BLACKVUE LCD
Table of Contents Introduction to the Manual Cautions for Safety Getting Started Checks for the External GPS Checks for the microSD Card Management During Summer Season Product Features Package Components Name of Each Part Attach & Detach the Mounting Holder of the Front View Camera Attach & Detach the Mounting Holder of the Rear View Camera Install the BlackVue 4 Video Recording 5 8 8 9 9 10 11 13 13 Checking Installation Position 14 Insert & Remove the microSD Card Installation 15 16 Simple Video
Introduction to the Manual Thank you for purchasing this product manufactured by Pittasoft Co., Ltd. This document contains information on how to operate this product. Before using the product, make sure to read through this document so as to use the product properly. In order to enhance the performance of the product, the contents of this document may be changed without prior notice.
Getting Started Cautions for Safety The purpose of these cautions is to maintain user safety and to avoid damage to property. Please make sure to read through this document so as to use the product properly. Danger Death or property damage can be caused for users if the following directions are not followed: y Do not disassemble, repair, or alter the product yourself. It can cause fire, an electric shock, or malfunction. For internal inspection and repair, call your customer service center.
Warning Death or serious injury can be caused for users if the following directions are not followed: y Do not leave the product where infants, children, or pets can reach it. They might swallow small components, or their saliva could get into it and cause an explosion due to a short circuit. y While cleaning the inside of the car, do not spray water or wax directly onto the product. It can cause fire, an electric shock, or malfunction.
Caution Injury or property damage can be caused for users if the following directions are not followed: y Do not spray a detergent directly onto the exterior of this product. It can discolor or have a crack. Also, the product can have an error. y If the product is used outside the optimal temperature range (0oC ~ 60oC), performance can degrade or malfunction can be caused. y Check if this product has been properly installed.
Checks for the External GPS Checks for the microSD Card Even if the GPS isn’t working the video is recorded, but position coordinates and driving speed are not recorded. When used for the first time, or when the product is not used for three consecutive days, it will take some time for GPS to find the current position.
Management During Summer Season y Park in a shady place or an indoor parking lot. y If an outdoor parking lot is used, park away from direct sunlight. Also, open the window by 1 or 2 cm. y If the product is exposed to direct sunlight, cool the product down for a specific amount of time before use. y During summer, the temperature inside the vehicle may rise to 80°C-90°C due to sunlight. Keep the inside of the vehicle at an appropriate temperature.
SONY EXMOR CMOS Sensor Due to the SONY image sensor that ensures excellent image quality, clearer identification is ensured during the day and night Package Components Coaxial Cable For Excellent Data Transfer For reliable data transfer, high quality coaxial cables are used to prevent missing data and data loss. High Definition Wide-Angle Lens Using a high definition wide-angle lens, accidents can be accurately recorded.
Name of Each Part Front View Camera Camera Angle Control Bolt Double-Sided Tape for the Mounting Holder microSD Card (BlackVue Viewer and User Guide Included) V in (Terminal for Connecting to the Rear View Camera) DC in (Power Terminal) Mounting Holder Camera Lens Rear View Camera Connection Cable Note y Pictures of the components may differ from the actual. y To enhance the performance of the product, the components may be changed without prior notice.
Rear View Camera Mounting Holder Mounting Holder Detachment Button Camera Lens GPS (External GPS Terminal) LCD Screen microSD Card Slot Wi-Fi LED GPS LED REC LED Power Button t 1SFTTJOH 4IPSU 4UBSUT BOE TUPQT WPJDF SFDPSEJOH t 1SFTTJOH -POH 5VSOT PO PS Pò UIF QPXFS Note y The external GPS is sold separately.
Attach & Detach the Mounting Holder of the Front View Camera Attach & Detach the Mounting Holder of the Rear View Camera 1 2 1 Press the mounting holder detachment button and pull the front view camera. 2 Push the front view camera into the mounting holder to assemble the mounting holder to front view camera. Hold the mounting holder, and pull the rear view camera.
