PG11(Wireless USB Adapter) Installation Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. ⓒ2020. PIXXGEN Corporation. All rights reserved. REV1.
USB Adapter (Realtek) Installation Guide This manual is divided into three parts: Windows XP, Windows 7 / 8 / 8.1 /10, and Mac 1 .Windows XP Please do the following steps to set up the software on your computer: Step 1. Once the wireless USB adapter has been plugged in to a USB port, the following message will appear on screen. Click “Cancel”. (See picture below please) (If it does not pop-up, skip this step) Step 2. Please insert the disc into your CD-ROM drive.
Step 5: Click the Icon double click in the Windows system tray, which is located in the bottom-right corner of your computer screen or , and select “View Available Wireless Networks” to launch the utility. Find your network in the list of available networks. See image below. ⓒ2020. PIXXGEN Corporation. All rights reserved. REV1.
Double click on your network and type in your Network Key (the WiFi security password you chose while setting up your network or the internet provider gave you). You will have to confirm your Network Key. ⓒ2020. PIXXGEN Corporation. All rights reserved. REV1.
Now you will have access to the internet. ⓒ2020. PIXXGEN Corporation. All rights reserved. REV1.
2. Windows 7 / 8 / 8.1 / 10 This example uses Windows 7, but if you have Win 8 or 10, the steps are the same. Step 1. Once the wireless USB adapter is plugged into a USB port, insert the CD and locate Setup.exe in the folder “windows” in the disc directory. (If you do not have a CD-ROM slot in your computer, please download the driver from netdynwifi.com) Step 2. Double click on the Setup.exe file, then continue the installation wizard. Step 3.
Open the wireless networking page and enter the security key. Click the “OK” button. Then you should have internet access when you open a internet window with any browser. ⓒ2020. PIXXGEN Corporation. All rights reserved. REV1.
Suing the Realtek Utility: Step 4b. Double click the icon in the Windows system tray, which is located in the bottom-right hand corner of your computer screen, and click on the “Available Networks” button Choose wireless signal (See figure 2) and double click. ⓒ2020. PIXXGEN Corporation. All rights reserved. REV1.
Double Click on your network name and enter your wireless password under Network Key and Confirm Network Key. ⓒ2020. PIXXGEN Corporation. All rights reserved. REV1.
Now you will have access to the internet. Note: If there is no icon, please find it by clicking the small triangle at the bottom right of the screen. It has been hidden as following the picture shows: ⓒ2020. PIXXGEN Corporation. All rights reserved. REV1.
3. MAC OSX Step 1. Unzip the Driver for MAC OS, and then open the file “Installer.pkg”. Step 2. After you install the driver, you’ll have to restart your computer. Step 3. Open your Finder, and then click on “Applications”, find the “Wireless Network Utility” file, and click to open it. ⓒ2020. PIXXGEN Corporation. All rights reserved. REV1.
Step. 4 Click the “Available Network”, and then choose your WiFi network, and click “Connect”, type your password and you can get access to the Internet. ⓒ2020. PIXXGEN Corporation. All rights reserved. REV1.
ⓒ2020. PIXXGEN Corporation. All rights reserved. REV1.
Products using PG11 can only use the antenna below. Antenna Type Dual-band IPEX Antenna Model Name Connector Gain Xls-857 IPEX/MMCX/MHF4 etc ≤ 5 dBi Manufacture Shenzhen XinLi Sheng ≤ 4 dBi(2.
ANTENNA SPECIFICATION Dual-band IPEX Antenna ITEM No. Xls-857 Frequency range Gain 2400-2500MHz / 5150-5850MHz VSWR ≤2.0 Polarization Vertical Input Impedance 5dBi 50 Ohm Size L:46.5mm x W:9.0mm x T:1.0mm Cable type 1.
L:46.Smm W:9.0mm Cable:1.
#APPENDIX 1 FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. USERS MANUAL OF THE END PRODUCT: The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied.
Additional Test, Part 15 subpart B disclaimer The final host / module combination need to be evaluated against the FCC part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device.
