Planar Systems, Inc. Corporate Headquarters 1195 NW Compton Drive Beaverton, OR 97006-1992 Planar Customer Support Telephone: US: 1-866-PLANAR1 (866) 752-6271 Outside US: (503) 748-5799 E-mail: PlanarSupport@planar.com Online Technical Library: http://www.planar.
User’s Manual Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2008 Disclaimer The information in this document is subject to change without notice.
Preface Important Safety Information Congratulations on purchasing the Planar DLP® projector! Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
DLP® Projector – User’s Manual Power Safety Only use the supplied power cord. Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. Remove the batteries from the remote control when storing or not in use for a prolonged period. Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 35 for clear and safe instructions for this procedure. Before replacing the lamp: Unplug the power cord.
Preface Main Features • Lightweight unit, easy to pack away and transport. • Compatible with all major video standards including NTSC, PAL, and SECAM. • A high brightness rating allows for presentations in daylight or in lit rooms. • Supports resolutions up to SXGA at 16.7 million colors to deliver crisp, clear images. • Flexible setup allows for front, rear projections. • Line-of-vision projections remain square, with advanced keystone correction for angled projections.
DLP® Projector – User’s Manual Table of Contents GETTING STARTED........................................................................................................................................................... 1 PACKING CHECKLIST ........................................................................................................................................................... 1 VIEWS OF PROJECTOR PARTS .........................................................................................
Preface Check the audio cable connection................................................................................................................................. 43 HAVING THE PROJECTOR SERVICED .................................................................................................................................. 43 SPECIFICATIONS .............................................................................................................................................................
Getting Started Packing Checklist Carefully unpack the projector and check that the following items are included: PR6022 DLP projector Remote control (with one 3V CR2025 battery) RGB cable Power cord RGB to Component Adapter (Optional) Quick Start Guide CD-ROM (This User’s manual) Carrying case Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work.
DLP® Projector – User’s Manual Views of Projector Parts Front-right View Item Label Description 1. Ventilation opening To keep the projector lamp cool 2. Height-adjuster button Push to release height adjuster 3. Height adjuster Adjusts level of projector 4. Lens cap Covers lens to protect when not in use 5. IR receiver Receiver for IR signal from remote control 6. Lens Remove lens cap before use 7. Focus ring Focuses the projected image 8.
DLP® Projector – User’s Manual Top view—On-screen Display (OSD) buttons and LEDs Item Label 1. (Power) 2. ▲ (Up cursor) 3. Power LED 4. Over Temp LED 5. Ready LED Description See page: Turns the projector On or Off 11 Navigates and changes settings in the OSD 18 Green Power On Off Power Off (AC Off) Flashing Error code On System over temperature Off Normal State Orange Lamp is ready to be powered-on.
DLP® Projector – User’s Manual Rear view Item Label Description 1. AC IN Connect the power cable 2. USB (Service Only) Connect the USB cable from a computer (service only) 3. AUDIO Connect the AUDIO CABLE from the input device 4. S-VIDEO Connect the S-VIDEO CABLE from a video device 5. VIDEO Connect the VIDEO CABLE from a video device 6. VGA Connect the RGB CABLE from a computer and components 7.
DLP® Projector – User’s Manual Bottom view Item Label Description See page: 1. Lamp cover Remove when changing the lamp. 35 2. Height adjustor Adjuster drops down when adjuster button is pushed. 15 3. Lens cap hook To fasten the lens cap cover. 4. Tilt adjustor Rotate adjuster lever to adjust angle position. 5. Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling 15 Note: When installing, ensure that you use only UL Listed ceiling mounts.
DLP® Projector – User’s Manual Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. 3.
DLP® Projector – User’s Manual Item Label Description See page: 1. Up cursor Navigates and changes settings in the OSD 2. Enter Changes settings in the OSD 3. Power Turns the projector On or Off 11 4. Right cursor Navigates and changes settings in the OSD 18 5. Volume + Increase volume 18 17 6. Volume - Decrease volume 7. Mute Mutes the built-in speaker 8. Freeze Freeze/unfreezes the on-screen picture 9. Source Detects the input device 10.