Install the BlackVue 1 Checking Installation Position It is recommended to install the front view camera next to the room mirror. Clean any foreign substances and moisture from the place where the product will be installed with a dry cloth. 2 It is recommended to install the rear view camera at the higher part of the back window. Note y Do not install the product where it can interfere with the driver's vision. y It is recommended to install the product at the spot specified.
Insert & Remove the microSD Card 1 Insert the microSD card into the microSD card slot, of the front view camera, in the direction as shown in the figure below: Caution y Do not remove the microSD card while it is saving or reading data. This may cause data damaged or malfunction. y Copy important data to other storage medias. Pittasoft Co., Ltd. is not accountable for data loss resulting from carelessness. Note y Insert or remove the microSD card only when the product is turned off.
Installation 1 In a bright and safe place, stop the vehicle engine and pull out the vehicle key. 2 Attach the front view camera on the vehicle windshield glass with doublesided tape. 3 4 5 Attach the lens of the rear view camera on the vehicle’s back window with double-sided tape, so that the lens can also be placed at the center of the vehicle. Connect the V in terminal of the front view camera to the V out terminal of the rear view camera by using the cable for connecting to the rear view camera.
6 Organize the cables, using the cable clip, to prevent the driver's vision from being interrupted. 8 Adjust the camera angle to view the LCD screen. Slightly unfasten the camera angle control bolt to adjust the angle; then fasten the bolt. Even if the prop is detached, the camera angle can be maintained. Thus, the camera can be installed at the same lens angle as before. Caution y Do not remove the microSD card while it is saving or reading data. This may cause data damaged or malfunction.
Video Recording Parking Recording Normal Recording 1 Once you start the vehicle engine, the BlackVue will automatically power on. 2 When the BlackVue is powered on, the normal recording will automatically start. The video can be checked from the LCD screen. 1 2 When in normal recording mode, if the vehicle does not move for five minutes or longer, the mode will automatically switch to parking recording mode.
Event Recording 1 During normal recording mode or parking recording mode, if an impact to the vehicle is detected, event recording will start. 10 seconds before impact to the vehicle will also be recorded. Emergency Recording 1 Press the on the LCD screen to record the desired image. The recorded file will be saved in the form of an event recording file. Note Note y The degree of sensitivity, which impact detection sensitivity, can be set in Settings.
Simple Video Playback Playback in BlackVue You can directly check recorded videos from the LCD screen. 1 Press 2 From the list, select the recorded video you want to play back. 20 on the LCD screen. A list of recorded videos will appear. Note y When playing back a video, a video recording cannot be made using BlackVue.
Playback Using a GPS Navigation Playback Using a microSD Card Recorded videos can be played back using GPS navigation. Playback Using a Smartphone With a Smartphone that supports microSD cards, a video can be viewed. 1 1 Insert the included microSD card into the microSD card reader. 2 Connect the microSD card reader to navigation. Turn off the power of this product, and detach the microSD card. Note y For details on how to detach the microSD card, refer to Insert & Remove the microSD Card.
Note y A method for playing back recorded videos may differ depending on navigations. For details, refer to the User's Guide on Navigations. y If there are many recorded videos in the microSD card, it may take long to load a file. y Some navigations do not enable full HD video playback. Playback Using a PC Recorded videos can be checked immediately, using the video playback PC program. 1 Insert the included microSD card into the microSD card reader. 2 Connect the microSD card reader to navigation.
Playback Using the BlackVue App Wi-Fi is required to play back a video via BlackVue application. For a model that does not enable Wi-Fi, insert the microSD card into a Smartphone to play back a recording. 1 3 Touch the Wi-Fi button of the BlackVue application. Select the device you want to connect, and enter the password. (E.g. DR750LW-A682DE) Touch the OK button to connect to the selected device. The initial password is blackvue, but the user can change it.
