits are provided for this unit. When these protection circuits are activated, the power of the unit is shut down (P.D.: Power Down). The defective parts can be easily diagnosed by observing the LEDs inside the following assemblies. 1. POWER SUPPLY Assy For models PRO-610HD/510HD : D915 in the AWV1795 For models SD-582HD5/532HD5 : D915 in the AWV1808 2.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 1. P.D. (1) Failure in the POWER SUPPLY Assy and the AUDIO Assy. There are four main possibilities: 1. Abnormality in the regulator of the heater 2. Blown fuse(s) in secondary 3. Abnormality in RELAY (RY102) 4.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Note: The anode of the diode is high only for a short time after the power is turned on until the protection circuits are activated (P.D.) The LEDs are lit by the HOLD circuit. Note that the power may be shut down when the voltages 130 V, 25 V, and 12 V from the POWER SUPPLY Assy are not supplied because the DEFLECTION SERVICE Assy is powered by the POWER SUPPLY Assy. When overload detection mechanisms 1 and 2 are activated, the 130 V line is short-circuited.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 4.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 L DEFLECTION SERVICE ASSY (AWV1809) D321 D923 K CONV.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 7.1.2 DISASSEMBLY How to remove the screen (for adjusting Lens assemblies) Screen Frame 1 2 1 4 Loosen a screw 5 Remove a screw Screen Side Fitting Loosen two screws Remove Upper Cabinet Metal Upper Cabinet Metal Screen Side Fitting 3 ∗ For SD-582HD5 and SD-532HD5 3 3 3 Note∗: Screen side Fitting comes off even if this screw is not removed. However, remove this screw. When the screen is done in the slide, the screen is damaged with this screw.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Lens Assy (Red) Lens Assy (Green) Lens Assy (Blue) Slide the screen to right, and adjust the focus of the lens. Notes: To assemble the screen, perform the above procedures in reverse order. After assembling it, verify that the right and left sides of the screen are positioned as shown in the figure. Fit left side edge of the screen to center of cabinet hole.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 7.1.3 WIRING DIAGRAM Front Section Focus VR (VR1) CRT Assy (R) R. CRT DRIVE Assy FBT Focus Wire At least 15 mm away from any other parts. Binder Focus VR Binder 226 CRT Assy (G) G. CRT DRIVE Assy CRT Assy (B) B.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Rear Section Loop with a radius of 30mm or more. Ferrite Core At least 15mm away from any other parts. Loop with a radius of 50mm or more. FBT CONV.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 7.2 IC • The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 • Pin Function No. Pin Name I/O 1 DVDD − 2 DVDD − 3 B0 Pin Function Digital power supply +5V or +3.3V No.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 MB40958PFQ (SUB VIDEO SERVICE ASSY : IC3602) (PRO-610HD, PRO-510HD ONLY) • D/A Converter • Block Diagram CLKR 1 46 ROUT (MSB) R1 4 R2 5 R3 6 R4 7 R5 8 Input Buffer 8 Master 8 Slave F•F Buffer 8 Current SW R6 9 R7 10 (LSB) R8 11 VCCA CLKG 2 43 GOUT (MSB) G1 14 G2 15 G3 16 G4 17 G5 18 Input Buffer 8 Master 8 Slave F•F Buffer 8 Current SW G6 19 G7 20 (LSB) G8 21 VCCA CLKB 3 40 BOUT (MSB) B1 24 B2 25 B3 26 B4 27 B5 28 Input Buffer 8 Master 8 Sla
