PT1545R Touch Screen LCD Monitor USER’S GUIDE www.planartouch.
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced,translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows is a registered trademark of Microsoft, Inc.
Table of Contents Usage Notice Precautions............................................................................................................................. 1 Introduction About PT1545R ...................................................................................................................... 2 Touch Screen for PT1545R .......................................................................................... 2 Package Overview ..........................................................
Usage Notice ! ! Warning - To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. Warning - Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: • Turn off the product before cleaning.
Introduction About PT1545R The PT1545R is a 15" flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD). Features include: • Direct Analog signal input • Active matrix TFT LCD technology • 1024 x 768 XGA resolution • 15" viewable display area • 31.5 ~ 60 KHz horizontal scan • 56 ~ 75 Hz high refresh rate • 0.297mm x 0.
Package Overview LCD Display Power Cord VGA Signal Cable USB Cable ( A to B) RS-232 Cable Audio-in Cable xxxxxxxx xxxxxxxxx x / xxxxxxxxx USER’S GUI DE www.plana r.
Installation Product Overview • Front View • Bottom View AC IN VGA POWER SWITCH 4 Audio RS-232 USB
Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products. The Kensington lock is not included.
VESA Mount Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monitors, and corresponding with the standards of flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor. To mount the monitor on an UL-listed swing arm or other mounting fixture, follow the instructions included with the mounting fixture to be used.
Start Your Installation Please follow these instructions so that you can hookup the cables to associated connector. 1. Lay the LCD flat on an even surface. 2. Move the stand into position as seen in the step 2 diagram. 3. Remove the cable cover as seen in the step 3 diagram. 4. Connect the cables to the appropriate connectors as seen in the step 4 diagram. Use step 4-1 diagram if using the RS-232 serial connector. Use the step 4-2 diagram if using the USB connector. 5.
Remove the Deskstand Remove 4 screws and then remove hinge. Connecting the Display (Figure 11.1) To setup this display, please refer to the following figure and procedures. 1. 2. 3. 4. 5. 6. 7. ! Be sure all equipment is turned off. Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet (11.1). Connect the D-SUB cable from the display's VGA input connector to the D-SUB connector of your host computer and tighten the screws (11.1).
(Figure 11.
User Controls Side Panel Controls Icon key Name Menu Up Down Enter Power OSD Key Menu off status Menu on status Menu appear Menu disappear/ return to main item Brightness Main item select up/ Adjust up Mute Main item select down/ Adjust down Enter/Select sub-item function Power On/Off 10
How to Use the OSD Menus Icon key Name Menu Up Down Enter Power 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the six functions in the main menu. 2. Choose the adjustment items by pressing the “Enter ” button. 3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button. 4. With the OSD menu on screen, press “ Menu” button to return main menu or exit OSD. 5.
On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically. Left/Right Moving screen image horizontal position to left or right. Up/Down Moving screen image vertical position to up or down. Horizontal size The screen image horizontal dot clock adjustment. Fine The screen image pixel phase adjustment.
Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. ► Check that all the I/O and power connectors are correctly and well connected described in the "Installation" section. ► Make sure the pins of the connectors are not crooked or broken. Problem: Partial Image or incorrectly displayed image.
Warning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. There may be three sources for this problem. Please check the cable connections or contact your local dealer or our service center for more information. No Signal This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphics card.
Product Dimensions 306.5 274.8 350.8 Front View 201.4 59 Side View 202.0 222.
Compatibility Modes Mode Resolution H-Frequency (KHz) V-Frequency (Hz) IBM VGA 720 x 400 31.50 70 IBM VGA 640 x 480 31.50 60 VESA VGA 640 x 480 37.90 72 VESA VGA 640 x 480 37.50 75 VESA SVGA 800 x 600 35.20 56 VESA SVGA 800 x 600 37.90 60 VESA SVGA 800 x 600 48.10 72 VESA SVGA 800 x 600 46.90 75 VESA XGA 1024 x 768 48.40 60 VESA XGA 1024 x 768 56.50 70 VESA XGA 1024 x 768 60.00 75 Apple Mac II 640 x 480 35.00 66 Apple Mac 832 x 624 49.
Touch Screen Driver Installation The PT1545R is available with both RS232 and USB connections. The touch driver is located on the enclosed CD-ROM for these operating systems: Windows® 7, VISTA 64/32 bits, XP, 2000, ME, 98, NT 4.0, CE, XP Embedded, Linux, Apple® Mac OS. Please Note: The PT1545R is Microsoft ® Windows® HID (Human Interface Device) compatible if you use the USB touch screen interface. No additional software driver is required for general operation of the touch screen.
PT1545R Install Instructions: If you are using a PC running Windows® 7, VISTA, XP, 2000, ME, 98, NT4.0, follow the instructions below: 1. Power on the PC. 2. Be sure the USB or the RS-232 Serial cable is connected from the PC to the LCD display. 3. Open the CD-ROM. 4. Follow the step-by-step instructions as shown on the pop-up windows. If you are using a PC running Windows® XP Embedded, follow the instructions below: Express: 1. Power on the computer. 2.
If you are using a PC running Windows® CE, follow the instructions below: 1. Power on the computer. 2. Make sure that the RS232 or USB cable is connected to the computer. 3. Using Platform Builder, build an image file by following the step-by-step instructions found in the zipped file on the CD-ROM. If you are using a PC running Linux or Apple® Mac OS, follow the instructions below: 1. Power on the computer. 2. Make sure that the RS232 or USB cable is connected to the computer. 3.
Product Registration and Technical Support Register Your Planar Products Today Thank you for choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www.planar.com/support/product_registration.html.
Planar Systems, Inc. Customer Service 24x7 Online Technical Support: http://www.planar.com/support 1195 NW Compton Drive Beaverton, OR 97006-1992 Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States. Hours: 24 hours a day, 7 days a week © 2010 Planar Systems, Inc. 5/10 Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice.