DLP® Projector – User’s Manual Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.
Setup and Operation Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow (A). Pull out the cover (B). 2. Insert the battery with the positive side facing up. 3. Replace the cover. Caution: 1. Only use a 3V lithium battery (CR2025). 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the battery when not using the projector for prolonged periods.
DLP® Projector – User’s Manual Connecting Input Devices A PC or notebook computer and video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. Check the user manual of the connecting device to confirm it has the appropriate output connector. Item Label Description A USB (Service Only) Connect the USB cable from a computer (service only).
DLP® Projector – User’s Manual Starting and Shutting down the Projector 1. Connect the power cord to the projector. Connect the other end to a wall outlet. The Power and Ready LEDs on the projector light. 2. 3. Turn on the connected devices. Ensure the Ready LED displays a solid orange and not a flashing orange. Then press the Power button to turn on the projector. The projector splash screen displays and connected devices are detected.
DLP® Projector – User’s Manual 5. When the “Power Off? /Press Power again” message appears, press the Power button. The projector turns off. Caution: 1. Be sure to remove the lens cap before starting projector. 2. Do not unplug the power cord until the Ready LED stops flashing–indicating the projector has cooled down.
DLP® Projector – User’s Manual Setting an Access Password (Security Lock) You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. When enabled, the password must be entered after you power on the projector. (See Navigating the OSD on page 18 and Setting the OSD Language on page 19 for help on using OSD menus.) Important: Keep the password in a safe place. Without the password, you will not be able to use the projector.
DLP® Projector – User’s Manual 5. You can use the cursor buttons ▲▼◄► either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but not less than five. Press the cursor buttons in any order to set the password. Push the Menu button to exit the dialog box. 6. The password confirm menu appears when user presses the power-on key in case the Security Lock is enabled. Enter the password in the order you set it at step 5.
DLP® Projector – User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector: 1. • The projector table or stand should be level and sturdy. • Position the projector so that it is perpendicular to the screen. • Ensure the cables are in a safe location. You could trip over them. To raise the level of the projector, lift the projector [A] and press the height-adjuster button [B]. The height adjuster drops down [C]. 2. 3.
DLP® Projector – User’s Manual Adjusting the Zoom, Focus and Keystone 1. 2. Use the Image-zoom control (on the projector only) to resize the projected image and screen size B . Use the Image-focus control (on the projector only) to sharpen the projected image A . Remote control and OSD panel 3. The keystone control appears on the display.
DLP® Projector – User’s Manual Adjusting the Volume 1. 2. 3. Press the Volume +/buttons on the remote control. The volume control appears on the display. Press the Left or Right Cursor buttons on the keypad to adjust Volume +/-. Press the Mute button to turn off the volume (This feature is available only on the remote).
DLP® Projector – User’s Manual On-Screen Display (OSD) Menu Settings OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the remote control and on the projector. 1. To enter the OSD, press the Menu button. 2. There are five menus.
DLP® Projector – User’s Manual Setting the OSD Language Set the OSD language to your preference before continuing. 1. Press the Menu button. Press the cursor ◄► button to navigate to Installation I. 2. Press the cursor ▲▼ button until Language is highlighted. 3. Press the cursor ◄► button until the language you want is highlighted. 4. Press the Menu button twice to close the OSD.
DLP® Projector – User’s Manual OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting.
DLP® Projector – User’s Manual OSD Sub-Menu Overview – 21 –
DLP® Projector – User’s Manual Image Menu Press the Menu button to open the OSD menu. Press the cursor ◄► button to move to the Image Menu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to change values for settings. Item Description Display Mode Press the cursor ◄► button to set the Display Mode. Brilliant Color Press the cursor ◄► button to adjust the Brilliant Color value. Brightness Press the cursor ◄► button to adjust the display brightness.
DLP® Projector – User’s Manual Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Advanced menu and then press Enter or ►. Press ▼▲ to move up and down in the Advanced menu. Item Description Color Space Press the cursor ◄► button to adjust the color space. (Range: Auto – RGB – YPbPr- YCbCr) Color Temperature Press the cursor ◄► button to adjust the color temperature.