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 • Pin Function No. Pin Name 1 CLKR I/ O I Pin Function R ch clock signal input 2 CLKG I G ch clock signal input 3 CLKB I B ch clock signal input I R ch data signal input (R1: MSB, R8: LSB) − Non connection I G ch data signal input (G1: MSB, G8: LSB) − Non connection I B ch data signal input (B1: MSB, B8: LSB) − Non connection 4 R1 5 R2 6 R3 7 R4 8 R5 9 R6 10 R 7 11 R 8 12 N.C. 13 N.C.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 CXA3106Q (SUB VIDEO SERVICE ASSY : IC3201) (PRO-610HD, PRO-510HD ONLY) • PLL IC • Pin Function No. Pin Name I/O Pin Function No.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 PE5066A (SUB VIDEO SERVICE ASSY : IC3401) (PRO-610HD, PRO-510HD ONLY) • I/P System Controller IC • Pin Function No. Pin Name I/O Pin Function No.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 No. Pin Name I/O Pin Function No. Pin Name 91 UD(4) 141 MDY(23) 92 UD(3) 142 MDY(22) 93 UD(2) I/O Data input/output for PE5066A 94 UD(1) 143 MDY(21) 145 MDY(19) − Ground 97 MDC(23) 98 MDC(22) 146 MDY(18) 147 MDY(17) I/O Data input/output for external SGRAM 99 MDC(21) 148 MDY(16) 149 MDY(7) 100 VDD − Power supply (3.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 No. Pin Name I/O Pin Function No. Pin Name 191 NC 216 YI(3) 192 NC 217 YI(2) 193 NC 218 YI(1) 194 NC 195 NC I/O I Non connection 196 NC 220 VDD − Power supply (3.3V) 221 GND − Ground 197 NC 222 PBI(7) 198 NC 223 PBI(6) 199 NC Digital input of Y signal (lower bit) 219 YI(0) − Pin Function (upper bit) 224 PBI(5) 200 GND − Ground 225 PBI(4) 201 VDD − Power supply (3.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 PE5067A (SUB VIDEO SERVICE ASSY : IC3501) (PRO-610HD, PRO-510HD ONLY) • I/P System Controller IC • Pin Function No. Pin Name I/O Pin Function No. Pin Name I/O Pin Function 1 GND − Ground 51 DEI I Data enable input for external DIGITAL I/F 2 GN D − Ground 52 HDI I H. sync signal input 3 CLK I System clock input 53 VDI I V.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 No. Pin Name I/O Pin Function 101 BAO(6) 102 BAO(5) O Demultiplex digital outut A of B/PB signal 103 BAO(4) No. Pin Name − 153 GND − 154 GND − O 104 VDD − Power supply (3.3V) 155 GBO(0) 105 GND − Ground 156 RBO(7) 106 BAO(3) 107 BAO(2) I/O 152 VDD Pin Function Power supply (3.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 No. Pin Name I/O Pin Function 203 PBP(10) 206 PBP(13) I/O 254 YI(5) 204 PBP(11) 205 PBP(12) No. Pin Name 255 YI(6) I Digital input of B-Y signal after sequential converted O 256 YI(7) (upper bit) 258 NC 208 PBP(15) (upper bit) 259 NC 209 VDD − Power supply (3.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 EM636327Q-8 (SUB VIDEO SERVICE ASSY : IC3601, IC3604) (PRO-610HD, PRO-510HD ONLY) • 16M SGRAM • Pin Function No. Pin Name 1 DQ 3 2 VDDQ 3 DQ4 4 DQ5 5 VSSQ 6 DQ6 7 DQ7 8 VDDQ 9 DQ16 10 DQ17 11 VSSQ 12 DQ18 I/O Pin Function No.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 PD3420A8 (SUB VIDEO SERVICE ASSY : IC3801) (PRO-610HD, PRO-510HD ONLY) • I/P System micro-computer IC • Pin Function No. 1 Pin Name VCC I/O − 2 CS7 O 3 CS6 O 4 CS5 O Pin Function No.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 SAA4990H (SUB VIDEO ASSY : IC3401) (SD-582HD5, SD-532HD5 ONLY) • Progressive scan-Zoom and Noise Reduction IC (PROZONIC) • Pin Function No. Pin Name 1 TEST1/AP I/O I Pin Function Action pin for testing, to be connected to Vss. No. Pin Name 41 HD I/O I Pin Function Horizontal reference signal 2 TEST2/SP I Shift pin for testing, to be connected to Vss.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 CD74HCT4046AM (SUB VIDEO ASSY : IC3402) (SD-582HD5, SD-532HD5 ONLY) • PLL IC • Pin Function No. Pin Name I/O Pin Function No.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 SAA4977H-K (SUB VIDEO ASSY : IC3403) (SD-582HD5, SD-532HD5 ONLY) • BESIC (A/D, D/A Memory Control IC) • Pin Function No. Pin Name Pin Function No. Pin Name Pin Function 1 SDA I2C-bus serial data (port 1.7) 2 SCL I2C-bus serial data (port 1.6) 42 YOD4 Y digital output bit 4 3 P1.5 Port 1 data input/output signal 5 43 YOD5 Y digital output bit 5 41 YOD3 Y digital output bit 3 4 P1.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 24LC128(I)P (DIGITAL CONV. ASSY : IC1410) • 128Kbit CMOS Serial EEPROM Pin Assignment (Top view) A0 1 8 VCC A1 2 7 WP A2 3 6 SCL VSS 4 5 SDA Block Diagram A0 A1 A2 WP 1 2 3 7 HV GENERATOR SCL 6 I/O CONTROL LOGIC SDA 5 I/O MEMORY CONTROL LOGIC XDEC EEPROM ARRAY PAGE LATCHES Pin Function No.