User Guide

15SV61228 Rev. A
W983 Stacker/W863 Dryer Operating Guide
W983 Stacker Setup Table
Media/
Resolution
Thickness Media
Stop
Full Arm
Fixture
Setting
- Scale on
Ramp
Full Arm
Tip Setting
- Scale on
Arm
Distance-
Printer
Output
Edge to
Stacker lip
Horizontal
Distance
From Printer
Output Edge
Speed
Setting - w/
1” Overlap
Speed Setting
- w/1” Gap
Between Pieces
Speed
Setting
-No Gap
Between
Pieces
Capacity Recom-
mended
Speed
Distance - Hold
Down Retainers
to Conveyor
Surface
3 x 5 Postcard/
Draft,Super Draft
Empty 11 0.0 10.5 1.0” 0” 4.0 6.0 5.0 898 4.0 to 6.0 0
3 x 5 Postcard/
Letter Mode
Empty 11 0.0 10.5 1.25” 0” 3.5 5.0 4.5 860 3.5 to 5.0 0
3 x 5 Postcard/
Executive Mode
Empty 11 0.0 10.5 2.0” 0” 2.0 2.2 2.1 720 2.0 to 3.0 0
# 10 Envelope/
Draft,Super Draft
Empty 3.0 4.0 11.5 1.0” 0” 4.0 6.5 5.5 450 6.5 0
1/8 3.0 4.0 11.5 1.0” 0” 4.0* 6.5 5.5 349 6.5 0.25”
3/8 3.0 4.0 11.5 2.0” 0” 5.0* 6.5 5.5 40 8.0 3”
# 10 Envelope/
Letter Mode
Empty 3.0 4.0 11.5 1.5” 0” 3.5 5.0 4.0 425 5.0 0
1/8 3.0 4.0 11.5 1.5” 0.5” 3.5 5.0 4.0 333 4.0 1.5”
3/8 3.0 .5 4.0 3.5” 0.5” 3.0 5.5* 4.0* 50 3.0 2”
# 10 Envelope/
Executive Mode
Empty 3.0 4.0 11.5 2.5” 0” 2.0 2.5 2.2 400 3.0 0
1/8 3.0 4.0 11.5 3.0” 0” 2.0* 2.5* 2.2 326 3.0 0.25”
3/8 3.0 4.0 11.5 4.0” 1” 3.0 3.5 3.2 40 4.5 N/U
Flat Envelope/
Draft,Super Draft
Empty 0.0 0.0 6.5 2.75” 2.5” 7.0 8.0* 7.5* 210 5.5 0.5”
1/4 0.0 7.5 11.5 3.0” 3.5” 7.0 8.0 7.5 75 7.5 1.5”
3/8 0.0 7.5 11.0 4.25” 1.0” 6.0 7.0* 6.5* 25 5.0 1.5”
Flat Envelope/
Letter Mode
Empty 0.0 0.0 6.5 3.0” 3.0” 6.0 7.0* 5.5* 150 4.0 0.5”
1/4 0.0 7.5 11.5 4.0” 4.0” 6.0 7.0 6.5 90 6.0 1.5”
3/8 0.0 7.5 11.0 4.0” 3.0” 3.0* 3.5* 4.0* 20 5.0 2”
Flat Envelope/
Executive Mode
Empty 0.0 0.0 6.5 3.0” 4.0” 3.0 3.5 5.5* 150 4.0 0.5”
1/4 0.0 7.5 11.5 4.0” 1.5” 3.0 3.4* 3.2 80 3.0 2”
3/8 0.0 7.5 11.0 4.0” 3.0” 2.5 3.0 2.7 20 3.5 2”
N/U – Not used. Raise or slide springs so that they do not interfere with the pieces. * Not recommended
Stacker_Dryer Op Guide Book.indb 15Stacker_Dryer Op Guide Book.indb 15 3/30/2004 10:26:46 AM3/30/2004 10:26:46 AM