LA2250RTPW Open Frame Touch Screen Monitor USER’S GUIDE www.planar.
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced,translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows is a registered trademark of Microsoft, Inc.
Table of Contents Usage Notice Precautions............................................................................................................................. 1 Introduction About LA2250RTPW ............................................................................................................. 2 Touch Screen for LA2250RTPW ........................................................................................... 2 Package Overview ............................................................
Usage Notice ! ! Warning - To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. Warning - Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: • Turn off the product before cleaning.
Introduction About LA2250RTPW The LA2250RTPW is a 21.5" flat panel screen with an active matrix, thin-film transistor (TFT) edge-lit LED liquid crystal display (LCD). This unit is to be used as commercial and light industrial equipment only. Features include: • Direct Analog signal input • Direct Digital signal input • Edge-lit LED LCD • 1920 x 1080 resolution • 21.5" viewable display area - 16:9 aspect ratio • 31.47 ~ 82.3 KHz horizontal scan • 56 ~ 75 Hz high refresh rate • 0.24825mm x 0.
Package Overview LCD Display Power Cord VGA Signal Cable DC Power Supply DVI-D Cable USB Cable ( A to B ) Side Brackets Landing Strip Bracket Screws (Quantity 4) 3
Installation Product Overview • Front View • Bottom View VGA DVI RJ Type 4 DC IN USB
Attaching the L-Brackets Depending on your mounting scheme, you may use the L-brackets to mount your displays onto your wall or device. Find a suitable location for attaching L-brackets. A. The left and right sides B. The top and bottom Bracket Bracket OR Bracket Bracket Note: You will need a screwdriver to attach the L-brackets. Your kiosk touch monitor includes two L-brackets and four screws (M4x8).
Side Mount For Your Monitor This monitor can be mounted to a wooden or concrete wall with 4 screws and a pair brackets on the opposite sides (see page 5) OR 33.0 mm 230.0 mm 6 1.
Customer -Supplied Panel Material Recommendations 1. Wooden wall: Ø4.5mm thru holes for M4 screws w/nuts, or no thru holes, screws for wood 4mm. 2. Sheet metal: concealed head threaded studs M4 w/nuts. RECOMMENDED CUSTOMER PANEL CUT-OUT 531.4 mm 518.4 mm 214.0 mm 314.3 mm 327.3 mm 180.0 mm 7 214.0 mm .9 R5 4- 180.
VESA Mount for Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monitors, and corresponding with the standards of flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor. To mount the monitor on a UL certified swing arm or other mounting fixture, follow the instructions included with the mounting fixture to be used.
Connecting the Display (Figure 10.1) To setup this display, please refer to the following figure and procedures. 1. 2. 3. 4. 5. 6. ! Be sure all equipment is turned off. Connect the DC plug to the power connector on the monitor and the other end into an electrical outlet (10.1). Connect the D-SUB or DVI cable from the display’s D-SUB or DVI input connector to the D-SUB or DVI connector of your host computer and tighten the screws (10.1).
(Figure 10.
User Controls Back Panel Controls Icon Key Name Menu Up Down Select Power OSD Key Menu off status Menu on status Menu appear Menu disappear/return to main item Brightness Main item select up/Adjust up Contrast Main item select down/Adjust down Enter/Select sub-item function Power On/Off 11
How to Use the OSD Menus Icon Key Name Menu Up Down Select Power 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the five functions in the main menu. 2. Choose the adjustment items by pressing the “Select” button. 3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button. 4. With the OSD menu on screen, press “ Menu” button to return main menu or exit OSD. 5.
On-Screen Display Menus Main OSD Menu: ITEM CONTENT Contrast The monitor luminance level control. Brightness The monitor backlight level control. Auto Adjust Fine-tune the image to full screen automatically. Left/Right Moving screen image horizontal position to left or right. Up/Down Moving screen image vertical position to up or down. Horizontal size The screen image horizontal dot clock adjustment. Fine The screen image pixel phase adjustment.
Appendix Troubleshooting IIf you are experiencing trouble with the display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. ► Check that all the I/O and power connectors are correctly and well connected as described in the “Installation” section. ► Make sure the pins of the connectors are not crooked or broken. Problem: Partial Image or incorrectly displayed image.
Warning Signal If you see warning messages on your screen, this means that the display cannot receive a clean signal from the computer graphics card. Below are the three kinds of warning signals you may receive. Please check the cable connections or contact your sales representative or our service center for more information. No Signal This message means that the display has been powered on but it cannot receive any signal from the computer graphics card.
Product Dimensions 517.4 mm 313.3 mm 46.0 mm Front View Side View 100.0 mm 106.7 mm 100.0 mm 100.
Compatibility Modes Mode Resolution H-Frequency(khz) V-Frequency(hz) IBM VGA 720X400 31.47 70 IBM VGA 640X480 31.47 60 Apple MacII 640X480 35.00 66 VESA VGA 640X480 37.86 72 VESA VGA 640X480 37.50 75 VESA VGA 800X600 35.16 56 VESA VGA 800X600 37.88 60 VESA VGA 800X600 48.08 72 VESA VGA 800X600 46.88 75 Apple Mac 832X624 49.72 75 VESA XGA 1024X768 48.36 60 VESA XGA 1024X768 56.48 70 VESA XGA 1024X768 60.02 75 VESA SXGA 1280X1024 64.
Touch Screen Driver Installation The LA2250RTPW is available with USB connection. The touch driver is available at www. planar.com/support for these operating systems: Windows® 7/8, VISTA, XP, 2000, CE, XP Embedded, Linux kernel 2.6.x (32 bit & 64 bit), Apple® Mac OS. (Windows 7/8 Multi touch without driver) Please Note: 1. The LA2250RTPW is Microsoft® Windows® HID (Human Interface Device) compatible if you use the USB touch screen interface.
LA2250RTPW Calibration Instruction: Calibrating the touch screen in Windows 7/8: 1. Tap the Start button, Control Panel and then Hardware and Sound. 2. Under Tablet PC Settings, tap Calibrate the screen for pen or touch input. 3. On the Display tab, under Display options, tap Calibrate and then Yes to allow the program to make changes. 4. Follow the on-screen instructions to calibrate the touch screen.
20
LA2250RTPW Install Instruction: If you are using a PC running, Windows® 7/8, VISTA, XP, 2000, follow the instructions below: 1. 2. 3. 4. Power on the PC. Make sure that the USB cable is connected to the computer. Visit www.planar.com/support. Follow the step-by-step instructions as shown on the pop-up windows. If you are using a PC running driver Linux kernel 2.6.x (32 bit & 64 bit), follow the instructions below: 1. 2. 3. 4. Power on the PC. Make sure that the USB cable is connected to the computer.
Technical Support Cables and Accessories To find cables and accessories for your Planar monitor, touch screen or other Planar products visit our online store at www.PlanarOnline.com. Technical Support Visit Planar at http://www.planar.com/support for operations manuals, touchscreen drivers, warranty information and access to Planar’s Technical Library for online trouble shooting.
Planar Systems, Inc. Customer Service 24x7 Online Technical Support: http://www.planar.com/support 1195 NW Compton Drive Beaverton, OR 97006-1992 Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States. Hours: 24 hours a day, 7 days a week © 2013 Planar Systems, Inc. 11/13 Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. Technical information in this document is subject to change without notice.