Note y If information on Wi-Fi connection is saved, touch the Wi-Fi button of the BlackVue application, without enabling the Wi-Fi feature of the Smartphone, to automatically connect to Wi-Fi. y For the Live View function, Wi-Fi can be used within a 10m range, although the range may vary depending on the circumstances during use y When playing back recorded videos using Wi-Fi, the reception may vary according to the data transfer rate. y For details on Wi-Fi settings, refer to Wi-Fi and Other Settings.
Using the BlackVue Switch to Live View The front/rear screen recordings in this product can be checked in real-time. 1 2 Press on the LCD screen. If the screen is turned off, press the LCD screen to turn on the screen. Then, press . Whenever is selected, Live View will appear. Front + Rear PIP p Front Screen p Rear Screen Settings A setting can be changed in BlackVue. Press on the LCD screen. Note y When selecting settings, no videos can be recorded in BlackVue.
Item Description Screen Bright The brightness of the LCD screen can be adjusted. Screen On Time The waiting duration of the LCD screen can be set. Switch to the Rear The direction of a rear view camera video can be changed. The actual file is recorded in the forward direction. Touch revision If touch revision is required on the LCD screen, this option is available. 26 Video Settings Item Description Resolution The resolution of a recorded video can be set.
Audio Settings Item Recording Settings Description Voice Recording Voice recording can be enabled or disabled. Alarm Volume The BlackVue voice alarm volume can be adjusted. Note Item Description Normal Recording Enables or disables normal recording mode. Date/Time Display Turns on or off the date and time display recorded in a video. Speed Unit Display Changes the speed unit recorded in a video. File Unit Changes the unit of saving a recorded video.
Note System Settings y If Normal Recording and P Mode Auto Switch are set to OFF, only event recording videos will be saved. Item 28 Description Reset Settings Initializes settings. Wi-Fi Info. Wi-Fi connection information (e.g. SSID and password) can be checked. Language The language can be checked. System Info. The model name and firmware version can be checked. Timezone The time zone can be checked. The time zone setting is used as information on a recorded video.
Time Settings Sensitivity Settings The current time and time zone can be set. If an external GPS is connected, the time will be automatically set according to the time zones. Item Note y The time zone can be changed in the BlackVue Viewer. (Page 39) y The time can be synchronized with the smartphone by pressing Settings > Firmware > Auto Sync on the BlackVue App. Description Normal Mode In Normal recording mode, the impact sensitivity can be set when switching to event recording mode.
Power Settings SD Card Formatting The microSD card can be formatted or a format cycle message can be set. If a format cycle message is set, a message will appear in the cycle when this product is turned on. Item Description Min. Working Volt The minimum operating voltage can be set. In parking recording mode, once the vehicle battery voltage reaches under the setting value, the power supply will stop automatically to prevent battery from drainage. Battery Save Mode Battery save mode time can be set.
Using the BlackVue Viewer Screen Description Double-click the BlackVue Viewer icon in the microSD card to run BlackVue Viewer. In order to install BlackVue Viewer on the PC, connect to the BlackVue website (www. blackvue.com) and download it. 2 3 4 No. Name 1 Recorded Video Playback Window Videos can be played back using this window. The screen can zoom in/out by using a mouse. 2 Language Setting If you change the language on playback screen, the language for BlackVue Viewer can be changed.
No. Name Description Recorded Video List Using the file list and map tab, the recorded video list, including recording location can be confirmed. Click Front to display only rear view camera files in the recorded video list. Click Rear to display only front view camera files in the recorded video list. : This is an normal recording file and marked with green in the timeline. : This is an event and emergency recording file and marked with orange in the timeline.
Note Video Playback Playback Control A recorded video can be played back in full screen mode or reversed upside down. The playback speed can be adjusted to fast forward the video. Play Previous File Move Frame (Previous) Move Frame (Next) View Upside-Down Full Screen View Playback/Pause Stop Play Next File Playback Speed Control y While playing back recorded video, double-click the screen to switch to full screen view mode. Double-click the screen again or press ESC to return to default view.
