Operator's Manual

ManualsBrandsPiranha ManualsPaintball07gti

INSTRUCTIONS FOR USE

The Piranha

GTI is capable of high rates of fire and an agitating hopper such as an

Extreme Rage

Overdrive

™

is recommended for better performance.

Cocking Rod

Velocity

Adjustment

Screw

Safety Slide

Sear Release

Gas Thru Grip

PMI High Per

formance Barrel

Bottom Line

Adapter

Dual Ball Detents

OPERATING THE PIRANHA

GTI: 1. Attach threaded barrel

firmly to marker. 2. At this time, do not attach air source or loader and do

not load paintballs into marker. 3. Insert barrel plug firmly into barrel.

4. Pull the cocking knob straight back from the rear of the marker until the

cocking mechanism locks back in the cocked position. Always cock marker

before airing it up. During cocking the flush cocking rod will recoil or “spring

back” into the marker once released and will only move slightly during

marker operation. 5. Slide safety “of

f,” 6. Squeeze the trigger with an even

pressure. You should hear the hammer and bolt assembly slide forward.

7. Cock the marker. 8. Before attaching the air source, read and understand

the section in the manual on “Compressed Gas/Air.” Follow safety rules for

handling compressed gas/air. If any leak occurs in the marker, refer to trou-

bleshooting guide or to a qualified airsmith. Use only cylinders for com-

pressed gas or air that comply with all applicable laws and regulations,

including but not limited to those of the U.S. Depar

tment of T

ranspor

tation,

OSHA, Compressed Gas Association, and/or American Society for Testing and

Materials. 9. With goggles on, test for function after attaching air source:

Squeeze the trigger. The marker should shoot air and the cocking knob

should cycle slightly after each trigger squeeze, repeat several times. Flush

cocking rods will bobble some, but they will not come out all the way.

10. Slide safety forward (semi version). Paintballs may then be loaded.

WARNING: READ OPERATOR’S MANUAL BEFORE USE. EVERY PERSON WITHIN RANGE OF AN AREA WHERE A PAINTBALL

MARKER IS IN USE MUST WEAR PROTECTIVE GOGGLES AND HEADGEAR SPECIFICALLY DESIGNED FOR PAINTBALL.

WARNING: ALWAYS COCK MARKER BEFORE ATTACHING AIR SOURCE. MARKER CAN DISCHARGE IF AIR SOURCE IS ATTACHED

BEFORE MARKER IS COCKED. THE MARKER CONTAINS COMPRESSED GAS OR AIR WHEN PRESSURIZED. NEVER DISASSEMBLE MARK-

ER UNTIL REMOVING ALL GAS OR AIR FROM THE SYSTEM. RULES FOR SAFE HANDLING OF COMPRESSED GAS OR AIR MUST BE FOL-

LOWED AT ALL TIMES.

WARNING: BEFORE DISASSEMBLY, STORAGE, OR TRANSPORT OF THE MARKER, REMOVE AIR SOURCE FIRST, THEN REMOVE ALL

PAINTBALLS FROM THE MARKER, BARREL, AND LOADER. REMOVE ALL GAS OR AIR FROM THE MARKER. INSERT BARREL PLUG AND

SLIDE THE MECHANICAL SAFETY FORWARD SO THE SAFETY IS ENGAGED AND THE RED DOT IS NOT LIT. THE SAFETY IS A SMALL

MECHANICAL SLIDE ON THE LEFT SIDE OF THE MARKER ABOVE THE TRIGGER. WHEN THE SAFETY IS “OFF,” A RED DOT IS VISIBLE ON

THE MARKER. THE TRIGGER CAN STILL BE PULLED IF THE SAFETY IS “ON,” BUT THE MARKER WILL NOT FIRE OR DE-COCK. E-FORCE

MODEL: THE ON/OFF BUTTON ON THE LEFT SIDE OF THE FRAME SHOULD BE USED AS SAFETY.

WARNING: WHEN COCKING THE PRESSURIZED MARKER, DO NOT RELEASE THE COCKING KNOB UNTIL AFTER THE COCKING MECHANISM

HAS LOCKED BACK INTO THE COCKED POSTITION; RELEASING THE COCKING KNOB DURING COCKING CAN CAUSE THE MARKER TO SHOOT.

07GTIInstructions 7/5/06 9:59 AM Page 1

Summary of content (2 pages)

PAGE 1
07GTIInstructions 7/5/06 9:59 AM Page 1 INSTRUCTIONS FOR USE The Piranha® GTI is capable of high rates of fire and an agitating hopper such as an Extreme Rage® Overdrive™ is recommended for better performance. WARNING: READ OPERATOR’S MANUAL BEFORE USE. EVERY PERSON WITHIN RANGE OF AN AREA WHERE A PAINTBALL MARKER IS IN USE MUST WEAR PROTECTIVE GOGGLES AND HEADGEAR SPECIFICALLY DESIGNED FOR PAINTBALL. WARNING: ALWAYS COCK MARKER BEFORE ATTACHING AIR SOURCE.
PAGE 2
07GTIInstructions 7/5/06 9:59 AM Page 2 1A. Milled Receiver Body - Matte Black 1B. Milled Receiver Body - Matte Blue 1C. Milled Receiver Body - Matte Gunmetal 2. 9” Barrel 3. End Cap GTI 5. Field Strip Pin Assembly 6. Valve Body 7. Red Valve Cup Seal Assembly 7. Black Valve Cup Seal Assembly 8A. Removable Low Rise - Matte Black 8B. Removable Low Rise - Matte Blue 8C. Removable Low Rise - Matte Gunmetal 9. Valve Guide 10. Valve Spring 11. Molded Flush Cocking Bolt 12.