User Manual

Additional information
08
46
En
08
HDMI
No picture or sound.
 If the problem still persists when connecting your HDMI
component directly to your monitor, please consult the
component or monitor manual or contact the manufacturer
for support.
No picture.
 Video signals that are input from the analog video terminal
will not output from the HDMI terminal. Signals that are input
from the HDMI terminal will not output from the analog video
terminal. Be consistent with the type of cable between input
and output.
 Depending in the output settings of the source component, it
may be outputting a video format that can’t be displayed.
Change the output settings of the source, or connect using
the composite video jacks.
 This receiver is HDCP-compatible. Check that the components
you are connecting are also HDCP-compatible. If they are not,
please connect them using the composite video jacks.
 Depending on the connected source component, it’s possible
that it will not work with this receiver (even if it is HDCP-
compatible). In this case, connect using the composite video
jacks between source and receiver.
 If video images do not appear on your TV, try adjusting the
resolution, Deep Color or other setting for your component.
 To output signals in Deep Color, use an HDMI cable (High
Speed HDMI
®
Cable) to connect this receiver to a component
or TV with the Deep Color feature.
The OSD screen (Home Menu, etc.) isn’t displayed.
 The OSD will not appear if you have connected using the
HDMI output to your TV. Use composite connections when
setting up the system.
No sound, or sound suddenly ceases.
 Check that the HDMI setting is set to AMP (refer to page 33).
 If the component is a DVI device, use a separate connection
for the audio.
 HDMI format digital audio transmissions require a longer time
to be recognized. Due to this, interruption in the audio may
occur when switching between audio formats or beginning
playback.
 Turning on/off the device connected to this unit’s HDMI OUT
terminal during playback, or disconnecting/connecting the
HDMI cable during playback, may cause noise or interrupted
audio.
Synchronized operation not possible using Control with
HDMI function.
 Check the HDMI connections.
 The cable may be damaged.
 Select ON for the Control with HDMI setting (see HDMI Setup
on page 41).
 Turn the TV’s power on before turning on this receiver’s power.
 Set the TV side Control with HDMI setting to on (see TV’s
operating instructions).
 When the Ecology mode is switched on, the Control with
HDMI function does not work.
 When the Ecology mode is turned off again, the Control with
HDMI function may not work. In this case, see Before using
synchronization on page 42.
Important information regarding the HDMI
connection
There are cases where you may not be able to route HDMI
signals through this receiver (this depends on the HDMI
equipped component you are connecting-check with the
manufacturer for HDMI compatibility information).
If you aren’t receiving HDMI signals properly through this
receiver (from your component), please try the following
configuration when connecting up.
Configuration
Connect your HDMI-equipped component directly to the
display using an HDMI cable. Then use the most convenient
connection (digital is recommended) for sending audio to the
receiver. See the operating instructions for more on audio
connections. Set the display volume to minimum when using
this configuration.
Note
• Depending on the component, audio output may be
limited to the number of channels available from the
connected display unit (for example audio output is
reduced to 2 channels for a monitor with stereo audio
limitations).
• If you want to switch the input source, you’ll have to
switch functions on both the receiver and your display
unit.
• Since the sound is muted on the display when using the
HDMI connection, you must adjust the volume on the
display every time you switch input sources.
About status messages
Refer to the following information when you come up with a
status message while operating the NETWORK function.
Status messages Descriptions
List empty, Add from
Now Playing...
The list is empty. Please add from Now
Playing.
No item There are no items.
Rescanning devices... Rescanning. Please wait.
Unsupported Format This format is not supported.
Server Connection
Error
Cannot connect to server.
Error opening stream This is a stream error.
Already in favorites This is already registered in your
favorites.
Unsupported item This item is not supported by this
receiver.
Unknown error An unidentified error has occurred.
Connection Error... Cannot connect to network.