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 CM0006CF (DIGITAL CONV. ASSY : IC1401) • Digital Convergence Correction IC • Pin Function No.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 No.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 24LC32A(I)P (SIGNAL ASSY : IC2454) • 32Kbit CMOS Serial EEPROM Pin Assignment (Top view) A0 1 8 VCC A1 2 7 WP A2 3 6 SCL VSS 4 5 SDA Block Diagram A0 A1 A2 WP 1 2 3 7 HV GENERATOR SCL 6 I/O CONTROL LOGIC SDA 5 I/O MEMORY CONTROL LOGIC EEPROM ARRAY XDEC PAGE LATCHES Pin Function No.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 CXA2094Q (SIGNAL ASSY : IC2701) • US Audio Multi-channel Decoder IC SOUT 47 46 ESAPIN 45 44 TVOUT-S TVOUT-R TVOUT-L AUX2-R AUX2-L • Block Diagram 40 39 38 FEXT2 AUX1-R 41 LPF TVSW AUX1-L 42 36 VCATC FEXT1 MAININ 3 VCA TVSW/EXT/M1 RMSDET 37 VCAWGT 35 VCAIN MATRIX 34 VEOUT 33 VETC RMSDET VE NRSW/FOMO/SAPC SPECTRAL VCA LPF LPF LPF DeEm LPF LPF LOGIC DeEm AMP (+4dB) 23 STIN SW 27 SAPIN (+6dB) SUBOUT 22 WIDEBAND MAINOUT 4 LPF 28
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 • Pin Function No.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 CM0010AF (SIGNAL ASSY : IC7703) • Multi Screen Controller IC • Pin Function (1) A/D Inputs for Main Video Signals No. 62 Pin Name MYIN I/ O I Pin Function Main video Y luminance input signal. Typical input level is 1.7Vp-p. 56 MYVREFH I/O ADC top reference voltage for main Y signal. Maximum value (2.726V in typical) of ADC dynamic range is set by self-bias. 64 MYVREFL I/O ADC bottom reference voltage for main Y signal. Minimum value (0.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 (3) Main PLL No. 120 Pin Name I/ O Pin Function MHS I Main horizontal synchronous input, it inputs NTSC 15.75Hz signal. 121 MCPOUT1 O Charge pump output, it connects to MVCOIN1 pin through external loop filter. 122 MVCOIN1 I VCO voltage input 123 MLPFGND − Ground for the external loop filter 125 MPLLVDD1 − Power supply voltage for PLL, it connects to digital power supply voltage.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 (6) DRAM No. Pin Name I/ O Pin Function 144-145, 147-149, ADD [8:0] 151,152, 156,157 O 9 bit DRAM address bus 2-4,158, 160,161, 163-165, DAT [15:0] 167,168, 170-172, 175,176 I/O 16 bit DRAM data bus 139 NRAS O Row address strobe output signal 140 NCAS O Column address strobe output signal 141 NWE O Write enable output signal 142 NOE O Output enable signal (7) I 2C Bus No.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 (10) Others No. 134 Pin Name NRST I/ O Pin Function I System reset input signal 5,86,87, 105,132, 133,143, SYSVDD 150,159, 166,173, 174 − 3.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 7.3 EXPLANATION CONNECTING VIDEO/AUDION EQUIPMENT Front panel S-VIDEO VIDEO L-AUDIO-R (MONO) R L VIDEO S-VIDEO OUTPUT INPUT 4 V L R R L V Video movie/VCR INPUT jacks COMPONENT VIDEO INPUT jack There are 4 sets of inputs for VCR and DVD/LD players. Use RCA-type pin plug cords (the same as those used in Hi-Fi systems) for connections. When the audio source to be connected is monaural, connect the source to the L-(MONO) jack.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 SIGNAL NOTE: Setting the INPUT 3 SELECT switch to ‘RGB’ will cause all S-Video and composite images input from the INPUT 3 jack to be suppressed. Similarly, setting the INPUT 3 SELECT switch to ‘SVIDEO/VIDEO’ will cause all images input from the RGB input jack to be suppressed. Rear panel SIGNAL Digital tuner TO WATCH TV To turn off the sound Press the MUTING button.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 PROGRAM BLOCK (V. CHIP) FUNCTION Since laws have been passed in the United States requiring a way of blocking undesirable programming, the V-chip has become a required component in television sets. The V-chip is a computer chip which decodes signals added to broadcast signals transmitted by television broadcasters. These signals are classified by programming content (e.g.