DLP® Projector – User’s Manual Color Manager Press (Enter) / ► to enter the Color Manager sub menu. Item Description Red Select to enter the Red Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. Green Select to enter the Green Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. Blue Select to enter the Blue Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. Cyan Select to enter the Cyan Color Manager.
DLP® Projector – User’s Manual Computer Menu Press the Menu button to open the OSD menu. Press the cursor ◄► button to move to the Computer menu. Press the cursor ▲▼ button to move up and down in the Computer menu. Press ◄► to change values for settings. Item Description Horizontal Position Press the cursor ◄► button to adjust the display position to left or right. Vertical Position Press the cursor ◄► button to adjust the display position to up or down.
DLP® Projector – User’s Manual Video/Audio Menu Press the Menu button to open the OSD menu. Press the cursor ◄► button to move to the Video/Audio menu. Press the cursor ▲▼ button to move up and down in the Video/Audio menu. Press ◄► to change values for settings. Item Description Video AGC Press the ◄► buttons to enable or disable the Automatic Gain Control for video source. Video Saturation Press the ◄► buttons to adjust the video saturation.
DLP® Projector – User’s Manual Audio Press Enter / ► to enter the audio submenu. Item Description Volume Press the ◄► buttons to adjust the audio volume. (Range: 0~8) Mute Press the ◄► buttons to turn on or off the speaker.
DLP® Projector – User’s Manual Installation I Menu Press the Menu button to open the OSD menu. Press the cursor ◄► button to move to the Installation I menu. Press the cursor ▲▼ button to move up and down in the Installation I menu. Press ◄► to change values for settings. Item Description Language Press the cursor ◄► button to select a different localization Menu. Blank Screen Press the cursor ◄► button to select different color to blank the screen.
DLP® Projector – User’s Manual Installation II Menu Press the Menu button to open the OSD menu. Press the cursor ◄► button to move to the Installation II menu. Press the cursor ▲▼ button to move up and down in the Installation II menu. Press ◄► to change values for settings. Item Description Auto Source Press the cursor ◄► button to enable or disable automatic source detection. (Range: On ~ Off) Auto Power Off (min.
DLP® Projector – User’s Manual Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Installation II menu. Press ▲▼ to move to the Advanced menu and then press Enter or ►. Press ▲▼ to move up and down in the Advanced menu. Press ◄► to change values for settings. Item Description OSD Menu Setting Press Enter / ► to enter the OSD setting menu. See page 31 for more information on OSD Menu Setting. Peripheral Test Press Enter/ ► to enter the Peripheral Test menu.
DLP® Projector – User’s Manual OSD Menu Setting Item Description Menu Position Press ◄► button to select different OSD location. Translucent Menu Press ◄► button to select OSD background translucent level. Menu Display Press ◄► button to select OSD timeout delay.
DLP® Projector – User’s Manual Peripheral Test Item Description Remote Control Test Press (Enter) / ► and follow the on-screen prompts to carry out the Remote Control Test. Press the Menu button twice to return to the Peripheral Test menu. USB Test Press (Enter) / ► and follow on-screen prompts to carry out the USB Test. Press the Menu button to return to the Peripheral Test menu. Button Test Press (Enter) / ► and follow the on-screen prompts to carry out the Button (display panel) Test.
DLP® Projector – User’s Manual Lamp Hour Reset Please refer to Resetting the Lamp on page 38 to reset the lamp hour counter.
DLP® Projector – User’s Manual Factory Reset Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the Factory (Enter) / ► to reset all the menu items to the factory default values Reset sub menu and press (expect Language and Security Lock). Status Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the (Enter) / ► to enter the Status sub menu. Installation II sub menu and press Item Description Active Source Display the activated source.
Maintenance and Security Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer. Important: a. The projection lamp used in this product contains a small amount of mercury. b. Do not dispose this product with general household waste. c. Disposal of this product must be carried out in accordance with the regulations of your local authority.
