Installation Manual SPH-DA210 SPH-DA110 AppRadio
Connecting the system Precautions before connecting the system WARNING Do not take any steps to tamper with or disable the parking brake interlock system which is in place for your protection. Tampering with or disabling the parking brake interlock system could result in serious injury or death. CAUTION • If you decide to perform the installation yourself, and have special training and experience in the mobile electronics installations, please carefully follow all of the steps in the installation manual.
Connecting the system OF OF O STAR T ACC position F N Power amp STAR • Use speakers over 50 W (output value) and between 4 Ω to 8 Ω (impedance value). Do not use 1 Ω to 3 Ω speakers for this unit. • The black cable is ground. When installing this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly connected to metal parts of the car’s body.
Connecting the system Parts supplied Installing the HDMI® cable holder 1 Insert the lower tab of the HDMI cable holder into the groove of this product. Groove This product Power cord GPS antenna Microphone Tab HDMI cable holder 2 Insert the two upper tabs into the this product by pushing the HDMI cable holder. Tabs p Use the HDMI cable holder when you connect this product with the separately sold HDMI/USB interface cable for iPod / iPhone (CD-IH202) or App Connectivity Kit (CD-AH200).
Connecting the system Connecting the system This product 3.55 m (1 ft. 2 in.) Wired remote input Please refer to the instruction manual for the Hard-wired remote control adapter (sold separately). 4m (13 ft. 1 in.) GPS antenna Vehicle antenna Microphone WARNING • To avoid the risk of accident and the potential violation of applicable laws, this product should never be used while the vehicle is being driven except for navigation purposes.
Connecting the system When connecting an iPhone with 30-pin USB interface cable for iPod / iPhone (*4) (sold separately) 2m (6 ft. 7 in.) iPhone with 30-pin (*3) (*3) For details concerning operations and compatibility, refer to the Operation Manual. (*4) For details about how to connect the separately sold USB interface cable for iPod / iPhone (CD-IU201N), refer to the USB interface cable for iPod / iPhone manual.
Connecting the system When connecting an Android device with an MHL port USB cable (*8) (Type USB A - USB A) (sold separately) 0.75 m (2 ft. 6 in.) USB cable USB - micro USB cable (*8) (Type USB A - micro USB B) (sold separately) 1.5 m (4 ft. 11 in.) HDMI cable holder HDMI port MHL adapter (*8) (sold separately) Android device (*7) High Speed HDMI® Cable (*8) (Type A - A)(sold separately) (*7) For details concerning operations and compatibility, refer to the Operation Manual.
Connecting the system Connecting the power cord (1) Yellow To terminal supplied with power regardless of ignition switch position. Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF. Orange/white To lighting switch terminal. Black (ground) To vehicle (metal) body. Notes • When a subwoofer is connected to this product instead of a rear speaker, change the rear output setting in the initial setting. (Refer to the Operation Manual.) • The subwoofer output of this product is monaural.
Connecting the system 10 This product Fuse (10 A) Power cord Blue/white To auto-antenna relay control terminal. If the vehicle has a glass antenna, connect to the antenna booster power control terminal (max. 300 mA 12 V DC).
Connecting the system Connecting the power cord (2) This product Power cord Light green (PARKING BRAKE) Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply side of the parking brake switch. If this connection is made incorrectly or omitted, certain functions of this product will be unusable. Violet/white (REVERSE GEAR SIGNAL INPUT) This is connected so that the this product can detect whether the vehicle is moving forwards or backwards.
Connecting the system When connecting to separately sold power amp/subwoofer Front outputs (FL, FR) This product Power amp (sold separately) RCA cables (sold separately) Power amp (sold separately) Subwoofer/rear outputs (SW/RL, SW/RR) Power cord System remote control Blue/white To system control terminal of the power amp (max. 300 mA 12 V DC).
Connecting the system This product When connecting a rear view camera When this product is used with a rear view camera, it is possible to automatically switch from the video to rear view image when the shift lever is moved to REVERSE (R). Rear View mode also allows you to check what is behind you while driving. Power cord Violet/white (REVERSE GEAR SIGNAL INPUT) WARNING USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY RESULT IN INJURY OR DAMAGE.
Installation Precautions before installation CAUTION • Never install this product in places where, or in a manner that: – Could injure the driver or passengers if the vehicle stops suddenly. – May interfere with the driver’s operation of the vehicle, such as on the floor in front of the driver’s seat, or close to the steering wheel or shift lever. • Make sure there is nothing behind the dashboard or paneling when drilling holes in them.
Installation Installing this product Installation notes • Do not install this product in places subject to high temperatures or humidity, such as: – Places close to a heater, vent or air conditioner. – Places exposed to direct sunlight, such as on top of the dashboard. – Places that may be exposed to rain, such as close to the door or on the vehicle’s floor. • Install this product in an area strong enough to bear its weight.
Installation Parts supplied The display unit Installation using the screw holes on the side of this product Truss head screw (5 mm × 8 mm) (6 pcs.) 1 Fasten the unit to the factory radiomounting bracket. Position this product so that its screw holes are aligned with the screw holes of the bracket, and tighten the screws at three or four locations on each side. Use either the truss head screws (5 mm × 8 mm) or flush surface screws (5 mm × 9 mm), depending on the shape of the bracket’s screw holes.
Installation Installing the GPS antenna Parts supplied CAUTION Do not cut the GPS antenna lead to shorten it or use an extension to make it longer. Altering the antenna cable could result in a short circuit or malfunction and permanent damage to this product. Installation notes • The antenna should be installed on a level surface where radio waves will be blocked as little as possible. Radio waves cannot be received by the antenna if reception from the satellite is blocked.
Installation When installing the antenna inside the vehicle (on the dashboard or rear shelf) WARNING Do not install the GPS antenna over any sensors or vents on the dashboard of the vehicle, as doing so may interfere with the proper functioning of such sensors or vents and may compromise the ability of the metal sheet under the GPS antenna to properly and securely affix to the dashboard. Affix the metal sheet on the surface as level as possible where the GPS antenna faces the window.
Installation Installing the microphone • Install the microphone in a place where its direction and distance from the driver make it easiest to pick up the driver’s voice. • Be sure to turn off (ACC OFF) the product before connecting the microphone. 2 Attach the microphone clip to the sun visor. Microphone clip Parts supplied Double-sided tape Microphone Mounting on the sun visor 1 Fit the microphone lead into the groove.
Installation Installation on the steering column 1 Detach the microphone base from the microphone clip by sliding the microphone base while pressing the tab. Tab Microphone Clamps Use separately sold clamps to secure the lead where necessary inside the vehicle. Microphone clip Microphone base 2 Mount the microphone on the steering column. Adjusting the microphone angle The microphone angle can be adjusted.