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 SETTING THE PROGRAM BLOCKING LEVEL 1 Press MENU and select SET UP by using the 5 or ∞ button and then pressing SET/ENTER. 2 Select PROGRAM BLOCK in the same way. SET/ ENTER 3 Enter password. • • • 4 Press numeric buttons ‘0’ through ‘9’ to enter a four-digit password. If the password has not been changed as described in Changing Password, enter the default password of ‘1234’. If you wish to change the password, see p.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 5 Set BLOCK to ON. SET/ ENTER 6 Select MPAA RATING or TV PARENTAL GUIDELINES . SET/ ENTER 7 Select and then confirm the rank of the MPAA RATING. SET/ ENTER SET/ ENTER 8 NOTE: • Blocking programming with a low rating will cause all programming with a higher rating also to be blocked. • The ‘NR’ (not rated) of the MPAA RATING may be set to ‘View’ or ‘Block’ without regarded to other ratings. Select and confirm the rank of the TV PARENTAL GUIDELINES.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 9 HOW TO REMOVE BLOCKING FROM A PROGRAM IN PROGRESS When a selected program or a program on a channel to which you have just changed has a rating higher than the current program blocking rating, the picture and sound will cut off and an enter password screen will appear. After setting, press MENU to turn the menu off.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 MULTI-SCREEN FUNCTION VIEWING TWO SCREENS (SPLIT screen) The screen can be split vertically, making it possible to view different images on the left and right. Press the SPLIT button. (Main picture) • • • • NOTES: • The same image cannot be viewed as both the main picture and the sub-picture. • Pressing the MENU button in SPLIT or FREEZE screen mode restores the screen display to normal and displays the menu on screen.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 SEARCHING FOR A PROGRAM ON A DIFFERENT CHANNEL (SEARCH screen) The screen on the right side can be made into nine or three different screens, making it possible to search for programs or enjoy multiple images. Press the SEARCH button. • Each time the SEARCH button is pressed, the screen mode changes in the following order.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 MULTI-SCREEN FUNCTION Convergence adjustment may be fined-tuned from here. 1 Press MENU and select SET UP by using the 5 or ∞ button and then pressing SET/ENTER. 2 Adjust the center point convergence. 3 Select ADJ MULTI-POINT . SET/ ENTER 4 Select the adjust point. SET/ ENTER 5 NOTES: • The number of adjustment points varies according to the screen mode. The cursor is partially invisible around the edge of the screen according to the screen mode.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6 Adjust the blue line. SET/ ENTER • 7 The brackets which shows the adjusting point will move in order. Move to the next point to be adjusted, and repeat steps 4 to 6. After completing the convergence adjustment, press MENU to turn the menu off.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 SPECIAL NOTES Picture Adjustments MOVIE or GAME mode may not be selected when receiving RGB input. GAME mode setting: • All signals output from the Projection Monitor will be unaffected. Only the original output signal is sent through the output jacks. Picture Quality setting: • The COLOR, TINT, and SHARP settings may not be changed when receiving RGB input. • When DPO is on, CONTRAST, BLACK LEVEL and COLOR cannot be adjusted.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 265
