LA1910R and LA1910RTC Operations Manual www.planar.
Table of Contents Usage Notice Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Introduction About the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Installation Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 User Controls Front Panel Controls . . . . . . . . . . . . . .
Usage Notice WARNING – To prevent the risk of fire or shock hazards, do not ! expose this product to rain or moisture. WARNING – Please do not open or disassemble the product as this ! may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: Turn off the product before cleaning. Use only a dry soft cloth or clean room wiper when cleaning the LCD panel surface.
Introduction About Planar’s LA1910R / LA1910RTC The LA19 is a 19” flat panel screen with an active matrix, thin-film transistor (TFT), liquid crystal display (LCD). Features include: Dual signal input: Analog VGA and Digital DVI-D Active matrix TFT LCD technology 1280 x 1024 SXGA resolution 19” viewable display area 31.5 ~ 80 kHz horizontal scan 56 ~ 75 Hz refresh rate 0.294mm x 0.294mm pixel pitch 250 cd/m2(typ.) brightness 500:1(typ.
Touch Screen (for LA1910RTC) Capacitive for finger interface Optical Clarity: Up to 88% light transmission Touch Contact Requirement: 3 ms for finger input Surface Scratch Hardness: Cannot be scratched using any stylus with Mohs' rating of less than 6.5.
Package Overview LCD Display Power Adapter Power Cord VGA Signal Cable Quick Start Guide Touch Screen Driver Installation CD-ROM (for LA1910RTC) LCD Display
Installation Product Overview • Front View LCD Display • Rear View Connector Ports “A&B”
• Connector Ports “A” • Connector Ports “B” USB (For LA1910RTC)
Connecting the display (Figure 1.1) To configure this monitor, please refer to the following figure and procedures. 1. Be sure all equipment is off. 2. Connect the DC power cord to the power connector. Plug one end of the AC power cord into the power adapter, and the other end into an electrical outlet(1). 3. For the PC with Analog output: connect the VGA signal cable from display VGA input connector to the 15-pin connector of your host computer and tighten the screws(2). 4.
Figure 1.
User Controls Front Panel Controls Menu button Displays the OSD menus Select / Auto Select- To select the adjustment items from OSD menus. Auto- To activate the “Auto Adjustment” function to obtain an optimum image Brightness Minus / Minus To adjust brightness press the “-” button first 1. Decreases the brightness of the display image 2. Decreases value of the adjustment items. Brightness Plus / Plus To adjust brightness press the “-” button first 1.
How to Use the OSD Menus 1. Press the “Menu” button to pop up the on-screen menu and to select between the four main menus. 2. Choose the adjustment items by pressing the “Select/Auto” button. 3. Adjust the value of the adjustment items by pressing the “ ” button.
On-Screen Display Menus First OSD Menu: Auto-Adjustment Choose this function to obtain an optimum image. Contrast This function allows the user to adjust the image crispness. Contrast adjusts the difference between white and black shades. Horizontal Position Changes the horizontal position of the image. Vertical Position Changes the vertical position of the image. Frequency Changes the display data frequency to match the frequency of the graphic card.
On-Screen Display Menus Second OSD Menu: Display Mode Selects this function to view the display resolution, vertical refresh, and horizontal scan of the current mode. OSD Off-Time Adjusts the time it takes for the OSD menu to disappear. Language Chooses the language you need. Text-Graphic Toggles between VGA text mode (mode M03H) and graphic mode (mode M13H). Sharpness Adjust the sharpness of the image.
On-Screen Display Menus Third OSD Menu: Volume Controls the sound volume. Mute Disables the sound immediately. Video Source Changes the video mode between multiple connections.
On-Screen Display Menus Fourth OSD Menu: Color Adjusts the color temperature. Color Adjustment-Red Adjusts the red color of the display. Color Adjustment-Green Adjusts the green color of the display. Color Adjustment-Blue Adjusts the blue color of the display.
Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or visit Planar Support at www.planar.com/support. See support contact information on rear cover. Problem: No image appears on screen. Check that all the I/O and power connectors are installed correctly and well connected as described in the “Installation” section. Make sure the pins of the connectors are not crooked or broken.
Warning Signal There are instances when you will see warning messages from the LCD screen. This occurs when the LCD is unable to receive the exact signal from the computer graphic card. There are three instances when this may happen. Please check the cable connections or contact your local dealer or Planar Support for more information. No Signal The LCD has been powered on but it isn’t receiving a signal from the computer graphic card. Check all the power switches, power cables, and VGA signal cable.
Product Dimensions
Compatibility Modes Resolution V.Frequency (Hz) H.Frequency (kHz) IBM VGA 640 x 350 70 31.5 IBM VGA 640 x 400 70 31.5 IBM VGA 640 x 480 60 31.5 IBM VGA 720 x 400 70 31.5 VESA VGA 640 x 480 72 37.9 VESA VGA 640 x 480 75 37.5 VESA SVGA 800 x 600 56 35.2 VESA SVGA 800 x 600 60 37.9 VESA SVGA 800 x 600 72 48.1 VESA SVGA 800 x 600 75 46.9 VESA XGA 1024 x 768 60 48.4 VESA XGA 1024 x 768 70 56.5 VESA XGA 1024 x 768 75 60.0 VESA SXGA 1280 X 1024 60 64.
Touch Screen Driver Installation Touch driver information is located on the enclosed CD-ROM for the following operating systems: Windows Me/2000/98/XP series. Driver Installation Process: 1. Before installing the touch driver be sure that the USB cable is disconnected from the LCD. Please read "Readme.txt" before you start the installation Please note: Once the CD-Rom is loaded into the PC, it should automatically load the installation software. If not, follow steps 2-5 below. 2. Open the CD-Rom 3.
Planar Systems, Inc. Customer Service 24x7 Online Technical Support: http://www.planar.com/support Americas Support Tel: 1-866-4PLANAR (866-475-2627) Hours: M-F, 7:30am - 5pm Pacific Time Europe and Asia-Pacific Support Tel: +358-9-420-01 Hours: M-F, 7:00am - 4pm CET © 2004 Planar Systems, Inc. 02/04 Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice.