Magnifying Glass You can zoom playback selected portions of recorded video. Left-click on the screen while playing back recorded video and a partial zoom-in window will appear. Move the window to identify the license plate. Timeline Video can be explored with the date, hr, min, and sec of when a video was recorded.
File Management With the recorded video list, a file can be deleted or saved with a different name. 1 2 3 Select a file from the recorded video list and right-click it. Note To delete a file, click Delete. y When you select Sound Off, the voice is removed from the recorded video to be saved. To save it with different name, click Export and select the option you want. 4 5 Click the OK button and select the file name you want, together with the path. Click the Save button to finish.
Map Check Verify Files With the recorded video list, a file can be verified forgery. 1 Select a file from the recorded video list and right-click it. The location of video recording can be confirmed on the map. 1 2 3 Select a file from the recorded video list and play it back. Click the Map tab. With the +/- button or mouse wheel, the map can be zoomed in/out. Speed Unit Change 2 Click Verification and click OK button.
Note y Internet connection is required to use the map service. y Only from recorded files with GPS information, data can be checked. MyWay Viewer Check The driving route of the video recording can be checked. 1 2 3 From the recorded video list, select and play back the desired file. Press the button. Then, the driving route will be displayed on the map. Double-click the map to play back the video recording from the driving route, nearest to the spot clicked.
Note Note y Internet connection is required to use the map service. y Only from recorded files with GPS information, data can be checked. y JPG and BMP are supported as image file formats. Image Printing Saving as an Image When playing back a recorded video, the desired part can be saved as an image. When playing back a recorded video, the desired part can be saved as an image. 1 2 From the recorded video list, select and play back the desired file.
Settings No. Function Description 1 Time Settings The time zone can be set for location used. The time zone setting is used as information on a recorded video. 2 Image Settings The quality and brightness of front/rear recorded videos can be set. For detailed information on video recording time, refer to Recording Time. (Page 48)) 3 Recording Settings Normal Record, Voice Record, Date and Time Display and Auto Switching to Parking Mode function can be turned on/off.
Time Setting If an external GPS is not connected, set time manually before use. If time is not set, the time of a recorded video may not be correctly saved. 1 2 3 Format the microSD card, and then upgrade the firmware. Connect to the website of BlackVue (www.blackvue.com), and download the time setting program. Run the time setting program before setting time.
Advanced Sensitivity Settings Sensitivity can be easily set while watching a recorded video. 1 2 3 1 2 No. Function Description 1 Sensitivity for Normal Recording It is possible to set the G-sensor sensitivity to start event recording during normal recording. 2 Sensitivity for Parking Mode It is possible to set the G-sensor and motion detection sensitivity to start event recording during parking recording mode. Click the G button. Then, click the Sensitivity tab.
4 Move the control bar upwards or downwards to adjust the sensitivity range. If the range is wide, it will be less sensitive. If the range is narrow, it will be more sensitive. It is recorded as an event. Wi-Fi and Other Settings Settings for Wi-Fi, LED indication, and voice announcements can be changed. It is not recorded as an event. 1 2 Note y If an event recording occurs due to the sensitivity setting while a recorded video is being played back, the edge of the playback screen will blink in orange.
No. 1 2 Function Description Wi-Fi Setting SSID and the password, which determines whether to automatically run Wi-Fi and enable WI-Fi connection can be changed. You can connect to Wi-Fi with the SSID and password settings in the BlackVue application. If the password is forgotten, you can reset the password. Other Settings For video recording status, normal recording mode, and parking recording mode, the LED indicators can be turned on/off. The voice announcement or volume can be changed.
