Wireless Timer Remote Control TW-282 中国制造 PSM40 V11.
Contents Overview Cautions TW-282 introduction The name of each part Prepare for install and use Install and replace the battery Fix the receiver(TW-282RX) Turned on/off the power Channel Setting Open the background light of display Receiver connected with the camera Shooting control Single shooting Continuous shooting within one sec 03 04 05 06 09 09 11 12 13 14 15 16 16 17 1
Overview Thank you for purchasing high-performance PIXEL products shooting Delay shooting Timing plan for shooting 19 20 23 First of all, thank you for purchasing product of Wireless Timer Remote Control TW-282. The shooting ways included single shooting, continuous shooting within one sec, BULB shooting, user-defined time-delay and timing plan for shooting. Low consumption of LCD display will make you be clear at a glance of the using status and using plan.
TW-282 introduction Cautions The batteries should not install anti-polarity; Otherwise the batteries may leak corrosive liquids, heat or explosion. Make sure the camera and receiver (TW-282RX) are powered off before install it. When connected the remote cable with the device, do not pull the wires. As this is an electronic product accessory; some of the environment causes may affect the working. However this is hardly ever to get this situation.
The name of each part The name of each part Please check all included items after open the packing, if missing, please contact the dealer. 1. Transmitter (TW-282TX) ------- 1pc 3. Shutter connect cable ---------- 1pc 4.
Preparation for installation and use The name of each part CLDC0 Display of transmitter 9 CL- CLDC1 DC2 CLE3 CLN3 CLL1 CLS1 CL- CLUC1 CB1 10 11 12 13 1 Install and replace the battery 1 2 The transmitter(TW-282TX) 2 3 4 5 6 7 8 Display of transmitter 1 3 5 7 9 11 13 8 Before use, you should read the user manual of your camera carefully and well understand the manipulation and functional setting. The function setting of camera may influence this item’s efficiency control of the camera.
Preparation for installation and use 2. Follow the signs of positive [ + ] and negative [ - ] in the battery compartment to install the battery correctly. You should pay attention to the polarity of battery because of the wrong installation will make the device work abnormally, or even physical injury. 3. Close the battery hatch.
Preparation for installation and use Turned on/off the power The transmitter(TW-282TX) 1. Press any button once, and turn on the power of transmitter. 2. The transmitter stays in the single shooting mode when you turn on the power; timing plan and channel setting will not be changed. 3. T h e d i s p l a y s h o w s t h e s i n g l e s h o o t i n g i c o n a n d communication channel. 4.
Preparation for installation and use Preparation for installation and use Open the background light of display Receiver connected with the camera The transmitter(TW-282TX) Press and hold the background light button for 2 seconds, the background light will be turned on. Open the background light and press the button twice each 6 seconds, the background light will keep lit. The background light will not be close by hand; it will turn off after 6 seconds automatically without any operation.
Shooting control Shooting control Sketch map for selecting function mode: Single shooting function Press Press Press Press Press Press Continuous shooting within one sec function shooting function 3. Full-press the release button and transmitter will send signal of shooting. The red indicator will light for a while, the camera start shooting.
Shooting control Shooting control shooting 2. Half-press the release button and transmitter will send signal for focusing, the green indicator will lit on the transmitter and receiver, and the camera is in the focusing state until the release or full-press the button. 3. Full-press the release button, red indicators of the transmitter and receiver will be lit, keep fully press the button, the transmitter will send signal of shooting continuously, the indicators will blink red and green light in turn.
Shooting control Shooting control Delay shooting The delay shooting function of TW-282 can user-defined the delay time and shots. Delay shooting setting 1. In the power-on state, move the transmitter’s activities icon to delay shooting icon[ ] by pressing the left move button[ ]or right move button[ ]. Press the set button entering the delay setting for adjusts the shooting numbers. The delay shooting icon[ ],number of shooting [ ]will blink at the same time. 2.
Shooting control Shooting control Timing plan for shooting 4. When countdown is completed, receiver will follow the setting shots output a signal per second to control shooting. 5、 Before delay time planning completed, press either transmitter button or receiver button or other , will terminate this planning. Make sure to set the camera function to be [ ]. When the camera function is set to be [ ], it will start continuous shooting.
Shooting control Shooting control Exposure time setting Interval time setting 1. Press left move button[ ]or right move button[ ], move the transmitter’s activities icon to the exposure timing program icon[ ]. 2. Press the set button, enter the delay time for ‘second bit’ setting. 3. By pressing button[ ]or[ ],enter into the setting for “minutes” and “hours”, as the sketch map.
Shooting control Shooting control Search the timing plan The shot number setting 1. Press left move button[ ]or right move button[ ], move the transmitter’s activities icon to the icon of timing shots [ ]. 2. Press the setting button enter to set the number of photo in timing plan' s, Press [ ] to increase the photo number; Press [ ] to reduce the photo number. 1-99photo number is available, when the screen display [ -- ] means this is unlimited to take the photo. 3.
Shooting control TW-282 Specification 3.Transmitter' s screen will display the running conditions of timing plan, but it will not send any command to the receiver. This is only showing the receiver running conditions and for reference only. Type : FSK 2.4 GHz wireless control system Transmission distance: 80 meters or above Channel: 15 channels Standby time: Transmitter : more than 4 years(using two 1.5V AAA batteries) Receiver : 400 hours (using CR-2 lithium battery) Transmitter: 149mm×49.