DLP® Projector – User’s Manual 3. 4. 5. Remove the two screws from the lamp module (A). Lift the module handle up (B). Pull firmly on the module handle to remove the lamp module.
DLP® Projector – User’s Manual 6. Reverse steps 1 to 5 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage. Note: The lamp module must sit securely in place and the lamp connector must be connected properly before tightening the screws.
DLP® Projector – User’s Manual Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 1. 2. 3. 4. Press the Menu button to open the OSD menu. Press the cursor ◄► button to move to the Installation II menu. Press the cursor button to move down to Advanced. Press the cursor ▼▲ button to move down to Lamp Hour Reset. Press the cursor ► or Enter button. A message screen appears. 5. 6. Press ▼▲◄► buttons to reset the lamp hour.
DLP® Projector – User’s Manual Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn. 2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the projector. 3.
DLP® Projector – User’s Manual Using the Kensington® Lock If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensington security cable. The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242, http://www.Kensington.com.
Troubleshooting Common problems and solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions. • Use some other electrical device to confirm that the electrical outlet is working.
DLP® Projector – User’s Manual LED Error Messages Error Code Messages Over Temp LED Power LED Blink Ready LED Blink Over temperature 0 ON 0 Thermal break status error 4 0 0 Lamp error 5 0 0 Fan1 error 6 0 1 Fan2 error 6 0 2 Fan3 error 6 0 3 Lamp door open 7 0 0 DMD error 8 0 0 Color wheel error 9 0 0 In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector.
DLP® Projector – User’s Manual Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is securely connected. 2. Ensure the power source is good by testing with another electrical device. 3. Restart the projector in the correct order and check that the Power LED is green. 4. If you have replaced the lamp recently, try resetting the lamp connections. 5. Replace the lamp module. 6. Put the old lamp back in the projector and have the projector serviced.
DLP® Projector – User’s Manual Specifications Input Connectors VGA PC USB (service only) Composite video (RCAx1) Video S-Video (Mini-DIN) Audio Mini-jack Security Kensington slot Projection Distance vs. Projection Size Projection Distance and Size Table PR6022 Tele Wide m 1.34 3.58 4.47 8.94 1.54 3.09 3.86 11.58 feet 52.76 140.94 175.98 351.97 60.63 121.65 151.97 455.91 Diagonal inches 30 80 100 200 40 80 100 300 Keystone degree 12.3 12.3 12.3 12.3 14.2 14.
DLP® Projector – User’s Manual Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. Resolution H-Sync (KHz) V-Sync (Hz) NTSC — 15.734 60.0 O — — PAL/SECAM — 15.625 50.0 O — — 640 x 350* 37.9 85.0 — — O 640 x 400* 37.9 85.0 — — O 720 x 400* 37.9 85.0 — — O 640 x 480 31.5 60.0 — — O 640 x 480 37.9 72.0 — — O 640 x 480 37.5 75.0 — — O 640 x 480 43.3 85.
DLP® Projector – User’s Manual Signal Resolution H-Sync (KHz) V-Sync (Hz) Composite / Component S-Video 640 x 480 35.0 66.68 — — O 832 x 624 49.725 74.55 — — O 1024 x 768 60.24 75.0 — — O 1152 x 870 68.68 75.06 — — O 480i 15.734 60 — O — 576i 15.625 50 — O — 480p 31.469 60 — O — 576p 31.25 50 — O — 720p 37.5 50 — O — 720p 45.0 60 — O — 1080i 33.8 60 — O — 1080i 28.
DLP® Projector – User’s Manual Projector Dimensions – 47 –
Regulatory Compliance FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Planar Systems, Inc. Corporate Headquarters 1195 NW Compton Drive Beaverton, OR 97006-1992 Planar Customer Support Telephone: US: 1-866-PLANAR1 (866) 752-6271 Outside US: (503) 748-5799 E-mail: PlanarSupport@planar.com Online Technical Library: http://www.planar.com/support 24/7 Technical Support © 2008 Planar Systems, Inc. Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners.