How to Apply Configuration Firmware Upgrade Your settings can be applied to the product. 1 2 Insert the microSD card into the product. For details on how to insert the microSD card, refer to Insert & Remove the microSD Card. (Page 15)) Once power is turned on, your settings will be automatically applied. Note y Insert the microSD card only when the product is turned off. Connect the microSD card to the PC to upgrade firmware version. The firmware version can be upgraded with BlackVue application.
Note y Once firmware upgrade is completed, all of the settings will be initialized. y For details on how to insert the microSD card, refer to Insert & Remove the microSD Card. (Page 15) y Insert the microSD card only when the product is turned off. Caution y Make sure that the power is never turned off while firmware upgrade is in progress.
Resolution/Frame Front Rear Full HD (1920x1080) @30Fps Full HD (1920x1080) @30Fps Full HD (1920x1080) @30Fps HD (1280x720) @30Fps HD (1280x720) @30Fps HD (1280x720) @30Fps Ⲽ The resolution/frame can be changed. LCD Video Compression Type 3-Axe Acceleration Sensor Button Power Button Ⲽ Pressing Short: Starts and stops voice recording. Ⲽ Pressing Long: Turns on or off the power. Backup Battery Input Power MP4 Internal(802.11b/g/n(2.4~2.
Certificates Front: KC, CE, FCC, RoHS, Telec, WEEE Rear: KC, CE, FCC, RoHS, WEEE Software BlackVue Viewer Ⲽ Windows XP or higher (Windows 8 supported) and Mac Leopard OS X(10.5) or higher Application BlackVue Application (Android 2.3 or higher, iOS 5.0 or higher, and Windows 8.
Recording Time Resolution (Front+Rear) Full HD + Full HD @30fps Full HD + HD @30fps HD + HD @30fps 16 GB 3 HR 20 MIN 3 HR 50 MIN 4 HR 30 MIN 32GB 6 HR 40 MIN 7 HR 40 MIN 9 HR 64GB 13 HR 20 MIN 15 HR 20 MIN 18 HR Front 6 Mbps 6 Mbps 4 Mbps Rear 4 Mbps 3 Mbps 3 Mbps Item Memory Capacity Bit Rate Note y Depending on your environment, the actual recording duration may vary. y Depending on the image quality, the microSD card lifespan can be shorten.
Before Requesting A/S Service It is required for users to back up important data regularly from storage device (to other separate media). Depending on the situation, it will be necessary to delete the data from the internal storage device (component). It might be needed to delete all the data from the product for A/S. So it is required for users to back up important data by themselves before requesting A/S.
FCC Compliance Information THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Product Warranty Q This product is warranted for 1 year from the purchase date. (Accessories Such as Batteries and microSD Cards: Six Months) Q Pittasoft Co., Ltd. warrants its products under the Standard on Consumer Dispute Settlement (Announced by the Korea Fair Trade Commission). It is as follows: If a service is requested, Pittasoft or its designated subcontractor will provide the service. Product Name (Model Name) Purchase Date Customer Information Serial No.
Consumer Damage Type Defects Repair Enabled Performance/Functional Issues or Problems Under Normal Use Conditions Warranty Within the Warranty Term After the Warranty Term Free Repair Paid Repair/Paid Exchange/Free Repair After the Term of Free Warranty Failure Resulting From the Same Defect (Third Time) After Repair Failure (Fifth Time) After the Repair of Failures in Different Parts Loss of a Product Whose Repair was Requested Repair Disabled When repair cannot be conducted due to a lack of spare pa
MEMO
MEMO
MEMO
Name ] Car Dashcam Manufacturer ] Pittasoft Co.,Ltd. / Korea Address ] (Gasan-dong, BYC HIGHCITY), A-7th floor, 131, Gasan digital 1-ro, Geumcheon-gu, Seoul, 153-718, Republic of Korea Sales Headquater ] Tel: +82-2-6947-4670(#3) ] Fax: +82-2-6947-4699 ] e-mail: sales@pittasoft.