Contents Preface .........................................................................................2 Installation....................................................................................4 Unpacking............................................................................................................................................................................... 4 Adjust height and angle of Tilt stand..................................................................................
Preface This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright. All rights are reserved.
Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean the LCD Monitor screen: -- Power off the LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag. -- Gently clean the screen with dampened rag. 2. Do not place the LCD Monitor near a window. Exposing the monitor to rain water, moisture or sunlight can severely damage it. 3. Do not apply pressure to the LCD screen.
Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot.
Adjust height and angle of Tilt stand 40o The monitor screen may be raised or lowered and tilted (-5 to 40 degree). To raise or lower the monitor screen, place hands on each side of the monitor screen and lift or lower to the desired height as shown in the right figure. 5o 170o 170o Figure 1-1 CAUTION: * When lowering the monitor screen avoid catching your hand and fingers between the monitor screen and the tilt stand base.
Connecting the AC Power 1. Connect the power cord to the LCD Monitor.(See Fig. 1-4) 2. Connect the power cord to an AC power source. 3. Turn the AC power switch to On. AC Power switch AC Power Jack Power Cord Figure 1-4 Connecting the USB Hub 1. Connect the “A“ end of the USB cable to your computer. 2. Connect the “B “end of the USB cable to the USB hub on the monitor. 3. Connect USB compliant products directly to the USB hub on the monitor. ( See Fig 1-5) Figure 1-5 Setting Up the LCD Monitor 1.
Display Controls User Controls A brief description and the location of all LCD Monitor functions controls and indicators Figure 2-1 1 Push to turn ON or turn Off. MENU 2 Activates OSD main menu. EXIT 3 Exit OSD display / DV mode hot key. SOURCE 4 Select DVI or D-SUB signal source. (Toggle Switch) AUTO 5 Hot key for manually auto adjusting the display. LED 6 Green when the monitor is on, Amber when in power saving mode, and Dark when off.
Adjusting the Monitor's Display The monitor has four function control buttons to select among functions shown on OSD menu, designed for easy user-viewing environments. OSD Function Menu To activate the OSD Main menu, simply press ”Menu” button , the menu diagram will pop up on the screen as shown on Fig. 2-2 Use the 4D+1 key to navigate through the function you want to adjust. Push the 4D+1 key to enter a sub-menu and adjust the value. Push the 4D+1 key again to exit the sub-menu.
Function Description Figure Function Function Description The following DV mode display setting can be selected by OSD (STANDARD/TEXT/sRGB/MOVIE/GAMING/PHOTO) Default setting: TEXT DV MODE Adjust the brightness. Factory setting: 100.0% Adjust the image contrast. Factory setting:50.0% Adjust the sharpness. Factory setting: 50% BRIGHTNESS CONTRAST SHARPNESS AUTO CONTRAST Adjust the CONTRAST to the optimal value for the (D-SUB or DVI-I video-input level automatically.
Choose different color temperature (9300K, 7500K, sRGB, USER). Color Temperature Default is USER. USER mode adjustable. Adjust the contrast and brightness of each color of the white balance. RED GREEN BLUE GAIN Allows you to adjust the Red/Green/Blue color gain. RED GREEN BLUE OFFSET Allows you to adjust the Red/Green/Blue color offset. Adjust color depth, increasing this value makes pictures more colorful, decreasing makes pictures less colorful. SATURATION Adjustable value from -100 to 100.
Information Input Select Provide information about resolution, H/V frequencies, and polarity of the input signal. This OSD informs the user the current signal that is displayed. This OSD will automatically turn off after 2 seconds or by pressing the “Exit” key. This OSD gives a warning when the selected input signal is not active. After power on or when the input signal become inactive, this warning appears. OSD Warnings No signal OSD shall be shown after around 0.5sec from video mode detection.
This function gives warning about input resolution or OSD Warnings refresh rate that the monitor cannot display. If video signal is not at the proper timing when the OUT OF RANGE monitor powers on or input signal is changed, this message opens and it disappears after 45 seconds, or by "EXIT" key. When the monitor is displayed for the first time and the Auto Adjust resolution is 800x600 and above, the monitor will auto (Analog Input adjust itself.
OSD Lock Out Function OSD Lock Function allows you to lock out the OSD menu and the button keys. To activates the OSD lock function, the monitor must be in a normal display mode and the information menu as shown in fig-2-4 must be activated. Then follow the instructions below. Figure 2-4 Option 1: OSD lock – all buttons be locked except the “POWER” button.
Technical Information Specifications LCD Panel Size Display Type Resolution Display Dot Display Area (mm) Display Color 26" Active matrix color TFT LCD 1920 x 1200 1920 x (RGB) x 1200 550.08 x 343.8 (H x V) 16.7M (RGB 8 bit) Video Input Signal Input Impedance Polarity Amplitude Multi-mode Supported Analogue RGB ; Digital TMDS 75 Ohm ± 2% (VGA) Positive, Negative (VGA) 0 - 0.7 ± 0.05 Vp (VGA) Horizontal Frequency: 31 ~ 93.
Power Management Mode Power Consumption* AC Input LED Color DPM ON 135W maximum 240 VAC Green DPM OFF 2W maximum 240 VAC Amber DC switch off 1W maximum 240 VAC Disconnected 2W maximum 240 VAC Meeting VESA DPM requirements measured from AC Input end of AC power cord.
Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing.
(75Hz) 1280x720 (60Hz) 1280x960 (60Hz) 1280x960 (70Hz) 1280x960 (75Hz) 1280x1024 VESA-1024-60Hz 1280x1024 VESA-1024-75Hz 1360x768 60Hz 1440x900 Red. BLKing 60Hz 1440x900 60Hz 1440x900 75Hz 1680x1050 Red. BLKing 60Hz 1680x1050 60Hz 1680x1050 75Hz 1600x1200 VESA-1200-60Hz 1600x1200 VESA-1200-70Hz 1600x1200 VESA-1200-75Hz 1920x1200 Red. BLKing 60Hz 1920x1200 60Hz 75.06 44.772 59.855 60 60 70 70 75 75 64 60 80 75 75 75 55.469 59.901 55.935 59.887 70.635 74.984 64.674 59.883 65.29 59.954 82.306 74.892 75 60 87.
Troubleshooting This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected. Attention This LCD Monitor Supports Multiple VGA Modes. Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor.
Product Registration and Technical Support Register Your Planar Products Today Thank you choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www.planar.com/support/product_registration.