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 8. PANEL FACILITIES AND SPECIFICATIONS PANEL FACILITIES for PRO-610HD and PRO-510HD A flip-down door conceals the control panel. Push gently and release, to open the door. To close the door, lift it back up into place. 1 POWER STANDBY/ON indicator NOTE: If you accidentally pull the door, it may not shut properly. Push the door back in to shut it. 2 DTV indicator red: STANDBY green: ON Lights when receiving a digital television broadcast.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 8 RETURN button 0 INPUT 4 jacks Press to set the Projection Monitor to its initial mode. These inputs are for Video Movie and VCR. Use RCA-type pin plug cords (the same as those used in Hi-Fi systems) and SVIDEO cords for connections. When the audio source to be connected is monaural, connect the source to the L-(MONO) jack.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 REMOTE CONTROL UNIT (AXD1448: CU-SD110) for PRO-610HD and PRO-510HD Set the mode switch to TV/DTV. 1 TV POWER button (STANDBY/ON) Turns the power of the monitor on and off. 2 Input Selector buttons (TV, DTV*1, INPUT 1 to INPUT 4) Press the button to select the source you wish to watch. The screen will display your selection. 3 SCREEN MODE button Press to select the SCREEN MODE.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 0 SPLIT/SEARCH screen buttons SPLIT: Press to turn the SPLIT screen function on and off. SEARCH: Press to select the SEARCH screen mode. SELECT: Selects the screen for switching the channel or input source.*2 FREEZE: When this button is pressed with the regular screen, the screen will change to the SPLIT screen and the picture at the time the button was pressed will become the sub-picture, displayed as a frozen image.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 PANEL FACILITIES for SD-582HD5 and SD-532HD5 A flip-down door conceals the control panel. Push gently and release, to open the door. To close the door, lift it back up into place. 1 POWER STANDBY/ON indicator NOTE: If you accidentally pull the door, it may not shut properly. Push the door back in to shut it. 2 DPO sensor red: STANDBY green: ON Sensor to detect the room brightness. 3 MAIN POWER switch Press once to turn on the main power (STANDBY mode).
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 7 RETURN button CAUTION: Press to set the Projection Monitor to its initial mode. Do not press any operation button on the Projection Monitor or the remote control unit while recording. Signals from the MONITOR OUTPUT jacks may be temporarily interrupted when a button is pressed.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 REMOTE CONTROL UNIT (AXD1449: CU-SD111) for SD-582HD5 and SD-532HD5 Set the mode switch to TV. 1 TV POWER button (STANDBY/ON) Turns the power of the monitor on and off. 2 Input Selector buttons (TV, INPUT 1 to INPUT 4) Press the button to select the source you wish to watch. The screen will display your selection. 3 SCREEN MODE button Press to select the SCREEN MODE.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 REMOTE CONTROL UNIT FUNCTIONS 0 SPLIT/SEARCH screen buttons SPLIT: Press to turn the SPLIT screen function on and off. SEARCH: Press to select the SEARCH screen mode. SELECT: Selects the screen for switching the channel or input source.*1 FREEZE: When this button is pressed with the regular screen, the screen will change to the SPLIT screen and the picture at the time the button was pressed will become the sub-picture, displayed as a frozen image.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 SPECIFICATIONS for PRO-610HD and PRO-510HD Display and amplifier section Electrical section, miscellaneous Reception system ........ American TV standard NTSC system Screen size ................................................. 58" (PRO-610HD) 53" (PRO-510HD) CRT ..................................................... 7" High focus CRT x 3 Brightness (White peak) .......
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 SPECIFICATIONS for SD-582HD5 and SD-532HD5 Display and amplifier section Electrical section, miscellaneous Reception system ........ American TV standard NTSC system Screen size ................................................. 58" (SD-582HD5) 53" (SD-532HD5) CRT ..................................................... 7" High focus CRT x 3 Brightness (White peak) .......