Made in Holland Installation and handling instructions PITT® cooking in kitchen worktops These documents contain instructions to securely and successfully install PITT® cooking into kitchen worktops. Furthermore, they indicate which level of craftsmanship is required. To make a warranty claim, installation procedures should be applied as described. PITT® cooking is exclusively intended for consumer use.
Content 1. Worktop Materials suitable for PITT® cooking 3 2. Manufacturing recesses (cut-outs) 5 3. Application in Solid Surface 6 4. Installation kitchen worktop 8 5.
1. Worktop material suitable for PITT® cooking 1a. PITT® cooking can safely be built into: • • • • • • • • Compact board (eg. Trespa) Solid Surface Quartz Composite (eg. Caesarstone, Silestone) Concrete Glass Natural stone (eg. granite, marble) Stainless steel Ceramics (eg. Neolith) ! PITT® cooking should never be installed into solid wood and worktops with an HPL top layer. ! Additional requirements apply to Solid Surface. See chapter 3. 1b.
2. Manufacturing recesses (cut-outs) ! The guidelines of the kitchen manufacturer and/or the manufacturer of the kitchen worktop should always be strictly followed. 529/32” 235/8” 131/32” /32” 5 35 Fig. 1 2a. 13/8” The C-size for Top Side models should be at least 131/32” (50 mm) (fig.1). The distance between the cut out and the sides (left or right) of the worktop should be at least 529/32” (150 mm).
2. Manufacturing recesses (cut-outs) Fig. 5 2c. Fig. 6 The insides of the recess(es) should be smooth and even (fig. 5). Irregularities can cause cracking (fig. 6). Facet /64 x 3/64” 3 Fig. 7 2d. On the top and bottom of the recess(es) should be a facet of at least 3/64 x 3/64” (1x1 mm) be applied (with exception for Solid Surface) (fig. 7). 927/32” Fig. 7 2e. Fig. 8 Adhesive connections and/or interconnections should never intersect the recess(es).
3. Manufacturing recesses (cut-outs) | Solid Surface The guidelines of the manufacturer of the Solid Surface material should always be strictly followed. ! In case of Solid Surface the following extra instructions apply: 3a. Use a router or CNC machine to prevent jagged recesses. Extra plate Solid Surface Radius R = Fig. 10 /8” 1 Fig. 11 3b. Glue an extra Solid Surface plate at all times at the bottom of the worktop.
3. Manufacturing recesses (cut-outs) | Solid Surface Aluminum tape Thermo tape Aluminum tape Note! Tape may not be folded on edge of recess. Fig. 13 3e. Heat conductor Apply aluminium tape and thermo tape in the recess(es), in this order: 1) aluminum tape 2) thermo tape 3) aluminum tape (fig. 13).
The aluminum and thermo tape should be overlapping the top of the worktop surface with at least 13 /64” (5 mm). This seal will offer protection to the changes in temperature.
4. Installation worktop ! The guidelines of the kitchen manufacturer and/or the manufacturer of the kitchen worktop should always be strictly followed. Fig. 14 Fig. 15 4a. The cabinets should be placed perfectly levelled (fig. 14 and 15). 4b. In the case of bottom cabinets with a closed top, these should be the same size (+10 mm) as the PITT® cooking module. This is to bring the heat conductor in full contact with the core material. min. min. Fig. 16 4c. 4d. /8” 1 /8” 1 min. /8” 1 Fig.
5. Installation PITT® cooking into worktop Strictly follow the PITT® cooking installation instructions. The installation manual can be downloaded via www.pittcooking.com/downloads. ! 315/32” (88) Support bar Fig. 18 5a. Fig. 16 Fig. 19 The PITT® cooking module should always be fully supported with the PITT® cooking support set to prevent bending of the kitchen worktop (fig. 18 and 19). Fig. 20 5b.
In case of questions, please feel free to contact us via info@pittcooking.com or by phone via +31(0)88 088 7070. www.pittcooking.